Vortex Dynamics in Bi2Sr2CaCu2O8 Single Crystal with Low Density Columnar Defects Studied by Magnetic Force Microscope

We have studied vortex dynamics in Bi₂Sr₂CaCu₂O₈ single crystal with low density columnar defects by using a magnetic force microscope. Single crystal Bi₂Sr₂CaCu₂O₈ sample was irradiated by 1.3 GeV uranium ion to form artificial pinning centers along the crystalline c-axis. The irradiation dose corresponded to a matching field of 20 gauss. The radius of an individual vortex is approximately 140 nm, which is close to the penetration depth of this material. Magnetic force microscope (MFM) images show that intrinsic crystalline defects such as stacking fault dislocations are very effective pinning centers for vortices in addition to the pinning centers due to ion bombardment. By counting the number of vortex, we found that the flux trapped at each pinning center is a single flux quantum. At higher magnetic field, the vortex structure showed an Abrikosov lattice disturbed only by immobile vortices located at pinning centers. When increasing or decreasing the external magnetic field, the spatial distribution of vortices showed a Bean model like behavior.     

Defect-free sintering of two material powder injection molded components Part II Model

A defect-free, two-material component can be obtained via co-sintering by suitably altering the powder characteristics or compositions, as demonstrated in Part I. In this paper, a model to ascertain the suitability of material systems to be co-sintered without defects such as delamination or interface pores is presented. The model is based on the management of the stress induced due to the difference in shrinkage and an analysis of the in situ strength of the weaker material during sintering. Tool steel in combination with stainless steel admixed with boron and Fe-2Ni admixed with boron are two systems used to validate the model. The predictions of the model are in good agreement with the observations.     

Statistical analysis of subthreshold leakage current for VLSI circuits

We develop a method to estimate the variation of leakage current due to both intra-die and inter-die gate length process variability. We derive an analytical expression to estimate the probability density function (PDF) of the leakage current for stacked devices found in CMOS gates. These distributions of individual gate leakage currents are then combined to obtain the mean and variance of the leakage current for an entire circuit. We also present an approach to account for both the inter- and intra-die gate length variations to ensure that the circuit leakage PDF correctly models both types of variation. The proposed methods were implemented and tested on a number of benchmark circuits. Comparison to Monte Carlo simulation validates the accuracy of the proposed method and demonstrates the efficiency of the proposed analysis method. Comparison with traditional deterministic leakage current analysis demonstrates the need for statistical methods for leakage current analysis.     

Bioresorbable and bioactive polymer/Bioglass® composites with tailored pore structure for tissue engineering applications

An overview about the development of porous bioresorbable composite materials for applications as scaffolds in tissue engineering is presented. A thermally induced phase separation method was developed to fabricate porous foam-like structures of poly(lactide-co-glycolide) (PLGA) containing bioactive glass particle additions (up to 50 wt.%) and exhibiting well-defined, oriented and interconnected porosity. The in vitro bioactivity and the degradability of the composite foams were investigated in contact with phosphate buffer saline (PBS). Weight loss, water absorption and molecular weight measurements were used to monitor the polymer degradation after incubation periods of up to 7 weeks in PBS. It was found that the presence of bioactive glass retards the polymer degradation rate for the time period investigated. The present results show a way of controlling the in vitro degradation behaviour of PLGA porous composite scaffolds by tailoring the concentration of bioactive glass.     

Electromagnetic coupling effects on the cavity measurement of antenna efficiency

Electromagnetic coupling effects on the antenna in a conducting cavity are studied theoretically and experimentally. It is observed in experiments that at the resonant frequencies of the cavity, the input resistance of the antenna attains values two or three orders of magnitude higher than that at frequencies away from resonance. It is shown via theoretical analysis that the input resistance of the antenna measured at the resonant frequencies of the cavity is not merely the loss resistance desired in computing the antenna efficiency, but is actually the sum of the loss resistance of the antenna and the coupling resistance between the antenna and cavity. This coupling effect is demonstrated quantitatively by numerical computations for dipole and monopole antennas. The computational results for the input resistance are in agreement with the measured data. A method is proposed to avoid the cavity-antenna antiresonance in the measurement.     

A combination of differential equations and convolution in understanding the spread of an epidemic

Nonlinear dynamical method of projecting the transmission of an epidemic is accurate if the input parameters and initial value variables are reliable. Here, such a model is proposed for predicting an epidemic. A method to supplement two variables and two parameters for this proposed model is demonstrated through a robust statistical approach. The method described here worked well in case of three continuous distributions. Model predictions could be lower estimates due to under-reporting of disease cases. Anad hoc procedure with a technical note is provided in the appendix An earlier version of this paper was presented at the annual conference of the Indian Society for Mathematical Modelling & Computer Simulation, Bangalore, November 14–15, 2002     

Optimization of a photopolymerizable holographic recording material based on polyvinylalcohol using angular responses

Acrylamide-based holographic recording materials have significant advantages and the composition of these materials has been optimized in terms of energetic sensitivity and diffraction efficiency. As a result, diffraction gratings with an efficiency of almost 80% for energetic exposures of 35 mJ/cm² and a spatial frequency of 1000 lines/mm in photosensitive films 65 μm thick have been obtained. In this paper we present the effects of intensity, thickness, and variation in the concentration of each component by studying the angular responses of the diffraction gratings recorded in each composition.     

Examining a curvilinear relationship between communication frequency and team performance in cross-functional project teams

The performance of a cross-functional team depends on the skillful and innovative combination of information and expertise from all team members. Communication is the medium through which team members share the information required for successful amalgamation. In this work, we postulate that both high and low levels of team communication can impede team performance, thus leading to a curvilinear relationship between team performance and team communication. To test this hypothesis, the relationships between face-to-face, e-mail, and telephone communication and team performance were examined for 60 cross-functional project teams. E-mail and face-to-face communication were curvilinearly associated with performance, but telephone communication was not. Further analysis of the communication frequency between colocations showed that e-mail is the only medium for which usage increased with distance.     

Efficient design of oversampled NPR GDFT filterbanks

We propose a flexible, efficient design technique for the prototype filter of an oversampled near perfect reconstruction (NPR) generalized discrete Fourier transform (GDFT) filterbank. Such filterbanks have several desirable properties for subband processing systems that are sensitive to aliasing, such as subband adaptive filters. The design criteria for the prototype filter are explicit bounds (derived herein) on the aliased components in the subbands and the output, the distortion induced by the filterbank, and the imaged subband errors in the output. It is shown that the design of an optimal prototype filter can be transformed into a convex optimization problem, which can be efficiently solved. The proposed design technique provides an efficient and effective tool for exploring many of the inherent tradeoffs in the design of the prototype filter, including the tradeoff between aliasing in the subbands and the distortion induced by the filterbank. We calculate several examples of these tradeoffs and demonstrate that the proposed method can generate filters with significantly better performance than filters obtained using current design methods.