Phase inversion and its effect on the properties of polyester polyurethane cationomers

Polyester polyurethane cationomers are prepared using polyester polyol of molecular weight 2000 as soft segments, N-methyl diethanolamine as chain extender, glycolic acid as quaternization agent, methyl ethyl ketone as solvent, and 4,4'-diphenylenemethylene diisocyanate (MDI) as diisocyanate. Properties of the films cast from solutions and emulsions are studied by infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, and tensile-elongation testing. Ionization can cause phase separation and produces increased cohesion in the hard domains. The dispersion process can be divided into three stages involving a separation of hard segment aggregates due to adsorption of water on their surface, water entering into hard segment microionic lattics, and finally a rearrangement of agglomerates to form microspheres. The dispersion can disrupt the order in the hard domains and an increased phase separation.     

高分子助剂处理造纸污水的应用研究

采用动态滤水仪模拟造纸湿部滤水成型过程，对高分子助剂在木浆纸污水处理过程中的影响进行了初步的探讨。结果表明，对于木浆造纸污水，两性淀粉、阳离子聚丙烯酰胺、高分子助留剂SG01均能显著降低污水中的总固形物含量，污水的CODCr值也有一定程度的降低，添加1％的两性淀粉、150～200g／t的阳离子聚丙烯酰胺或0．9％的高分子助留剂SG01时，可使污水中的总固形物含量降低40％～55％；而CODCr的去除率则在40％～58％左右。     

ABS树脂生产现状及发展趋势

本文概述了ＡＢＳ树脂国内外生产现状，技术动向及需求预测，对我国ＡＢＳ树脂的发展提出了建议。     

利用震动磨超细粉碎天然羟基磷灰石

本文利用震动磨对羟基磷灰石进行超细粉碎,优选出震动磨超细粉碎的最佳工艺条件。利用震动磨研磨可以得到粒度分布单一的粉体样品,D50为2.001μm。     

Nonisothermal crystallization kinetics of poly(butylene terephthalate)/montmorillonite nanocomposites

The melt intercalation method was employed to prepare poly(butylene terephthalate) (PBT)/montmorillonite (MMT) nanocomposites, and the microstructures were characterized with X‐ray diffraction and transmission electron microscopy. Then, the nonisothermal crystallization behavior of the nanocomposites was studied with differential scanning calorimetry (DSC). The DSC results showed that the exothermic peaks for the nanocomposites distinctly shifted to lower temperatures at various cooling rates in comparison with that for pure PBT, and with increasing MMT content, the peak crystallization temperature of the PBT/MMT hybrids declined gradually. The nonisothermal crystallization kinetics were analyzed by the Avrami, Jeziorny, Ozawa, and Mo methods on the basis of the DSC data. The results revealed that very small amounts of clay (1 wt %) could accelerate the crystallization process, whereas higher clay loadings reduced the rate of crystallization. In addition, the activation energy for the transport of the macromolecular segments to the growing surface was determined by the Kissinger method. The results clearly indicated that the hybrids with small amounts of clay presented lower activation energy than PBT, whereas those with higher clay loadings showed higher activation energy. The MMT content and the crystallization conditions as well as the nature of the matrix itself affected the crystallization behavior of the hybrids. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3257–3265, 2006     

PVdF-HFP/P123 hybrid with mesopores: a new matrix for high-conducting, low-leakage porous polymer electrolyte

Highly conducting porous polymer electrolytes comprised of poly(vinylidene-fluoride-co-hexafluoropropylene) (PVdF-HFP), polyethylene oxide-co-polypropylene oxide-co-polyethylene oxide (P123), ethylene carbonate (EC), propylene carbonate (PC), and LiClO₄ were fabricated. The PVdF-HFP/P123 hybrid polymer membranes were made with a phase inverse method and the electrolyte solution uptake was carried out in glove box to avoid the moisture contamination. It was found that when a small amount of polymer surfactant (P123) was blended into the PVdF-HFP, mesopores with well-defined sizes were formed. Impedance spectroscopy showed that the room temperature conductivity of (PVdF-HFP)/P123 polymer electrolytes increased as the content of P123 increased up to 4×10⁻³ S/cm. Nitrogen adsorption isotherms, electrolyte solution uptake, porosity measurements, and SEM micrographs showed that the enhanced conductivity was due to increase the pore volume, pore density, and electrolyte uptake. The highest conduction was found when the weight ratio of P123 to PVdF-HFP was 70%, when big channels were formed in the hybrid polymer membrane. Furthermore, blending P123 in PVDF-HFP reduced the pore size of polymer membrane, therefore, the solution leakage was also reduced. These polymer electrolytes were stable up to 4.5 V (vs Li/Li⁺) and the performance of the model lithium ion battery made by sandwiching the polymer electrolyte between a LiCoO₂ anode and a MCMB cathode, showed great promise for the use of these polymer electrolytes in lithium ion batteries.     

