PAN/FPU Composite Nanofiber Membrane with Superhydrophobic and Superoleophobic Surface as a Filter Element for High-Efficiency Protective Masks

Recently, because of the outbreak of COVID-19, the demand for various types of filter elements in protective materials has increased globally. Furthermore, new requirements for the filtration performance of PM2.5 liquid (oil) particles have been put forward. In this work, Superhydrophobic and superoleophobic composite nanofibers with excellent filtration capacity for oil and salt particles are developed through the modification of polyacrylonitrile (PAN) by fluoro-polyurethane (FPU) doping. The results show that the PAN/FPU composite nanofibers doped with 9 wt% FPU has a uniform fiber morphology with a diameter of 240 ± 30 nm. Compared to the pure PAN nanofibers, the water-based contact angle of PAN/FPU increases from 90 ± 5° to 151 ± 5°, and the oil-based contact angle increases from 58 ± 2° to 152 ± 3°. Importantly, at a high flow rate of 95 L min⁻¹, the filtration efficiency of the PAN/FPU nanofiber membrane for 0.3 µm oil particles increases from 92 ± 1% to 99.2 ± 0.1%. After cyclic loading, the filtration efficiency of 0.3 µm oil particles remains above 98%. Meanwhile, the filtration efficiency for 0.3 µm salt particles remains at 98.23 ± 0.1%. The PAN/FPU nanofiber membrane developed in this work is effective in applications and has good market prospects as a protective filtration material.     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

基于地质勘查技术的矿山环境地质灾害预防探析

中国矿产资源总量庞大,很多矿产资源开采难度较高,勘查和解决好矿山环境地质灾害,是从业人员面临的难题之一。简述了利用地质勘查技术勘查矿山环境地质灾害的重要性,分析了典型矿山环境地质灾害类型,介绍了先进地质勘查技术,并给出了相关技术支撑下的矿山环境地质灾害预防对策,以提升矿山资源开采安全性。     

近2年我国锆铪及锆化学制品雕生产、贸易及研发概况

介绍了我国近2年来海绵锆、锆铪制品和锆化学品的生产、进出口概况,以及重要研发进展。我国工业级海绵锆产量从2003年的100t增加到2005年的174t,2005年的销售量达到150t;锆粉与锆-铝消气剂等年产量在10t左右;锆材和锆设备年产量在100t以上;锆化学制品品种有10余种,年产量已达到20×104t。锆砂的沸腾氯化工艺、锆铪的MIBK法分离工艺、以电熔ZrO2为原料制取粗ZrCl2工艺和Al-Y复合ZrO2粉的生产工艺等的研发工作,都取得了突破性进展。     

冬季CO2水玻璃砂促硬防蠕变技术

介绍了使用一种专用改性荆加入普通水玻璃中，使CO2水玻璃砂在低温环境下也能速硬，可防止铸型（芯）蠕变的技术。     

用原料添加法提高钼粉粒度的探讨

叙述了在钼粉的工业化生产条件下采用原料添加法来提高最终粉末粒度，改善原料工艺性能的试验。研究表明：在钼酸铵原料中添加一定组份的钥粉，能有效地改善钼酸铵在动态焙解还原时的分散性和流动性，选择不同的添加量和添加粉粒度，可有效地把钼粉的ＦＳＳＳ粒度从２．５μｍ提高到４．２μｍ，从而可根据用粉要求，选择合适的添加工艺，来制取理想的钼粉。     

镁合金与钛合金的瞬间液相扩散焊

为实现镁合金AZ31B与钛合金Ti6A14V的可靠连接，研究了两者以Al为中间层的瞬间液相扩散焊接头的微观结构与连接强度。研究结果表明：当焊接时间为180min时，焊接温度是影响界面反应热力学与动力学的主要参数，其对接头的微观组织、接头界面新生相构成与连接强度有重要影响。保温温度低于450℃时，AZ3IB／AI界面无液相产生，无法实现AZ31B与Ti6A14V的可靠连接；保温温度在450℃～480℃变化时，温度对AZ31B／Al／Ti6A14V界面反应的动力学因素有明显影响，且直接决定了焊后接头新生相的构成与分布。470℃保温180min的接头剪切强度较高（72．4MPa），达到AZ31B母材（86MPa）的84．2％。     

Ti—Al二元合金的成分对组织和力学性能的影响

用金相、扫描电镜和X射线衍射研究了6种不同Al含量Ti-Al二元合金铸态和退火态的组织结构和相组成的特征和变化。从结晶动力学的观点,分析了合金的结晶凝固过程。采用三点弯曲方法研究了合金的抗弯性能同Al含量的关系。结果表明,Al含量为34 wt%,经1100℃/30 h退火的合金抗弯性能最好,Al含量偏离34wt%,都对合金的力学性能不利。     

喷射成形与铸造7A60合金的微观组织对比研究

利用喷射成形技术制备了7A60合金。借助扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD）等手段研究了喷射成形与铸造7A60合金微观组织的特点。结果表明，铸造7A60合金的组织粗大，偏析严重。喷射成形7A60合金主要由细化的等轴晶组成，无明显偏析。与传统铸锭冶金工艺相比，喷射成形工艺大大提高了冷却速率，显著细化了7A60合金的微观组织。     

齿轮精锻的数值模拟与实验研究

本文对空心直齿圆柱齿轮的精锻成形过程进行三维刚塑性有限元模拟和实验研究。通过有限元数值模拟和实验研究 ,得出了直齿圆柱齿轮精锻过程的金属流动规律和变形力学特征 ,揭示了直齿圆柱齿轮精锻过程的变形机理 ,数值模拟结果与实验结果吻合较好