Photo‐reduction and adsorption in aqueous Cr(VI) solution by titanium dioxide,carbon nanotubes and their composite

BACKGROUND: This study compared the removal of aqueous Cr(VI) by multi‐walled carbon nanotubes (CNTs) modified by sulfuric acid, titanium dioxide (TiO₂) and composite of CNTs and TiO₂. RESULTS: More than 360 h contact time was needed to completely adsorb 3 mg L^?1 of Cr(VI) by CNTs, indicating that the rate of adsorption by CNTs alone was slow. The reaction time approaching equilibrium depended on the Cr(VI) concentration. XPS analysis of CNTs after adsorbing Cr(VI) showed that the Cr(VI) on the surface of CNTs was partially reduced to Cr(III). A 3 mg L^?1 solution of Cr(VI) was fully photocatalyzed by commercial TiO₂ (Degussa P25) in less than 0.5 h under UV irradiation. Unlike P25, reduction by another commercial TiO₂ (Hombikat UV100) took 4 h and more than 2 h were necessary for reduction by the composite. Thus the efficiency of Cr(VI) photo‐reduction by the composite was lower than by TiO₂, but higher than that by CNTs. XPS analysis of TiO₂ and composite showed the existence of both Cr(VI) and Cr(III) on their surfaces. CONCLUSION: In contrast to TiO₂, the reduction rate of aqueous Cr(VI) using CNTs as adsorbent was slow. P25 had a markedly higher photocatalytic efficiency than the composite or UV100 alone. Using P25 to reduce aqueous Cr(VI) has a higher potential for practical application. The diameters of TiO₂ and CNTs and the ratio of TiO₂/CNTs are key problems in the preparation of TiO₂/CNTs composite. Copyright © 2011 Society of Chemical Industry     

A continuous ultrasound‐assisted packed‐bed bioreactor for the lipase‐catalyzed synthesis of caffeic acid phenethyl ester

BACKGROUND: The focus of this paper is the ultrasound‐assisted synthesis of caffeic acid phenethyl ester (CAPE) from caffeic acid and phenyl ethanol in a continuous packed‐bed bioreactor. Immobilized Novozym^® 435 (from Candida antarctica) is used as the catalyst. A three‐level–three‐factor Box–Behnken design and a response surface methodology (RSM) are employed to evaluate the effects of temperature, flow rate, and ultrasonic power on the percentage molar conversion of CAPE. RESULTS: Based on ridge max analysis, it is concluded that the optimum condition for synthesis is reaction temperature 72.66 °C, flow rate 0.046 mL min^?1, and ultrasonic power 1.64 W cm^?2. The expected molar conversion value is 97.84%. An experiment performed under these optimal conditions resulted in a molar conversion of 92.11 ± 0.75%. The enzyme in the bioreactor was found to be stable for at least 6 days. CONCLUSIONS: The lipase‐catalyzed synthesis of CAPE by an ultrasound‐assisted packed‐bed bioreactor uses mild reaction conditions. Enzymatic synthesis of CAPE is suitable for use in the nutraceutical and food production industries. Copyright © 2011 Society of Chemical Industry     

A novel and rapid fabrication for microlens arrays using microinjection molding

This work reports a novel and effective procedure for manufacturing the mold insert of microlens arrays. First, the microlens arrays master is formed using room‐temperature imprint lithography and photoresist reflow process. Next, electroforming is carried out to fabriccate the metal mold insert from the master. Finally, microinjection molding is used to replicate the molded microlens arrays. The 200 × 200 arrays of molded microlens, with a diameter of 150 μm, a pitch of 200 μm, and a sag height of 11.29 μm for polycarbonate (PC) material and 11.24 μm for polymethylmethacrylate (PMMA) material have been successfully fabricated. The moldability for PMMA material is better than PC material on molded microlens arrays. The average surface roughness of the molded microlens arrays is 4.53 nm for PMMA material and 4.81 nm for PC material. The mold temperature is the most important processing factor for the focal length and sag height of molded microlens arrays. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers.     

Cleaning organized single-walled carbon nanotube interconnect structures for reduced interfacial contact resistance

A method is presented for significantly reducing the interfacial contact resistance of single-walled carbon nanotube (SWCNT) interconnects test-structures. Conventional lithographic cleaning steps are insufficient for complete removal of lithographic residues in SWCNT networks, leading to large interfacial contact resistance. Using improved purification procedures and controlled developing time, the interfacial contact resistance between SWCNTs and contact electrodes of Ti/Au were found to reach values below 2% of the overall resistance in two-probe test-structures of SWCNTs, demonstrating the importance of cleaning lithographic residues from the surface of SWCNTs before the fabrication of metal electrodes. These low-resistance contacts are quite stable over a large temperature range, and represent a step towards the implementation of SWCNTs as future interconnects.     

