Dielectric Dispersion of Polycrystalline Aluminum Nitride at Microwave Frequencies

Complex permittivity of polycrystalline AlN was measured over the frequency range 100 MHz to 13 GHz using reflection coefficient and cavity resonator methods. Dielectric relaxation peaks of loss tangent were observed in the frequency range 200 MHz to 3 GHz. The maximum value of loss tangent was ∼200 × 10⁻⁴. Relative permittivities decreased by ∼4% with increased frequency at the region of relaxation peaks. It was shown that these dispersion frequencies were inversely proportional to the grain sizes of AlN and independent of purities and processes. Model calculations for elastic vibration of a single-crystal grain of AlN were performed to investigate the origin of the dielectric dispersion due to piezoelectric effect. The calculated results of elastic sphere and 14-faced-polyhedron models showed a good quantitative agreement with the observed dispersion frequencies, which suggested that the dispersion was due to a piezoelectric vibration of a single grain of AlN ceramics at microwave frequencies.     

Linking sanitation and wastewater treatment: from evaluation on the basis of effluent pollutant concentrations to evaluation on the basis of pollutant removal efficiencies

The evaluation of centralised wastewater treatment plants (WWTPs) in planning and management is sometimes based solely on effluent pollutant concentrations or pollutant loads. For sanitation purposes, the effluent pollutant concentrations/loads of WWTPs are important; of course, but from the point of view of wastewater treatment, the pollutant removal performance should also be evaluated. Focussing on low- and middle-income countries, especially those in tropical regions, published kinetics studies on biological WWTPs (such as oxidation ditches and aerated lagoons) are summarised in this paper. In most studies, effluent pollutant concentrations/loads are described as first-order linear functions of influent pollutant concentrations/loads. Therefore, pollutant removal efficiencies can be expressed as first-order linear functions of the reciprocal of influent pollutant concentrations/loads with negative coefficients. This implies that pollutant removal efficiencies increase with influent pollutant concentration/load increases. Based on pollutant removal efficiency functions, biological or ecological WWTPs when operating with small influent pollutant concentrations/loads should change their management to increase influent pollutant concentrations/loads in order to increase pollutant removal efficiencies. It may, however, be possible for technological development in wastewater treatment to overcome this problem.     

粒子网格混合方法模拟液滴夹带起始点

环状流动的特性对反应堆事故工况分析具有重要意义,本研究基于粒子网格混合方法对这一现象中的液滴夹带起始点问题进行了数值分析,利用网格求解流场,利用粒子模拟液膜及液滴的运动,探讨了气水流动大密度比情况下,不同流动方向,不同流体粘度,不同液膜厚度下的液滴夹带所需的临界气相流速,结果同经典关系式进行了对比,吻合良好．这一方法对于反应堆事故中的两相流动研究具有参考意义．     

Enhanced dielectric properties of bismuth titanate/silver composites

Bismuth titanate (BiT) based composites containing silver particles are fabricated by a solution chemical process. Incorporation of silver particles does not result in unwanted reaction phase. SEM micrographs reveal fine silver particles distribute at BiT grain boundaries and into larger BiT plate-like grains. With the addition of silver, the dielectric constant increases up to ∼10 times higher than that of pure BiT ceramic, which can be attributed to the effective electric fields developed around the dispersed metal particles and the percolation effect. Additionally, the dielectric losses are significantly reduced by incorporating silver particles, and the values of BiT/Ag composites are lower than 0.5%. The dielectric properties of BiT/Ag composites are nearly frequency independent in the measured frequency range (1 kHz to 1 MHz).     

Heat regulating strategy in numerical control end milling for hard metal machining

The trend in die/mold manufacturing at present is towards the hard machining at high speed to replace the electron discharge machining. Failure forms of the A1TiN-coated micro-grain carbide endmill when used for the machining of/IS SKD61 (HRC 53), a widely used material in die/mold manufacturing, are investigated. The endmill shows a characteristic that tool life decreases greatly due to the chipping when overload occurs or the rapid increase of wear when over-heat accumulation in cutting edges. As a consequence of the investigation, a strategy to regulate heat generation in the end milling process is proposed. This is accomplished by controlling the cutting arc length, i.e. the length of each flute engaging workpiece in a cutting cycle. Case studies on the slot end milling and comer rounding are conducted. The results show that the proposed strategy suggests the optimal tool path as well as the optimal pitch between successive tool paths under the cutting time criterion.     

