Selective Oxidation of Methanol to Formaldehyde Using Modified Iron-Molybdate Catalysts

Methanol selective oxidation to formaldehyde over a modified Fe-Mo catalyst with two different stoichiometric (Mo/Fe atomic ratio = 1.5 and 3.0) was studied experimentally in a fixed bed reactor over a wide range of reaction conditions. The physicochemical characterization of the prepared catalysts provides evidence that Fe₂(MoO₄)₃ is in fact the active phase of the catalyst. The experimental results of conversion of methanol and selectivity towards formaldehyde for various residence times were studied. The results showed that as the residence time increases the yield of formaldehyde decreases. Selectivity of formaldehyde decreases with increase in residence time. This result is attributable to subsequent oxidation of formaldehyde to carbon monoxide due to longer residence time.     

Preparation of nanosize Pt clusters using ion exchange of Pt(NH3) 4 2+ inside mesoporous channel of MCM-41

Mesoporous molecular sieve MCM-41 with a Si/Al ratio of 35 was obtained by hydrothermal synthesis using a gel mixture with a molar composition of 6 SiO₂0.1 Al₂O₃1 hexadecyltrimethylammonium chloride 0.25 dodecyltrimethylammonium bromide 0.25 tetrapropylammonium bromide0.15 (NH₄)₂O1.5 Na₂O300 H₂O. The MCM-41 sample was calcined in O₂ flow at 813 K and subsequently ion exchanged with Ca²⁺. A small Pt cluster has been supported on the MCM-41 sample following a procedure using ion exchange of Pt(NH₃) ₄ ²⁺ . The Pt(NH₃) ₄ ²⁺ ion supported on MCM-41 has been activated in O₂ flow at 593 K and subsequently reduced with Fh flow at 573 K, in the same way used for the preparation of a Pt cluster entrapped inside the supercage of zeolite NaY. The resulting Pt cluster supported on the MCM-41 shows hydrogen chemisorption oftotal two H atoms per Pt at 296 K (based on the total amount of Pt) and high catalytic activity for hydrogenolysis of ethane. The chemical shift in¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the Pt cluster is located inside the mesoporous molecular sieve.     

Migration of Intergranular Liquid Films and Formation of Core-Shell Grains in Sintered TiC–Ni Bonded to WC–Ni

When TiC–20 wt% Ni powder mixtures are sintered at 1400°C, relatively large TiC grains possibly containing some Ni form with near-equilibrium shapes. When these specimens are heat-treated again at 1400°C in contact with sintered WC–20 wt% Ni pieces, the liquid films between the TiC grains in the contact region migrate against their increasing curvatures, forming (Ti,W)C solid solution behind them. These migrating liquid films reverse their directions on further heat-treatment. As in other alloys, this liquid film migration must be driven by the coherency strain energy produced by W diffusion at the surface of the dissolving TiC grains. Shells of (Ti,W)C solid solution also form around the cores of TiC grains near the contact region, and this process is probably driven by both coherency strain energy and free energy of mixing. At some contact regions, (Ti,W)C precipitates nucleate and grow, probably driven mainly by the free energy of mixing. In powder mixtures, the formation of core-shell grains is expected to be driven by the coherency strain energy, the free energy of mixing, and the capillary effect.     

Modification of a carbon/carbon composite with a thermosetting resin precursor as a matrix by the addition of carbon black

Carbon/carbon composites were made through the pyrolysis of stabilized PAN felt and phenolic resin with the addition of 5 or 10 wt % carbon black to the matrix and then heat treatment at 600–2500°C. The effects of adding carbon black to the matrix precursor on the physical properties, microstructure, and mechanical properties of the resultant composites were investigated. Adding carbon black not only reduced the weight loss but also limited the shrinkage of the resultant composites. Adding carbon black also accelerated the formation of carbon basal planes in the matrix. At 2500°C, the crystalline stacking height in the composite with 10 wt % added carbon black was 200% greater than that with no additive. The flexural strength of the composite also increased from 15 to 42 MPa (almost 300%). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 333–337, 2006     

Influence of continuous stabilization on the physical properties and microstructure of PAN-based carbon fibers

A continuous stabilization and carbonization process was used to prepare polyacrylonitrile (PAN)-based carbon fibers. The stepwise stabilization of PAN fibers was tried at various temperatures. The effect of stepwise stabilization on the physical properties and microstructure of the final carbon fibers is reported in this article. The fixed temperature in stepwise stabilization is kept below the fusion temperature of PAN precursors to avoid overstabilization of the fibers. The optimum stepwise stabilization process not only increases the amount of ladder polymer in stabilized fiber but also improves the physical and mechanical properties of the resultant carbon fibers. The formation of closed pores from open pores in carbon fiber occurs at 1100°C, but the formation of closed pores occurs at 200°C lower for carbon fiber developed from overstabilized fiber. The effect of continuous stepwise stabilization on the properties of resulting stabilized fibers and the variation in physical properties, element composition, and microstructure of carbon fibers during the carbonization process are also reported in this article.     

