Enhanced electron emission from phosphorus-doped diamond-cladsilicon field emitter arrays

Undoped and phosphorus (P)-doped diamond-clad Si field emitter arrays have been successfully fabricated using microwave plasma chemical vapor deposition (MPCVD) technology. The electron emission from the blunt diamond-clad microtips are much higher than those for the pure Si tips with sharp curvature due to a lower work function. Furthermore, the characteristics of emission current against applied voltage for the P-doped diamond-clad tips show superior emission at lower field to the undoped ones. After the examination of Auger electron spectroscopy (AES) and electrical characteristics of as-grown diamond, such a significant enhancement of the electron emission from the P-doped diamond-clad tips is attributed to a higher electron conductivity and defect densities     

Exact evaluation of laser linewidth requirements for optical PSKhomodyne communication systems with balanced PLL receivers

The power penalty induced by imperfect phase recovery in PSK homodyne communication systems with balanced phase-locked loop receivers are exactly evaluated. Optimum phase deviations between the mark-state and the space-state bits are used in this study. This study for the first time shows the imperfect-phase-recovery-induced power penalty as a function of laser linewidth with optimum phase deviations considered. It can be estimated from the theoretical result that an optimal balanced PLL receiver requires the laser linewidth as Δν⩽1.15×10^-6× (bit rate) in contrast to the previous reported one Δν⩽5.88×10^-6× (bit rate). We also point out here that the previously reported laser linewidth requirement was wrongly estimated     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Guest Editors' Introduction: Attacking Functional Verification through Hybrid Techniques

Hybrid techniques are effective for exploring interesting corner cases, coverage holes, invariant variations, and so forth, in the general area of directed functional validation. However, despite the emergence of several effective hybrid validation techniques, several questions still remain. The five articles in this special issue help explain some of the different facets of this area.     

High-temperature sensible-heat storage options

Alkali-metal carbonate salts meet the requirements for high-temperature solar central receiver systems, but because of their corrosiveness they present special problems in the design of storage tanks. In order to reduce corrosion and temperature sufficiently to retain strength in the storage containing wall, internal and thermal insulation is required. We present design options and operation criteria for sensible-heat, molten-salt storage with internal insulation.