An adaptive genetic algorithm for the time dependent inventory routing problem

In this paper we propose an adaptive genetic algorithm that produces good quality solutions to the time dependent inventory routing problem (TDIRP) in which inventory control and time dependent vehicle routing decisions for a set of retailers are made simultaneously over a specific planning horizon. This work is motivated by the effect of dynamic traffic conditions in an urban context and the resulting inventory and transportation costs. We provide a mixed integer programming formulation for TDIRP. Since finding the optimal solutions for TDIRP is a NP-hard problem, an adaptive genetic algorithm is applied. We develop new genetic representation and design suitable crossover and mutation operators for the improvement phase. We use adaptive genetic operator proposed by Yun and Gen (Fuzzy Optim Decis Mak 2(2):161–175, 2003) for the automatic setting of the genetic parameter values. The comparison of results shows the significance of the designed AGA and demonstrates the capability of reaching solutions within 0.5 % of the optimum on sets of test problems.     

Dynamics of the wet-end section in paper mills

A model representing the wet-end section of a paper mill has been developed to characterize its dynamic behavior during the grade change. The model is based on the mass balance relationships written for the simplified wetend white water network. From the linearization of the dynamic model, higher-order Laplace transfer functions were obtained followed by the reduction procedure to give simple lower-order models in the form of 1^st-order or 2^nd-order plus dead times. The dynamic response of the wet-end is influenced both by the white water volume and by the level of wire retention. Effects of key manipulated variables such as the thick stock flow rate, the ash flow rate and the retention aid flow rate on the major controlled variables were analyzed by numerical simulations. The simple dynamic model developed in the present study can be effectively used in the operation and control. This paper is dedicated to Professor Se Ki Moon on the occasion of his retirement from Hanyang University.     

Mechanical properties and morphology of polymer blends of poly(ethylene terephthalate) and semiflexible thermotropic liquid crystalline polyesters

Two thermotropic liquid crystalline polyesters (TLCPs) with long flexible spacer groups in the main chain were prepared by melt polymerization: one was a homopolymer with only decane groups (LCPHO) and the other was a copolymer with hexane or decane groups (LCPCO) between mesogen units. These polyesters were blended with a matrix polymer of poly(ethylene terephthalate) (PET). Scanning electron microscopy (SEM) revealed the excellent interfacial adhesion between polyester and PET, and the large aspect ratio of polyester microfibrils in the blend fiber made by extruding and drawing the blend through a die. The aspect ratio was estimated by using the modified Halpin-Tsai equation. The fiber with LCPHO showed more extensive fibril formation than that with LCPCO.     

Manufacturing and foaming of high melt viscosity of polypropylene by using electron beam radiation technology

The high melt viscosity of polypropylene was studied by grafting bifunctional monomers, 1,6‐hexanediol diacrylate (HDDA) and tripropylene glycol diacrylate (TPGDA), onto homopolypropylene (HPP) and random ter‐polypropylene (RTPP) under electron‐beam irradiation. Creation of the high‐melt‐viscosity polypropylene was possible at low radiation dosage and low monomer content, under a prohibition of both radiation degradation and homopolymerization. TPGDA monomer was more effective in increasing the melt viscosity of HPP compared with RTPP, whereas HDDA monomer was more effective for enhancing the melt viscosity of RTPP. Such different effects of monomers on melt viscosity may arise from different monomer structures, namely, TPGDA has additional three methyl groups, but HDDA has no methyl groups. Electron‐beam radiation technology, on an increase of the melt viscosity, was much more effective in HPP than RTPP, when compared with virgin polymers. Modified RTPP and HPP with high melt viscosity were capable of foaming with numerous fine cells, of which the modified HPP with 1.5 mmol TPGDA and 0.5 kGy could create more spherical foam cells and its bending strength was 1.5 times more than that of the foamed RTPP. POLYM. ENG. SCI., 46:431–437, 2006. © 2006 Society of Plastics Engineers.     