Synthesis and characterization of novel copolymers with the trimethylsilyl group for deep‐UV photoresists

N‐(4‐Acetoxyphenyl) maleimide (APMI) and three kinds of comonomers bearing a trimethylsilyl group were copolymerized at 60°C in the presence of azobisisobutyronitrile (AIBN) as an initiator in 1,4‐dioxane to obtain the three IP, IIP, and IIIP copolymers. These copolymers were removed from the acetoxy group in a transesterification process into new IVP, VP, and VIP copolymers with a pendant hydroxyl group. Two modified processes were adopted to prepare photoresists using these copolymers. The first process involved mixing the dissolution inhibitor, o‐nitrobenzyl cholate, with the new copolymers. Second, o‐nitrobenzyl cholate was introduced into the copolymers using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) in dimethylformamide (DMF). The cyclic maleimide structure is responsible for the high thermal stability of these copolymers. After irradiation using deep–UV light and development with aqueous Na₂CO₃ (0.01 wt %), the developed patterns showed positive images and exhibited good adhesion to the silicon wafer without using any adhesion promoter. The resolution of these resists was at least 0.8 μm and an oxygen‐plasma etching rate was 1/5.3 to that of hard‐baked HPR‐204. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2791–2798, 2002; DOI 10.1002/app.10255     

Varying the wetting properties of polycarbonate substrate by varying the nanomolding temperature

Polycarbonate (PC) nanofibers were produced using anodized aluminum oxide (AAO) template assisted nanomolding. The effects of temperature on the nanoflow were investigated. It was found that higher temperature apparently enhanced the polycarbonate nanoflow and resulted in longer nanofibers in the same duration. The surface wettabilities of the polycarbonate nanofiber coated substrates showed apparent dependency on the morphology of the surface. It was found that larger honeycomb patterns would result in higher hydrophobicity than smaller honeycomb patterns. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Dynamic Stabilization of DNA Assembly by Using Pyrrole-Imidazole Polyamide

We used N-methylpyrrole (Py)-N-methylimidazole-(Im) polyamide as an exogenous agent to modulate the formation of DNA assemblies at specific double-stranded sequences. The concept was demonstrated on the hybridization chain reaction that forms linear DNA. Through a series of melting curve analyses, we demonstrated that the binding of Py−Im polyamide positively influenced both the HCR initiation and elongation steps. In particular, Py−Im polyamide was found to drastically stabilize the DNA duplex such that its thermal stability approached that of an equivalent hairpin structure. Also, the polyamide served as an anchor between hairpin pairs in the HCR assembly, thus improving the originally weak interstrand stability. We hope that these proof-of-concept results can inspire future use of Py−Im polyamide as a molecular tool to modulate the formation of DNA assemblies.     

White-light fluorescent nanoparticles from self-assembly of rhodamine B-anchored amphiphilic poly(poly(ethylene glycol)methacrylate)-b-poly(glycidyl methacrylate) block copolymer

Rhodamine B (RhB)-anchored amphiphilic poly(poly(ethylene glycol)methacrylate)-b-poly(glycidyl methacrylate) block copolymer (PPEGMA-b-PGMA/RhB) has been prepared by a sequential atom transfer radical polymerization and post-functionalization of RhB. The chemical structure of PPEGMA-b-PGMA/RhB is characterized with gel-permeation chromatography, Fourier-transform infrared spectroscopy, and ¹H nuclear magnetic resonance spectroscopy. PPEGMA-b-PGMA/RhB has shown self-assembly behaviors in tetrahydrofuran and aqueous solutions. The RhB aggregation induced with the inter-molecular interaction of RhB results in the various core–shell structures of the assembled nanoparticles. The photoluminescent properties of the PPEGMA-b-PGMA/RhB nanoparticles are structure-dependent and exhibit yellow-light, blue-light, and white-light emissions. The fluorescent organic nanoparticles of PPEGMA-b-PGMA/RhB in aqueous solution show low cytotoxicity and have been used as a bio-dye for cell labelling. Internalization of PPEGMA-b-PGMA/RhB nanoparticles into HELA cells to exhibit fluorescent images has been demonstrated.     

Morin,a Flavonoid from Moraceae,Induces Apoptosis by Induction of BAD Protein in Human Leukemic Cells

Evidence suggests that phytochemicals can safely modulate cancer cell biology and induce apoptosis. Here, we investigated the anti-cancer activity of morin, a flavone originally isolated from members of the Moraceae family in human leukemic cells, focusing on apoptosis. An anti-cancer effect of morin was screened with several human leukemic cell lines. U937 cells were most sensitive to morin, where it induced caspase-dependent apoptosis in a dose-dependent manner. It also induced loss of MMP (ΔΨ_m) along with cytochrome c release, down-regulated Bcl-2 protein, and up-regulated BAX proteins. The apoptotic activity of morin was significantly attenuated by Bcl-2 augmentation. In conclusion, morin induced caspase-dependent apoptosis through an intrinsic pathway by upregulating BAD proteins. In addition, Bcl-2 protein expression is also important in morin-induced apoptosis of U937 cells. This study provides evidence that morin might have anticancer properties in human leukemic cells.     

Effects of oxidation and particle shape on critical volume fractions of silver‐coated copper powders in conductive adhesives for microelectronic applications

The effects of oxidation and particle shape on critical volume fractions of silver‐coated copper powders in conductive adhesives are investigated. Silver‐coated copper powders with spherical and flake‐shaped particles were oxidized at temperatures of 30°C, 175°C and 240°C for two hours and dispersed in an epoxy matrix. As silver‐coated copper powders are oxidized at 30°C and 175°C, the critical volume fractions of the conductive adhesives are slightly affected by oxidation and particle shape at these temperatures. As the oxidation temperature approaches 240°C, the critical volume fractions of the conductive adhesives are strongly affected by oxidation temperature and particle shape, owing to the formation of oxides such as Cu₂O on the surface of silver‐coated copper powder—Cu diffuses from the interior to the surface of silver‐coated copper powder and reacts with the oxygen in the air. Silver‐coated copper powder with flake‐shaped particles shows lower critical volume fractions in conductive adhesives than silver‐coated copper powder with spherically shaped particles. Polym. Eng. Sci. 44:2075–2082, 2004. © 2004 Society of Plastics Engineers.