Fabrication of SiO2-ZrO2 composite fiber mats via electrospinning

(1 − x)SiO₂-(x)ZrO₂ (x = 0.1, 0.2) composite fiber mats were prepared by electrospinning their sol-gel precursors of zirconium acetate and tetraethyl orthosilicate (TEOS) without using a polymer binder. The electrospun composite fibers were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FT-IR) and mercury porosimetry. The composite fibers having a tetragonal crystalline ZrO₂ were obtained by calcining the electrospun composite fibers at high temperatures. The results show that the structure and crystallization of ZrO₂ in the composite fibers can be controlled by sintering temperature, while the porosity and morphology of the fiber mats did not depend on the sintering temperature.     

Temperature-dependent transparency of poly(HPMA-co-DMA) hydrogels: effect of synthesis parameters

The acrylic comonomers hydroxypropyl methacrylate (HPMA) and N,N-dimethylaminoethyl methacrylate (DMA) have been used in several earlier studies to produce pH-responsive hydrogels. However, these same monomers can also be used to prepare hydrogels that are highly responsive to temperature. One manifestation of this temperature sensitivity is a sharp decrease in hydrogel optical transparency that occurs when the temperature exceeds a critical transition value. For example, a hydrogel that exhibits a swelling transition at the physiological pH value of 7.4 has a transition temperature of about 45 °C when the environmental salt concentration is 0.15 M. The value of the transparency transition temperature is shown to depend on hydrogel synthesis parameters such as comonomer mole ratio, crosslinker mole ratio, and even initiator concentration. By reducing the mole ratio of the crosslinker tetraethylene glycol dimethacrylate (TEGDMA), the transition temperature can be lowered by as much as 15 °C. Environmental salt concentration and solvent polarity are also shown to influence the transition temperature.     

Micro-end-milling of single-crystal silicon

Ductile-regime machining of silicon using micro-end-mill is almost impossible because of the brittle properties of silicon, crystal orientation effects, edge radius of the cutter and the hardness of tool materials. Micro-end-milling can potentially be used to create desired three dimensional (3D) free form surface features using the ductile machining technology for single-crystal silicon. There is still a lack of fundamental understanding of micro-end-milling of single-crystal silicon using diamond-coated tool, specifically basic understanding of material removal mechanism, cutting forces and machined surface integrity in micro-scale machining of silicon. In this paper, further research to understand the chip formation mechanism was conducted. An analysis was performed to discover how the chips are removed during the milling process. Brittle and ductile cutting regimes corresponding to machined surfaces and chips are discussed. Experiments have shown that single-crystal silicon can be ductile machined using micro-end-milling process. Forces generated when micro-end-milling single-crystal silicon are used to determine the performance of the milling process. Experimental results show that the dependence of the cutting force on the uncut chip thickness can be well described by a polynomial function order n. As cutting regime becomes more brittle, the cutting force has more complex function.     

Pseudo-inversion: closure properties and decidability

We consider a pseudo-inversion operation inspired by biological events, such as DNA sequence transformations, where only parts of a string are reversed. We define the pseudo-inversion of a string \(w = uxv\) to be the set of all strings \(v^Rxu^R\), where \(uv \ne \lambda \) and consider the operation from a formal language theoretic viewpoint. We show that regular languages are closed under the pseudo-inversion operation whereas context-free languages are not. Furthermore, we study the iterated pseudo-inversion operation and show that the iterated pseudo-inversion of a context-free language is recognized by a nondeterministic reversal-bounded multicounter machine. Finally, we introduce the notion of pseudo-inversion-freeness and examine closure properties and decidability problems for regular and context-free languages. We demonstrate that pseudo-inversion-freeness is decidable in polynomial time for regular languages and undecidable for context-free languages.     

Usability Principles for Augmented Reality Applications in a Smartphone Environment

Through the rapid spread of smartphones, users have access to many types of applications similar to those on desktop computer systems. Smartphone applications using augmented reality (AR) technology make use of users' location information. As AR applications will require new evaluation methods, improved usability and user convenience should be developed. The purpose of the current study is to develop usability principles for the development and evaluation of smartphone applications using AR technology. We develop usability principles for smartphone AR applications by analyzing existing research about heuristic evaluation methods, design principles for AR systems, guidelines for handheld mobile device interfaces, and usability principles for the tangible user interface. We conducted a heuristic evaluation for three popularly used smartphone AR applications to identify usability problems. We suggested new design guidelines to solve the identified problems. Then, we developed an improved AR application prototype of an Android-based smartphone, which later was conducted a usability testing to validate the effects of usability principles.