Effect of misalignment on electrical characteristics of ACF joints for flip chip on flex applications

The effect of misalignment on the electrical properties of anisotropic conductive film (ACF) joints is investigated in this work. It is found that along with the increase of misalignment, the connection resistance of ACF joints increases. When the misalignment in x-direction is less than 5 μm, the increase rate of connection resistance is quite large. Then, along with the severity of misalignment, the increase rate becomes smaller. Finally, when the misalignment is close to 20 μm, the increase rate rises again. The Holm's electric contact theory is used for understanding the connection resistance variation. On the other hand, with the increase of misalignment in x-direction, the insulation resistance between ACF joints decreases. If the misalignment exceeded 10 μm, the decrease is prominent for the Ni particle ACF joints. This phenomenon can be explained by the effect of dielectric damage of the epoxy.Computer programs are also developed to calculate the variation of the probability of open and shorting after misalignment and predicate the maximum misalignment tolerance. The results show that the open and shorting probability increase abruptly after misalignment. On the view of pad parameters, the open probability is mainly related to the pad area, while the pads gap is critical to the shorting probability. Large pads gap (small pad width) can reduce the shorting probability obviously. On the other hand, enlarging the pad area by increasing pad length decreases the open probability significantly. So comparing to square shape pad, rectangle shape pad can reduce the failure probability greatly.     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Minimal transistor-only micropower integrated VHF active filter

A minimal integrated filter containing four MOS transistors as the only circuit elements is presented. Voltage tuning is used to set the cutoff frequency and band-edge peaking. A filter test chip occupies an active area of 0006mm2, has acutoff frequency of 40 MHz and dissipates 580W.     

The effects of FG7142 on two types of forgetting in 18-day-old rats.

The authors studied the role of gamma-aminobutyric acid (GABA) in 2 types of forgetting of fear in the developing rat. One type of forgetting studied was that observed after an intermediate retention interval (the "Kamin effect"); the other type studied was that observed after a longer interval (infantile amnesia). Rats were given pairings of an auditory conditioned stimulus with shock, and learned fear was assessed by freezing. Forgetting at an intermediate retention interval (1 hr) was not alleviated by the GABAA receptor partial inverse agonist FG7142 (0, 1, 5, or 10 mg/kg), whereas forgetting at a longer retention interval (48 hr) was alleviated. These results suggest that in the developing rat, forgetting observed at different retention intervals is mediated by different physiological mechanisms. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

High-resolution electron microscopy of the twinning and intergrowth in Ca4Al6SO16 and Ca3SrAl6SO16

The microstructures of unhydrated calcium aluminosulphate Ca₄Al₆SO₁₆ and Ca₃SrAl₆SO₁₆ have been studied by high-resolution electron microscopy (HREM). The results showed that twinning and twinned slabs could be introduced taking the [1 1 2] direction as the twin axis so that it seems to be coincident with the law of twinning formed in body-centred cubic structures. A previously reported superlattice with a repeat period twice that of the fundamental structure along the 〈1 1 0〉 direction has also been found in both matrix and twin variants. The close intergrowth of Ca₃SrAl₆SO₁₆ and another phase, possibly Sr₃Al₂O₆ existing as an inclusion between these two twin variants, was determined and clearly revealed by electron diffraction and HREM images. The coherent interphase boundaries and orientation relationship between them can also be deduced.     

Novel T-rail electrodes for substrate removed low-voltage high-speed GaAs/AlGaAs electrooptic modulators

A novel traveling-wave electrode utilizing capacitively loaded T-rail elements was developed for low-voltage high-speed substrate-removed GaAs/AlGaAs electrooptic modulators. Electrodes with varying dimensions were fabricated and characterized. Electrode phase velocity, characteristic impedance, loss coefficient, and capacitive loading were extracted from the measured s-parameters up to 40 GHz. Electrode was also simulated using a finite-element solver. The measured and calculated electrode capacitance values were found to be in excellent agreement, showing that the electrode can be precisely designed. Approaches were outlined to provide a group velocity-matched very high-speed modulator electrode suitable for a low drive-voltage substrate-removed GaAs/AlGaAs electro-optic modulator     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.