Embedded is the new paradigm(s)

Embedded computing moved beyond toasters quite some time ago, but there are still misconceptions about what embedded computers do. Some of those misconceptions come from an old-fashioned view of what a computer is.     

Influence of ion bombardment on the properties and microstructure of unbalanced magnetron deposited niobium coatings

The effect of the ion bombardment to unbalanced magnetron deposited, approximately 1.5 and 4.5 μm thick, Nb coatings have been investigated as the bias voltage was varied from U_B=−75 to −150 V. Increasing bias voltage increased the hardness of the coating from 4.5 to 8.0 GPa. This was associated with residual stress and Ar incorporation into the Nb lattice. Strong {110} texture developed in the samples deposited at low bias voltages, while beyond U_B=−100 V a {111} texture became dominant. However, strong {111} texture was observed only with the thicker 3Nb coatings. Secondary electron microscopy investigation of the coating topography showed fewer defects in the thicker coatings. All coatings exhibited good corrosion resistance, with the thicker coatings clearly outperforming the thinner ones. Excessive bias voltages (U_B=−150 V) was found to lead to poor adhesion and loss of corrosion resistance.     

Accuracy Investigations of Boundary Element Methods for the Solution of Laplace Equations

Boundary element methods (BEMs) are approved methods for an efficient numerical solution of problems, which are based on a Laplace equation. Here, the solution of electrostatic field problems, steady current flow field problems, and magnetostatic field problems is considered. Focus of this paper is on investigations of accuracy of direct formulations, which are based on Green's theorem. Different types of coupling of computational domains are examined with respect to accuracy and convergence behavior of iterative solvers of the linear system of equations. Furthermore, the influence of singular and nearly singular integrals and the influence of matrix compression techniques to the accuracy of the solution are observed     

Analytical pyrolysis as a tool for the study of plastic coals

The technique of analytical pyrolysis has been used to characterize 40 similar mid-rank western Kentucky coals of widely differing ASTM Gieseler plasticity. Certain pyrolysis/g.c. variables were shown to correlate well with both ASTM Gieseler and isothermal plasticity. Highly plastic coals were shown to exhibit certain characteristic peaks in the 450 °C pyrogram which were absent in the pyrogram of the non-plastic coals. Two coals, representing the two extremes in plasticity, were selected for further study. After extraction with solvents such as DMF the characteristic peaks were absent in the 450 °C pyrogram of the extraction residue of the highly plastic coal. These peaks were also shown to decrease with increasing severity of air oxidation of the plastic coal. This technique appears to be a useful tool for the analysis of mid-rank plastic coals and supports the view that the substances contained in the bitumen fraction of these coals are involved in the development of the plastic state.     

Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.