PVC防水卷材的配方研究

研究了利用废旧软聚氯乙烯回收料(旧料)生产PVC塑料防水卷材的配方及其对卷材拉伸性能的影响。结果表明,PVC塑料卷材的拉伸强度和断裂伸长率随PVC树脂添加比例增加而提高,而相同添加量的SG-3型PVC树脂比SG-5型PVC树脂的拉伸性能高；在试验范围内,增塑剂用量增加,卷材的拉伸强度降低,伸长率先升后降；添加CPE能提高PVC卷材伸长率,但拉伸强度有所下降。当CaCO_3用量低于20份时,卷材的拉伸强度和伸长率随CaCO_3添加量增加而提高。PVC防水卷材的优选配方(质量份)：旧料85份,PVC树脂(SG-3型)15份,DOP 5份,CPE 3份,稳定剂(TLS)0．6份,其它助剂适量。     

甲烷浓度对金刚石薄膜(100)织构生长的影响

以H2和CH4的混合气体为气源,用微波等离子体辅助化学气相沉积法(MPECVD)在1 cm×1 cm S i(100)基体上沉积了金刚石薄膜。研究了不同的甲烷浓度对金刚石薄膜(100)织构生长趋势的影响。分别采用扫描电子显微镜(SEM),Ram an光谱对金刚石膜的表面形貌、质量进行了分析。结果表明,当基体温度为750℃,气压为4.8×103Pa,甲烷浓度为1.4%时,薄膜表面为(100)织构。     

废聚酯饮料瓶裂解制备聚酯清漆

叙述了以废聚酯饮料瓶为原料,经过醇解、酯化以及缩聚等工艺过程,制成透明聚酯清漆。该法为废饮料瓶回收利用开辟了可行之路,也为聚酯清漆找到了廉价的原材料。     

适用于摩托车零件的多层镍电镀工艺

概括目前我国摩托车零件电镀所用镀层组合，对照有关金属覆盖层的国家标准，认为摩托车零件应用多层镍组合，并提供了工艺配方。     

充油S-SBR加工行为的研究

在中试装置上合成相对分子质量分布较宽的充油S-SBR，考察不同环烷油和芳烃油填充量的充油S-SBR的流变性能和混炼行为。结果表明，增大油的填充量能提高充油S-SBR的流动性能，充芳烃油S-SBR相对于充环烷油的S-SBR对温度更敏感，宽相对分子质量分布的充环烷油S-SBR的混炼性能优于S-SBR1204及E-SBRl778，竟相对分子质量分布的充芳烃油S-SBR的混炼性能优于S-SBR1204，Solprene380和E-SBR1712。     

SIMULATION OF THERMALLY-COUPLED DISTILLATION PROCESSES WITH TWO LIQUID PHASES

This paper modifies a mathematical model for distillation with two liquid phases so as to suit for thermally coupleddistillation with two liquid phases and advances an algorithm based upon the modified Naphtali-Sandholm method.Thestructures of Jacobi matrix and its submatrices of all types are given.The multiple phase flash method combined with acomparison of free energies for determination of the liquid phase split in stage is used.Seperation of butanol-water-propanol ternary system is employed to justify the method mentioned above.Satisfactory results are obtained.     

离子膜使用过程中起泡的原因及危害

分析并列举了离子交换膜在使用过程中鼓泡的原因，阳极液质量浓度；pH值；阴极液质量浓度；电流密度；开停车及盐水质量等因素都可以造成膜鼓泡，形成针孔。提出了相应的预防措施。     

江苏省耐盐生物质能源植物选育和生物柴油制备研究

江苏省有近67万公顷沿海盐土滩涂资源,发展适应这些土地资源的油料植物对促进江苏省生物质能的产业化具有极大的促进作用.本研究针对江苏省土地资源的特点,自2001年,从江苏盐城种植了近10年的美国耐盐油料植物海滨锦葵6万株自然群体中筛选了40个优良单株,并进行了子代测定.目前已经初步选育出了海滨锦葵优良无性系,含油量从原群体平均的18 %提高到23 %.2005年首次从耐盐油料植物海滨锦葵中成功获得生物柴油实验室样品,并已经得到中石化权威机构检测数据.     

Influence of Hydrostatic Pressure and Humidity on Superplastic Ductility of Two β-Spodumene Glass-Ceramics

The extent of superplastic deformation in two lithium aluminosilicate glass-ceramics was found to be limited either by intergranular cavitation or by the initiation and growth of surface cracks. Tensile tests were performed under a superimposed hydrostatic pressure to distinguish between the two failure mechanisms. Two materials, one with a high flow stress and the other with a low flow stress, were studied. Cavitation was substantially suppressed by hydrostatic pressure in both materials. The strain-to-fracture, however, was enhanced only in the material with the lower flow stress. (In at least one instance the tensile ductility became almost infinite.) In the material with the higher flow stress, failure was caused by the initiation and propagation of cracks from the surface. The crack-propagation mode of failure was found to be sensitive to humidity, raising the possibility of stress-corrosion cracking at high temperatures in glass-ceramic materials.     

脉冲式气流干燥器的模拟与结构优化

针对脉冲式气流干燥器,在以能耗最低为主目标函数的操作优化数学模型的基础上,加入了加速段高度、减速段高度及管径比等参数,建立了结构优化数学模型,以干燥每千克水为主目标函数编制了模型寻优程序,计算得出了物料终湿含量要求范围内的最佳结构参数.