Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Transmission capacity of optical path overhead transfer schemeusing pilot tone for optical path network

Photonic networks based on the optical path concept and wavelength division multiplexing (WDM) technology require unique operation, administration, and maintenance (OAM) functions. In order to realize the required OAM functions, the optical path network must support an effective management information transfer method. The method that superimposes a pilot tone on the optical signal appears very interesting for optical path overhead transfer. The pilot tone transmission capacity is determined by the carrier to noise ratio which depends on the power spectral density of the optical signal. The pilot tone transmission capacity of an optical path network employing WDM technology is elucidated; 4.5 kb/s transmission can be realized when the pilot tone modulation index is set at 3%     

~（131）Ⅰ—MIBG比活度对鼠心肌交感神经囊泡内外摄取的影响

研究了两种比活度的１３１Ⅰ－ＭＩＢＧ在正常及利血平抑制后在鼠体内的分布，结果表明：注射后４ｈ，正常鼠心肌对３．２２ＴＢｑ／ｇ的ＭＩＢＧ摄取为９．０８％ＩＤ／ｇ，明显高于对１８．５ＧＢｑ／ｇ的摄取（４．８７％ＩＤ／ｇ）。计算表明，比活度主要影响了鼠心肌交感神经囊泡内摄取，而与囊泡外摄取无关．当ＭＩＢＧ用于心肌显像时，高比活度的ＭＩＢＧ有利于诊断。     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

An improved Gaussian approximation for probability of bit-erroranalysis of asynchronous bandlimited DS-CDMA systems with BPSK spreading

This paper analyzes probability of bit-error (P_e) performance of asynchronous bandlimited direct-sequence code-division multiple-access systems with binary phase-shift keying spreading. The two present methods of P_e analysis under bandwidth-efficient pulse shaping: the often-cited standard Gaussian approximation and the characteristic function (CF) method suffer from either a low accuracy in regions of low P_e (< 10^-3) or a prohibitively large computational complexity. The paper presents an alternate method of P_e analysis with moderate computational complexity and high accuracy based on a key observation. A sequence of chip decision statistics (whose sum yields a bit statistic) forms a stationary, m-dependent sequence when conditioned on the chip delay and phase offset of each interfering signal. This observation permits the generalization of the improved Gaussian approximation previously derived for the rectangular pulse and the derivation of a numerically efficient approximation based on the CF method. Numerical examples of systems using the square-root raised-cosine and IS-95 pulses illustrate THE P _e performance, user capacity and the accuracy of the proposed method     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

A robust adaptive pole‐placement controller without strictly positive real condition

This paper considers the adaptive pole‐placement control problem for system (1) with unmodelled dynamics η_n dominated by a small constant ε multiplied by a quantity independent of ε but tending to infinity as the past input, output, and noise grow. Using bounded external excitation and randomly varying truncation techniques, we give a design method of adaptive pole‐placement controller. It is shown that the closed‐loop system is globally stable, the estimation error for the parameter contained in the modelled part is of order ε, and the closed‐loop system under the adaptive pole‐placement control law is suboptimal in the sense of $$\mathop{\lim\sup}\limits_{{n\to\infty }}{1\over n}\mathop{\sum}\limits_{i=0}^n{\left({A^{*}(z)y_{n}‐L(z)C(z)w_{n}‐B(z)R(z)y_{n}^{*}}\right)^{2}{\leq}O({\varepsilon}^{2})+\gamma^{2}\mathop{\sum}\limits_{j=1}^q{b_{j}^{2}}}$$\nopagenumbers\end while the SPR condition used usually in other papers is replaced by a stability condition. Copyright © 2001 John Wiley & Sons, Ltd.