Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Perturbation analysis and control of two-class stochastic fluid models for communication networks

This paper uses stochastic fluid models (SFMs) for the control and optimization (rather than performance analysis) of communication network nodes processing two classes of traffic: one is uncontrolled and the other is subject to threshold-based buffer control. We derive gradient estimators for packet loss and workload related performance metrics with respect to threshold parameters. These estimators are shown to be unbiased and directly observable from a sample path without any knowledge of underlying stochastic characteristics of the traffic processes. This renders them computable in online environments and easily implementable for network management and control. We further demonstrate their use in buffer control problems where our SFM-based estimators are evaluated based on data from an actual system.     

Anaerobic biodecolorization of textile reactive anthraquinone and phthalocyanine dyebaths under hypersaline conditions.

The biological decolorization of two industrial, spent textile reactive dyebaths was investigated using a suspended-growth, halophilic mixed culture fed with glucose. Dyebath I contained mainly Reactive Blue 19 (RB19), an anthraquinone dye, whereas dyebath II contained mainly Reactive Blue 21 (RB21), a phthalocyanine dye. Batch assays under anaerobic conditions with the two neutralized dyebaths resulted in 87 and 37% extent of decolorization for dyebaths I and II, respectively. The rate of glucose utilization and the extent of acetate production were impacted in the presence of each dyebath as compared to the control culture. However, dyebath decolorization occurred despite moderate culture inhibition. Reuse of a biologically renovated RB19-containing dyebath in the dyeing process resulted in reproducible but not identical cotton fabric shades as compared to a standard dyeing (i.e., control) using fresh water. This difference is attributed to a variable degree of RB19 aggregation during the dyeing process and is not related to the efficiency of the biodecolorization process. Further improvement of the redyeing efficiency will lead to the development of an in-plant, closed-loop decolorization system resulting in significant water conservation and minimization of textile pollutants such as salt and dyes.     

Linearity stablized fiber-optic thermometer using pseudo-heterodyne phase detection

A temperature sensor using a fiber-optic Fabry-Perot interferometer is described. A pseudo-heterodyne detection scheme is adopted to read the light phase difference in the Fabry-Perot interference output. A higher harmonic components comparison method is used to stabilize the system and to increase detection linearity. This system realizes not only highly sensitive temperature sensing with good linearity and minimal adjusting error, but also application to the sensing of other physical quantities such as vibrations. Additionally, the signal-to-noise ratio and distortion of the detected signal are investigated as functions of fiber end reflectivity. These results will be useful in designing a high performance fiber-optic Fabry-Perot thermometer.     

Hot-carrier reliability of 20V MOS transistors in 0.13 μm CMOS technology

This paper presents results of reliability investigation of 20 V N-Drift MOS transistor in 0.13 μm CMOS technology. Due to high performances required for CMOS applications, adding high voltage devices becomes a big challenge to guarantee the reliability criteria. In this context, new reliability approaches are needed. Safe Operating Area are defined for switch, V_ds limited and V_gs limited applications in order to improve circuit designs. For V_ds limited applications, deep doping dose effects in drift area are investigated in correlation to lifetime evaluations based on device parameter shifts under hot carrier stressing. To further determine the amount and locations of hot carriers injections, accurate 2D technological and electrical simulations are performed and permit to select the best compromise between performance and reliability for N-Drift MOS transistor.     

Fast numerically stable computation of orthogonal Fourier?Mellin moments

An efficient algorithm for the computation of the orthogonal Fourier-Mellin moments (OFMMs) is presented. The proposed method computes the fractional parts of the orthogonal polynomials, which consist of fractional terms, recursively, by eliminating the number of factorial calculations. The recursive computation of the fractional terms makes the overall computation of the OFMMs a very fast procedure in comparison with the conventional direct method. Actually, the computational complexity of the proposed method is linear O(p) in multiplications, with p being the moment order, while the corresponding complexity of the direct method is O(p²). Moreover, this recursive algorithm has better numerical behaviour, as it arrives at an overflow situation much later than the original one and does not introduce any finite precision errors. These are the two major advantages of the algorithm introduced in the current work, establishing the computation of the OFMMs to a very high order as a quite easy and achievable task. Appropriate simulations on images of different sizes justify the superiority of the proposed algorithm over the conventional algorithm currently used     

Reduction of optical beat interference using gain-saturated RSOA in upstream WDM/SCM optical links

A new scheme for reducing optical beat interference (OBI) noise in optical network units is proposed for subcarrier multiplexing-based access network applications. The optical spectrum of the transmit lasers is broadened by using a radio frequency (RF) clipping tone with a modulation depth greater than one. This reduces the impact of the OBI noise. The distortions caused by an RF clipping tone are also suppressed by introducing a gain-saturated reflective optical amplifier, which shows the characteristics of high-pass filter. The proposed scheme has been verified by measuring the error vector magnitude of 16QAM signal with 20 Mbps. Error-free transmission has been achieved even when the light of OBI-noise-causing lasers is stronger than that of the signal laser by 7 dB     

On Routh-Pade model reduction of interval systems

This paper discusses another generalization of the direct Routh table truncation method for interval systems. It is shown that the existing generalization of the direct Routh table truncation fails to produce a stable system, in contradiction to the equivalent result for fixed-coefficients systems. The present method guarantees a stable reduced order model for interval systems as well.     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.