给水管网计算中的数据转换方法

在给水管网计算中,通过建立环-管段矩阵、环-节点矩阵以及输入节点流量、节点坐标等少量数据,通过计算和数据转换,便可求得经济管径、管段设计流量、节点水压值、水厂供水量、管网造价、年费用折算值等。采用该方法进行管网计算,可以减少40%～70%的计算时间。     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

新型低压抽屉式开关柜在冶金系统的应用

介绍新型低压抽屉式开关柜的结构性能和特点，并与早期低压柜作了比较。阐述了新型低压抽屉式开关柜在冶金系统应用中的几点改进情况。     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

一种多晶硅高温压力传感器

制作压力传感器时，在二氧化硅层上淀积多晶硅膜，既可利用优良的机械特性，又可保证压敏电阻与衬底间具有良好的绝缘性，由此可大大提高器件的温度特性。介绍了一种多晶硅压力传感器的原理和设计。实验结果表明，这类传感器具有灵敏度好，精度高等特点，电路工作范围为０－２５０℃，且具有良好的温度稳定性。     

参数化图形库技术

本文论述了参数化图形库的实现原理，建立了以尺寸叠加算法为基础的参数化图形库开发工具，利用这种开发工具建立的图形数据可以由数据库管理，方便有效。     

Grain Boundary Sliding in Fatigue of Pure Aluminum

The distributions of plastic strain near grain boundaries induced by fatigue loading were investigatedby the fiducial grid method in pure aluminum specimens, and the resulted grain boundary sliding(GBS) was systematically analysed. The results show that the strain field near a grain boundary isnonuniform. GBS is restricted by the junction of grain boundaries and causes discontinuities of bothdisplacement and strain. A peak value of shear strain was created in short-range area across the grainboundary. GBS plays an important role in cyclic softening and secondary hardening. The control fac-tor of GBS is the relative orientation between two grains and the macro orientation of the grainboundary rather than the ∑ value of the boundary.     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process