Design of thermophoretic probe for precise particle sampling

We proposed a design methodology for improved thermophoretic probes that can sample particles with high spatial resolution. A bending vibration analysis for the instantaneous motion of a probe has been done together with direct observation of the probe motion and flow disturbance for systematic study of the effect of different designs on particle sampling. Direct observation of the motion of thermophoretic sampling probes revealed that the probe with a low stiffness would result in inaccurate particle sampling. Based on these, the thermophoretic sampling probe was modified to minimize probe vibration and flow disturbance and this modified design was confirmed to sample particles with higher spatial resolution than the original one by examining transmission electron microscope (TEM) images of particles collected in a flame.     

A positive‐working photosensitive polyimide based on thermal cross‐linking and acidolytic cleavage

A novel positive‐working photosensitive polyimide (PSPI) based on a poly(hydroxyimide) (PHI), a crosslinking agent having vinyl ether groups, and a photoacid generator (PAG) was prepared. The PHI as a base resin of the three‐component PSPI was synthesized from 4,4′‐oxydiphthalic anhydride and 2,2′‐bis(3‐amino‐4‐hydroxyphenyl)hexafluoropropane through ring‐opening polymerization and subsequent thermal cyclization. 2,2′‐bis(4‐(2‐(vinyloxy)ethoxy)phenyl)propane (BPA‐DEVE) was used as a vinylether compound and diphenyliodonium 5‐hydroxynaphthalene‐1‐sulfonate was used as a PAG. The phenolic hydroxyl groups of the PHI and the vinyl ether groups of BPA‐DEVE are thermally crosslinked with acetal structures during prebake step, and the crosslinked PHI becomes completely insoluble in an aqueous basic solution. Upon exposure to UV light (365 nm) and subsequent postexposure bake (PEB), a strong acid generated from the PAG cleaves the crosslinked structures, and the exposed area is effectively solubilized in the alkaline developer. The dissolution behavior of the PSPI containing each 11.5 wt % of BPA‐DEVE and of the PAG was studied after UV exposure (365 nm) and PEB. It was found that the difference in dissolution rates between exposed and unexposed areas was enough to get high resolution. A fine positive pattern with a resolution of 5 μm in a 3.7‐μm‐thick film was obtained from the three‐component PSPI. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

Synthesis and comparative molecular field analysis (CoMFA) of antitumor 3-arylisoquinoline derivatives

In this study a series of 3-arylisoquinoline derivatives were synthesized and cytotoxicity against human melanoma tumor cell evaluated, and a three dimensional quantitative structure-activity relationship was investigated using the comparative molecular field analysis (CoMFA). The results suggested that the electrostatic, steric and hydrophobic factors of 3-arylisoquinolines were strongly correlated with the antitumor activity. Considerable predictive ability (cross-validated r2 as high as 0.721) was obtained through CoMFA.     

Kinetics of volume expansion during infusion of Ringer’s solution based on two volume model

In this work mathematical models were developed to represent the kinetics of volume changes of fluid spaces associated with infusion of Ringer’s solution. During infusion of Ringer’s solution, the human body is assumed to be characterized by the two-fluid space model which has second volume space in addition to the first volume so that fluid exchanges between these two spaces are possible. Various infusion types were tested to accommodate different medical situations. Volunteers were given Ringer’s solution and the changes in blood hemoglobin were detected. From the comparison with experimental data, the two-fluid space model was found to represent adequately the kinetics of human volume expansion during infusion of Ringer’s solution.     

Effect of temperature on polymer migration II: Concentration equation

Polymer migration is a generally well-known phenomenon in a flow field, and it has been verified that the sources of such phenomena are nonhomogeneity of the flow, concentration effects and hydrodynamic interactions between the polymer molecules. In addition, temperature effects were found to be another source of polymer migration. The Langevin equation for a polymer molecule was first derived from single chain dynamics using a kinetic theory for the bead-spring elastic harmonic dumbbell model, as described in part I (reference [1]). In this paper the diffusion equation and concentration profile of the polymer molecules induced by a temperature gradient are obtained from the Fokker-Planck equation. A new differential operator is also introduced to calculate the concentration profile. From the concentration equation obtained in the general flow geometry, we find that in dilute polymer solution there are significant effects on the polymer migration not only due to the nonhomogeneity of the flow field but also due to temperature gradients.     

Analysis of deformation processes in glassy polycarbonate using internal friction measurements during a tensile test

Internal friction has been measured by torsion at 1 Hz during tensile tests performed on glassy polycarbonate at room-temperature. Steady-state flow and transient effects have been studied during continuous tensile tests and strain-rate changes. During steady-state, internal friction and flow-stress vary in a similar way with strain-rate. But during transients, internal friction varies continuously while flow-stress passes through a maximum (or a minimum). These results are interpreted assuming that non-elastic deformation of glassy polymers requires some microscopic discontinuous processes such as motion of defects. Two parameters are considered: the velocity v and the density ρ of mobile defects. Assuming that the former is directly related to the flow stress, it has been shown that internal friction is related to the density of mobile defects ρ. This feature is used to interpret the different stages of a tensile test curve. Activation volumes for both velocity and density of mobile defects are calculated from experimental data.