基于CAN总线的汽车测试解决方案

更高功能的汽车设计带动更复杂的汽车电子测试技术的发展。中国的汽车测试界尤其面对着设备的短缺、技术的匮乏等诸多困难。本文针对中国的汽车电子测试业。介绍了一种集成的软硬件同步平台。它基于CAN总线领域中的PXI总线。及国际广泛应用的测试管理TestStand软件。构建成高集成度、可靠性、升级维护方便、开放彻底的测试系统。     

Modular and rapid testing of SOCs with unwrapped logic blocks

Extensive research has been carried out for test planning of core-based system-on-a-chip devices. Most of the prior work assumes that all of the embedded cores are wrapped for test purpose. However, some designs may contain user-defined logic or cores that cannot be wrapped due to area constraints or timing violations. This paper discusses how these unwrapped logic blocks can be tested rapidly by adapting the TestRail architecture, which uses only the test control mechanism and the test instructions available through the IEEE 1500 standard for embedded core test. A new test scheduling algorithm, which facilitates a concurrent test of both unwrapped logic blocks and IEEE 1500-wrapped cores, is proposed, and experiments show that it outperforms a previous approach when the available number of tester channels and/or the number of unwrapped logic blocks are small.     

Displacement Discontinuity Method for Fracture Mechanics Analysis of Reissner Plates: Static and Dynamic

This paper is concerned with the displacement discontinuity method applied to the shear deformable plates (Reissner’s and Mindlin’s theories) with cracks subjected to static and dynamic loads. Fundamental solutions of dislocation are derived using the Fourier transform method and the Laplace transformation technique. Boundary integral equations are presented in terms of rotations/displacement on the crack surfaces. The Chebyshev polynomials of the second kind are used to evaluate the integral equations with hypersingular kernels on the crack boundaries and determine the stress intensity factors at the crack tips. Comparisons are made with other numerical solutions to demonstrate the proposed method is accurate both for static and dynamic problems.     

中频反应溅射SiO2膜与直流溅射ITO膜的在线联镀

多数ITO透明导电玻璃生产线在实现SiO2膜与ITO膜在线联镀时，应用SiO2靶射频溅射沉积SiO2膜工艺和ITO靶直流溅射沉积ITO膜工艺，如果SiO2膜应用硅靶反应磁控溅射工艺，存在这种工艺是否可以与ITO靶直流溅射沉积ITO膜工艺在线联用以及如何实现联用的问题。作者对现有的生产线进行了改造设计、加工，做了大量实验、质谱分析和多项测试研究，成功地实现反应溅射SiO2膜与ITO膜在线联镀，做到SiO2镀膜室的工作状态的变化基本上不影响ITO镀膜室的工艺条件。     

关于最远点判定及直径的唯一性

给出了点到有界集最远点的一些必要或充分条件，然后对直径的唯一性也给出了一些判定条件。     

纳米超晶格热电材料的研究进展

随着热电材料制备技术和性能研究的发展，纳米超晶格热电薄膜已受到人们的关注，简要介绍了有关纳米超晶格热电材料的结构、热电机理及制作技术，并指出了存在的问题和可能的发展方向。     

Wideband miniature G-shaped antenna for dual-band WLAN applications

A wideband miniature G-shaped coplanar waveguide fed dual-band antenna for a wireless local area network (WLAN) is proposed. The proposed antenna has good radiation pattern and can provide two separate measured impedance bandwidths of 0.55 GHz (about 22.9% centred at 2.42 GHz) and 2.85 GHz (about 50.9% centred at 5.60 GHz), so that it easily covers the required bandwidths for WLAN operation. This design results in a small antenna size of 22 times 18.5 mm with the ground plane regarded as part of the antenna structure.     

电源对介质阻挡放电(DBD)激发准分子(XeCl*)辐射的影响

本文对电源参数如电压幅值、频率及正负电压对介质阻挡放电激发准分子XeCl 紫外 (30 8nm)辐射的影响进行了实验研究。结果表明 ,UV辐射随电压幅度的增加而增强 ,但效率下降 ;提高频率 ,增加了放电次数 ,导致UV辐射的增强 ;此外 ,在较高的频率下 ,电压上升沿变陡 ,使得电子获得的能量主要用于原子的激发和电离。正、负电压放电的不对称源于电极结构的不对称而引起的放电过程的差异 ,负电压内电极可向放电管中馈入更多的能量 ;比较发光光谱可判断生成准分子的等离子体化学过程没有明显的差别     

省煤器管开裂原因分析

对省煤器开裂管进行了化学成分及宏、微观分析。分析结果表明，在高温高压条件下，在其焊缝溶合区出现粗大的魏氏组织，管材中的珠光体组织产生了不同程度的球化，而母材组织又存在严重的带状组织。在过热条件下熔合区极易出现裂纹，并由此快速扩展，造成省煤器管开裂。     

纳米NiO粉体的制备及其表征

采用溶胶转化－凝胶法制备了纳米级NiO粉体。Ni(OH)2粉体的TG－DSC分析表明：在升温速率为10℃/min的条件下，粉体在489K时开始显著分解，626K时分解完毕。X－射线衍射分析表明：分解产物为纯净的NiO2。NiO粉体的化学成分分析表明：其纯度高于国家标准。TEM电镜分析表明：NiO粉体呈单分散的球形或棒状颗粒。对NiO粉体的热敏性能有待进一步研究。