Preparation and ionic conductivity of solid polymer electrolyte based on polyacrylonitrile‐polyethylene oxide

The transparent and flexible solid polymer electrolytes (SPEs) were fabricated from polyacrylonitrile‐polyethylene oxide (PAN‐PEO) copolymer which was synthesized by methacrylate‐headed PEO macromonomer and acrylonitrile. The formation of copolymer is confirmed by Fourier‐transform infrared spectroscopy (FTIR) measurements. The ionic conductivity was measured by alternating current (AC) impedance spectroscopy. Ionic conductivity of PAN‐PEO‐LiClO₄ complexes was investigated with various salt concentration, temperatures and molecular weight of PEO (Mn). And the maximum ionic conductivity at room temperature was measured to be 3.54 × 10^?4 S/cm with an [Li⁺]/[EO] mole ratio of about 0.1. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 461–464, 2006     

Synthesis and properties of polystyrene‐b‐poly(ethylene oxide)‐b‐polystyrene triblock copolymers

A series of well‐defined and property‐controlled polystyrene (PS)‐b‐poly(ethylene oxide) (PEO)‐b‐polystyrene (PS) triblock copolymers were synthesized by atom‐transfer radical polymerization, using 2‐bromo‐propionate‐end‐group PEO 2000 as macroinitiatators. The structure of triblock copolymers was confirmed by ¹H‐NMR and GPC. The relationship between some properties and molecular weight of copolymers was studied. It was found that glass‐transition temperature (T_g) of copolymers gradually rose and crystallinity of copolymers regularly dropped when molecular weight of copolymers increased. The copolymers showed to be amphiphilic. Stable emulsions could form in water layer of copolymer–toluene–water system and the emulsifying abilities of copolymers slightly decreased when molecular weight of copolymers increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 727–730, 2006     

Photoinitiated crosslinking of ethylene‐vinyl acetate copolymers and characterization of related properties

Photoinitiated crosslinking of EVA in the presence of benzophenone (BP) as photoinitiator and triallyl isocyanurate (TAIC) as crosslinker and characterization of the related properties have been studied by gel determination, heat extension, DSC, DMTA, TGA, and mechanical measurements. The photoinitiated crosslinking efficiency of the EVA‐BP‐TAIC system and various factors affecting the crosslinking process, such as photoinitiator and crosslinker and their concentrations, irradiation temperature, and irradiation atmosphere were studied in detail and optimized by comparison of gel contents. The results show that the EVA samples with a thickness of 1 mm are readily crosslinked to a gel content of above 80% with 5 s UV‐irradiation under optimum conditions. The data from the heat extension and DSC show that the crosslinking density of photocrosslinked EVA increase and their crystallinities decrease with increasing the UV‐irradiation time. At the same time, photocrosslinking of EVA leads to a lowering of the melt temperature and a decrease of heat of fusion. The DMTA results show that photocrosslinking increases the amorphous phase and storage modulus of the crosslinked EVA, but does not change the glass transition temperature. The data from TGA and mechanical tests give evidence that the thermal stability and mechanical properties of photocrosslinked EVA samples are much better than those of the uncrosslinked EVA. POLYM. ENG. SCI., 47:1761–1767, 2007. © 2007 Society of Plastics Engineers     

Synthesis and thermotropic liquid‐crystalline behavior of novel main‐chain poly(aryl ether ketones)

Novel aromatic poly(ether ketones) containing bulky lateral groups were synthesized via nucleophilic substitution reactions of 4,4′‐biphenol and (4‐chloro‐3‐trifluoromethyl)phenylhydroquinone (CF‐PH) with 1,4‐bis(p‐fluorobenzoyl)benzene. The copolymers were characterized by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and polarized light microscopy observation. Thermotropic liquid‐crystalline behavior was observed in the copolymers containing 40, 50, 60, and 70 mol % CF‐PH. The crystalline–liquid‐crystalline transition [melting temperature (T_m)] and the liquid‐crystalline–isotropic phase transition appeared in the DSC thermograms, whereas the biphenol‐based homopolymer had only a melting transition. The novel poly(aryl ether ketones) had glass‐transition temperatures that ranged from 143 to 151°C and lower T_m's that ranged from 279 to 291°C, due to the copolymerization. The polymers showed high thermal stability, and some exhibited a large range in mesophase stability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1347–1350, 2003