Minimum norm mutual coupling compensation with applications in direction of arrival estimation

This paper introduces a new mutual coupling compensation method based on the minimum norm solution to an underdetermined system of equations. The crucial advantage over previous techniques is that the formulation is valid independent of the type of antenna element and provides good results in situations where signal strengths vary considerably. In using the matrix pencil algorithm to estimate the directions of arrival, the examples show that the proposed method results in significantly lower bias than the traditional open circuit method. The analysis of mutual coupling is also applied in the context of a code division multiple access communication system.     

On-demand learning for a wireless campus

The current Internet and wireless networks are harsh environments for transporting high-bandwidth multimedia data. We examine the technical issues involved, and describe an end-to-end solution to support a Web-based learn-on-demand system that operates in a wireless campus environment.     

Critical thickness of GaAs/InGaAs and AlGaAs/GaAsP strained quantum wells grown by organometallic chemical vapor deposition

In this paper we describe a study of strained quantum wells (QWs) as a means to experimentally observe the critical thickness (h _c) for the formation of interfacial misfit dislocations. Two material systems were investigated: GaAs/In_0.11Ga_0.89As, in which the QW layers are under biaxialcompression, and Al_0.35Ga_0.65As/GaAs_0.82P_0.18, in which the QW layers are under biaxialtension. Samples were grown by atmospheric pressure organometallic chemical vapor deposition, and characterized by low-temperature photoluminescence (PL), x-ray diffraction, optical microscopy, and Hall measurements. For both material systems, the observed onset of dislocation formation agrees well with the force-balance model assuming a double-kink mechanism. However, overall results indicate that the relaxation is inhomogeneous. Annealing at 800–850° C had no significant effect on the PL spectra, signifying that even layers that have exceededh _c and have undergone partial relaxation are thermodynamically stable against further dislocation propagation.     

Calculation of third order intermodulation spectrum

A fast method for calculating the third order intermodulation spectrum by convolution of the input power spectrum using the FFT method is presented. The computation time is reduced to seconds even for large numbers of carriers. The computation time is insensitive to the number of different carrier types (level and bandwidth).<>     

Generalized correlation-delay-shift-keying scheme for noncoherent chaos-based communication systems

In this paper, we propose a generalized correlation-delay-shift-keying (GCDSK) scheme for noncoherent chaos-based communications. In the proposed scheme, several delayed versions of a chaotic signal are first produced. Some of them will be modulated by the binary data to be transmitted. The delayed signals will then be added to the original chaotic signal and transmitted. At the receiver, a simple correlator-type detector is employed to decode the binary symbols. The approximate bit error rate (BER) of the GCDSK scheme is derived analytically based on Gaussian approximation. Simulations are performed and compared with the noncoherent correlation-delay-shift-keying (CDSK) and differential chaos-shift-keying (DCSK) modulation schemes. The effects of the spreading factor, length of delay, and the number of delay units on the BER are fully studied. It is found that GCDSK can achieve better BER performance than DCSK under reasonable bit-energy-to-noise-power-spectral-density ratios.     

Dynamic imaging and tracer kinetic modeling for emission tomography using rotating detectors

When performing dynamic studies using emission tomography the tracer distribution changes during acquisition of a single set of projections. This is particularly true for some positron emission tomography (PET) systems which, like single photon emission computed tomography (SPECT), acquire data over a limited angle at any time, with full projections obtained by rotation of the detectors. In this paper, an approach is proposed for processing data from these systems, applicable to either PET or SPECT. A method of interpolation, based on overlapped parabolas, is used to obtain an estimate of the total counts in each pixel of the projections for each required frame-interval, which is the total time to acquire a single complete set of projections necessary for reconstruction. The resultant projections are reconstructed using traditional filtered backprojection (FBP) and tracer kinetic parameters are estimated using a method which relies on counts integrated over the frame-interval rather than instantaneous values. Simulated data were used to illustrate the technique's capabilities with noise levels typical of those encountered in either PET or SPECT. Dynamic datasets were constructed, based on kinetic parameters for fluoro-deoxy-glucose (FDG) and use of either a full ring detector or rotating detector acquisition. For the rotating detector, use of the interpolation scheme provided reconstructed dynamic images with reduced artefacts compared to unprocessed data or use of linear interpolation. Estimates for the metabolic rate of glucose had similar bias to those obtained from a full ring detector.     

Pass-transistor adiabatic logic with NMOS pull-down configuration

A new low power adiabatic logic family, pass-transistor adiabatic logic with NMOS pull-down configuration, is presented. For a 2:1 multiplexer, a power saving of ~800% is achieved, compared to a 2N-2N2P logic circuit at 20 MHz. Compared to pass-transistor adiabatic logic using single power-clock supply (PAL), the `tri-state' problem is solved, while power consumption is comparable. A four phase sinusoidal clock power supply is employed in the new logic family, which facilitates pipelining hence leading to higher throughput, compared to PAL     

Transient analysis of microwave active circuits based ontime-domain characteristic models

A modular method is presented to speed up transient simulation of microwave active circuits which consist of linear components and active devices that are often nonlinear. Firstly, the linear components and active devices are individually characterized by time-domain characteristic models (TDCM's) and lumped equivalent circuits, respectively, to reduce the computer memory. Then, based on deconvolution, the TDCM's of linear components are synthesized from the terminal voltages and currents of step voltage excitation, which are simulated by the finite-difference time-domain (FDTD) method. Finally, transient analysis of a one-dimensional (1-D) discrete-time system is applied to obtain the terminal responses of the microwave active circuits, in which a larger sampled step is chosen to reduce the simulation time. This method is employed to two realistic circuits to validate its efficiency and accuracy. The results are in good agreement with the time-consuming direct FDTD simulation of entire circuits     

Investigation of optical losses in photoelastic and ridge waveguides in GaAs-AlGaAs heterostructures

Two approaches have been used to fabricate stable photoelastic waveguides with planarized surfaces on GaAs-AlGaAs heterostructures. The first approach uses tensile Ni/sub 3/GaAs stressors formed by metal-semiconductor reactions. The second approach uses inert, refractory and compressive stressors, such as RF sputtered W and RF co-sputtered WNi films. For comparison purposes, ridge waveguides have also been fabricated using the same heterostructure by a dry etching technique. Optical losses of photoelastic waveguides, measured by Fabry-Perot (FP) method at a wavelength of 1.53 /spl mu/m, are comparable to or better than those of the ridge waveguides. Material loss appears to be the primary loss mechanism in both photoelastic and ridge waveguides. These results indicate that the photoelastic waveguide processing technique reported in this study is a promising alternative to commonly used dry etching techniques for planarization.     

Design of dual-polarized L-probe patch antenna arrays with high isolation

An experimental study of a dual-polarized L-probe patch antenna is presented. The antenna is designed to operate at around 1.8 GHz. A "dual-feed" technique is introduced to achieve high isolation between two input ports. The proposed antenna has an impedance bandwidth of 23.8% (SWR/spl les/2), 15% (SWR/spl les/1.5) and an isolation over 30 dB. In array designs, techniques for improving the isolation between two adjacent elements of an antenna array are also investigated. A two-element array with more than 30 dB isolation is designed and tested.