Creep and drying shrinkage of calcium silicate pastes IV. Effects of accelerated curing

The dependent deformations and evidence of structural changes were measured on pastes of C₃S containing CaCl₂, and on pastes of C₃S or a C₃S/C₂S blend cured at 65°C. It was concluded that the addition of CaCl₂ enhances the role of the “pore component” in controlling irreversible strains even when well-hydrated pastes are dried. The formation of ore stable CSH at 65°C can explain the reduction in time-dependent deformations observed for these pastes. Even though a change in pore size distribution occurs at 65°C, it is not considered to affect irreversible strains in well-hydrated pastes.     

The effct of asymmetries of die exit geometry on extrudate swell and melt fracture

Experimental investigations were performed to see how the die exit geometry and the extrusion velocity influence on extrudate swell and melt fracture for several polymer melts [low-density polyethylene, styrene-butadiene rubber (SBR) and SBR/HAF (carbon black) compound]. Four different types of die exit geometry were considered; 0° (symmetric. usual capillary die), and 30°, 45° and 60° (asymmetric dies) were chosen for the die exit angle. Extrudate diameters were measured without draw-down under isothermal condition. Polymer melts were extruded into an oil that has the same density and temperature as those of the extrudate. Extrudate swells from dies with different diameters were correlated with volumetric flow rates. It was observed that the extrudate swell increases with increasing volumetric flow rate and exhibits through a minimum value at about 45° die exit angle. As to the fracture phenomena, it was observed that the critical shear for the onset of melt fracture increases with the increasing die exit angle up to 45°. However, for 60° die exit angle, the onset of melt fracture is again similar to that of 0° exit angle.     

Synergic influence of a surfactant and ultrasonication on the preparation of soluble,conducting polydiphenylamine/silica‐nanoparticle composites

Conducting polydiphenylamine was used to encapsulate silica nanoparticles through the oxidative polymerization of diphenylamine in the presence of ultrasonic irradiation. The polymerization was performed in the presence of sodium lauryl sulfate as a surfactant. Experiments performed in the absence of ultrasound clearly demonstrated that the application of ultrasonication played multiple roles in the preparation of a composite of polydiphenylamine with silica nanoparticles. Ultrasonication dispersed the silica nanoparticles, converted sodium lauryl sulfate to lauryl alcohol, and augmented the dispersion of the silica‐nanoparticle/polydiphenylamine composite in an organic medium. Silica‐nanoparticle/polydiphenylamine composites were also prepared in the absence of ultrasound and/or sodium lauryl sulfate. The silica‐nanoparticle/polydiphenylamine composites were characterized with Fourier trans form infrared spectroscopy, ultraviolet–visible/near‐infrared spectroscopy, and thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3912–3918, 2006     

Preparation of Monodisperse ZrO2 by the Microwave Heating of Zirconyl Chloride Solutions

Based on the principle that the solubility of a salt decreases as the dielectric constant of the solvent decreases, zirconia powders were prepared by heating a zirconyl chloride solution with a 2-PrOH-water mixture as the solvent. The morphology, size, and size distribution of the resulting particles were highly sensitive to the heating method used on the starting solution. Particles formed under conventional heating methods were polydisperse, agglomerated spherical, or irregularly shaped because of inhomogeneous precipitation through the temperature gradient, the shear force induced by stirring, compositional nonuniformity, and the low heating rate. The present study demonstrated that microwaves provide an excellent means of heating uniformly and rapidly without stirring. The particles resulting from microwave treatment were monodisperse and spherical, with a mean diameter of 0.28 μm.     

Numerical study of coal particle cluster combustion under quiescent conditions

Behavior of ignition and combustion of coal particle cluster under a quiescent condition was numerically simulated by solving balance equations of mass and enthalpy with combustion kinetic models of volatiles and char. Two-flame structure, one flame penetrating into the cluster and the other moving out of the cluster, was predicted during the combustion of coal particle cluster. Effects of radiative heat transfer, group number, ambient temperature, coal particle size, and oxygen concentration on ignition and combustion of coal particle clusters were also analyzed. Simulations indicated that the gas volume fraction of coal particle cluster increases with time after devolatilization. Gas velocity passing through the cluster surface varied significantly at volatile liberation. The ignition time delay was reduced with the increase of ambient temperature. The cluster devolatilization rate and char burning rate increased while the ignition time delay decreased with the increase of ambient oxygen concentration.     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.