Full-body interface pressure testing as a method for performance evaluation of clinical support surfaces

A method for evaluating the performance of clinical support surfaces is required by designers in their efforts to produce better clinical support surfaces that will reduce the incidence of pressure ulcers. In this study, a Pressure Index (P_index) is defined which is derived from an analytical equation used to evaluate the average interface pressure, the peak pressure, the magnitude of the peak pressure, and the number of peak pressures on the entire body. The type of subjects needed to represent a population of users as well as the head of bed elevations necessary to simulate clinical applications were integrated with the P_index to create a single-value mean pressure index which can be used to evaluate any type of surface. To determine the accuracy and repeatability of the mean pressure index, three surfaces (a standard hospital innerspring, a replacement foam mattress, and a low-airloss surface) were tested and evaluated using this method. The low airloss performed the best and the standard innerspring clearly performed the worst (p < 0.0001). The method appeared to accurately and reproducibly predict the relative performance of the three surfaces in reducing pressure.     

Stable inversion and parameter variations

As part of the process of automatically guiding an aircraft, we have been successful in using stable inversion to compute a desired bounded state trajectory and corresponding bounded control. In addition to this feedforward control, we must also construct a regulator to address modeling errors and disturbances. With respect to modeling errors we find that the stable inversion procedures used are so accurate that the regulator can assume a simple form, say a linear regulator about the desired trajectory. We show that under the appropriate assumptions, the bounded state trajectory and bounded control computed through stable inversion depend continuously on the parameters of the system. This is a consequence of a mathematical result that we prove about the continuous dependence of the “particular solution” of a time varying nonlinear system driven by a bounded input. This is distinct from the usual continuous dependence of the initial value problem for systems.     

Mechanisms of Hf dopant incorporation during the early stage of chemical vapor deposition aluminide coating growth under continuous doping conditions

A laboratory-scale chemical vapor deposition (CVD) reactor was used to perform “continuous” Hf doping experiments while the surface of a single-crystal Ni alloy was being aluminized to form an aluminide (β-NiAl) coating matrix for 45 minutes at 1150 °C. The continuous doping procedure, in which HfCl₄ and AlCl₃ were simultaneously introduced with H₂, required a high HfCl₄/AlCl₃ ratio (>∼0.6) to cause the precipitation of Hf-rich particles (∼0.1 μm) at grain boundaries of the coating layer, with the overall Hf concentration of ∼0.05 to 0.25 wt pct measured in the coating layer by glow-discharge mass spectroscopy (GDMS). Below this ratio, Hf did not incorporate as a dopant into the growing coating layer from the gas phase, as the coating matrix appeared to be “saturated” with other refractory elements partitioned from the alloy substrate. In comparison, the Hf concentration in the aluminide coating layer formed on pure Ni was in the range of ∼0.1 wt pct, which was close to the solubility of Hf estimated for bulk NiAl. Interestingly, the segregation of Hf and the formation of a thin γ′-Ni₃Al layer (∼0.5 μm) at the coating surface were consistently observed for both the alloy and pure-Ni substrates. The formation of the thin γ′-Ni₃Al layer was attributed to an increase in the elastic strain of the β-NiAl phase, associated with the segregation of Hf as well as other refractory alloying elements at the coating surface. This phenomenon also implied that the coating layer was actually growing at the interface between the γ′-Ni₃Al layer and the β-NiAl coating matrix, not at the gas/coating interface, during the early stage of the coating growth.     

A novel processor architecture with exact tag-free pointers

Along with the success of Java, garbage collection advances to embedded and real-time systems. In this paper a novel RISC processor architecture that lays the foundation for efficient real-time garbage collection in hardware and guarantees pointer integrity at the machine-code level is proposed. This article summarizes the most commonly used garbage collection methods and points out problems of contemporary software-based solutions to motivate architectural support for garbage collection.     

Correlation of damage, dry band arcing energy, and temperature in inclined plane testing of silicone rubber for outdoor insulation

Silicone rubber samples, filled with 30% alumina trihydrate, subjected to the ASTM inclined plane test, show good correlation between the measured harmonic power components of dry band arcing and the surface temperature recorded with a thermovision camera. The simultaneous study of the low frequency fast Fourier transform and variations in temperature shows that when the temperature rises above 100/spl deg/C there is a well defined increase in the low frequency harmonic components of the measured power; however, this trend is not verified by the fundamental component. The eroded mass of the samples is measured independently by a laser approach and a model to rank the tested samples using the inclined plane test is developed. The model is validated by applying it to both the recorded harmonic power components and temperature, resulting in the correct ranking of damage on the samples tested in the inclined plane test.     

Preparation and characterisation of titanium dioxide films for catalytic applications generated by anodic spark deposition

The advanced plasma electrochemical process of anodic spark deposition (ASD) was used to generate photoactive titanium dioxide films on titanium metal substrates. A shift to easier-to-machine substrates was demonstrated by the deposition of a titanium film with physical vapour deposition onto different materials such as glass, silicon, and stainless steel prior to ASD. Obtained films were characterised by scanning electron microscopy, surface area measurement (Brunnauer-Emmett-Teller method, BET), X-ray diffraction, electron-probe microanalysis, and glow discharge spectroscopy. Additionally, film thickness was determined by eddy current measurements. Standard ASD conditions were defined as 180 V applied voltage over a 180 s hold time, a voltage ramp of 20 V/s, a duty cycle of 0.5 and a frequency of 1500 Hz. Most prominent characteristics of the titanium films produced under these standard conditions are a film thickness of ≤80 μm, a surface area of approximately 51 m²/g (BET) and an anatase content of approximately 30% and rutile content of approximately 70%. Furthermore, the film formation process is elucidated and the dependence of film thickness on deposition time and the dependence of the anatase and rutile content on the deposited mass are shown for varying ASD conditions.     

Development of open-cathode polymer electrolyte fuel cells using printed circuit board flow-field plates: Flow geometry characterisation

Open-cathode air-breathing fuel cells have the advantage of reduced system complexity and simplified operation, as oxygen is taken directly from ambient air without the need for blowers/compressors. In this study, printed circuit boards (PCBs) are used as flow-field plates. The use of PCBs offers the potential for significant cost reduction due to their well-established manufacturing processing and low materials cost. This study investigates the effect of varying the cathode geometry (parallel and circular) and opening ratios (43%, 53% and 63%) on fuel cell performance using polarisation curves, electrochemical impedance spectroscopy (EIS) and thermal imaging. The results obtained indicate that circular openings afford lower Ohmic resistance than parallel flow-field designs, which helps improve contact between the gas diffusion layer and flow-field plate. However, flow-field plates with circular openings suffer from greater mass transport limitation effects. Likewise, greater opening ratios offer better mass transport but increased Ohmic resistance as a result of the reduced area of lands/ribs. The thermal imaging results reveal lower temperature in the middle of the fuel cell due to “bowing” of the printed circuit board flow field plates which reduces the local current density. A trade-off between these factors results in a design with a maximum area specific power density of 250 mW cm⁻².