Further study on different dopings into PbWO4 single crystals to increase the scintillation light yield

Since we presented our preliminary result (Nucl. Instr. and Meth. A 486 (2002) 170) at SCINT2001, we have continued our efforts to increase the light yield (LY) of PbWO₄ scintillators by extending different dopings with an aim to find a possibility of using PbWO₄ successfully in Positron Emission Tomography (PET). Overall result obtained for single doping as well as double and tripple co-dopings are summarized, including decay characteristics and radiation hardness. The LY in non-doped PbWO₄ crystals with a size of 10×10×(20–30) mm³ is 25–35 photolectrons/MeV (phe/MeV) corresponding to 3–4% of the LY in BGO, when measured with a bialkali photomultiplier during a gate of 1 μs. The maximum LY increased to 49 phe/MeV for single doping with Mo⁶⁺, 80 phe/MeV for double co-doping of Mo⁶⁺+Sb⁵⁺, and 85 phe/MeV for tripple co-doping of Mo⁶⁺+Cd²⁺+Sb⁵⁺. The radiation hardness is larger than 10⁵ Gy for each of the samples co-doped with Mo⁶⁺+Sb⁵⁺ and Mo⁶⁺+Cd²⁺+Sb⁵⁺, while it is much poorer in PWO:Mo⁶⁺. In each of these co-doped samples, a medium-speed green emission in the microsecond range is created besides the fundamental fast (a few nanoseconds range) blue one, giving a peak at 500 nm in the radioluminescence spectrum similarly as in PWO:Mo⁶⁺.     

Structural approach to nanoscience: a case study of complex and cluster formation in ZnBr2–ZnCl2 melts

Although the melt structure of glass-forming ZnCl₂ has so far been well studied, there exists quite little information on the structural change due to anion-substitution. In the present work, the short-range structure of ZnCl₂–ZnBr₂ mixture melts was analyzed systematically by time-of-flight pulsed neutron diffraction techniques, Raman spectroscopy, molecular orbital calculations, and molecular dynamics simulations. According to radial distribution analysis, it was found that there were tetrahedral structural units of ligand-substituted [ZnCl_nBr_4−n]²⁻ (n=0–4) in these melts, not implying the simple mixing of [ZnCl₄]²⁻ and [ZnBr₄]²⁻ units. Further detailed estimation indicated that the ligand-substituted complex anions were linked with each other by sharing a common anion.     

A Study of the Effect of Aluminium on the Mechanochemical Reduction of Hematite by Graphite

The effect of addition of small amounts of aluminium on mechano‐chemical reduction of hematite by graphite was studied. Various amounts of aluminium (0 to 10%) were added to a hematite‐graphite mixture, in which C/O ratio was 1:1. The hematite‐graphite‐aluminium mixtures were then subjected to ball milling followed by heating up reduction. The heating up reduction was carried out in Ar atmosphere, using TG‐DTA device. In TG‐DTA experiments, samples were heated by a constant heating rate of 10 °C/min from room temperature up to 1100 °C and maintained for 30 minutes at this temperature. To clarify the reactions which took place during milling and heating up reduction, the samples were subjected to XRD examinations. It was found that the heat generated during exothermic reaction of aluminothermic reduction of hematite promoted the endothermic reaction of carbothermic reduction. In the course of heating up reduction, the carbothermic reaction occurred just after aluminothermic reaction. Increasing of aluminum content from 0 to 10% in 2 hours ball milled samples decreased the temperature of carbothermic reaction from 1020 °C to about 860 °C. The further ball milling of the samples up to 5 and 10 hours, for the samples containing 10 and 5% aluminium respectively, caused the decrease of the temperature of aluminothermic and carbothermic reactions to around the melting point of aluminium.     

Three-dimensional rainbow schlieren measurements in underexpanded sonic jets from axisymmetric convergent nozzles

The rainbow schlieren deflectometry has been combined with the computed tomography to obtain three-dimensional density fields of shock containing free jets and we call the method the schlieren CT. Experiments on the schlieren CT have been performed at a nozzle pressure ratio of 4.0 by using an axisymmetric convergent nozzle with an inner diameter of 10 mm at the exit where the nozzle was operated at an underexpanded condition. Multidirectional rainbow schlieren pictures of an underexpanded sonic jet can be acquired by rotating the nozzle about its longitudinal axis in equal angular intervals and the three-dimensional density fields are reconstructed by the schlieren CT. The validity of the schlieren CT is verified by a comparison with the density fields reconstructed by the Abel inversion method. As a result, it is found that excellent quantitative agreement is reached between the three-dimensional jet density fields reconstructed from both methods.