Detection of back-side pit on a ferrous plate by magnetic flux leakage method with analyzing magnetic field vector

We have developed a magnetic flux leakage (MFL) system using magnetic resistive (MR) sensors for detecting two dimensional magnetic field components, and an induction coil that generates low magnetic field strengths and extremely low frequencies. The signal at each scanned measurement point (i) was divided by the signal strength M_mes,i and phase α_i by a lock-in amplifier. Using the strength M_mes,i and phase α_i, we calculated the imaginary part of the signal using the common phase β. By optimization of the common phase β to the imaginary part, the analyzed scanning data curve was shown to be effective in estimating the size (depth and diameter) of back-side pits on a ferrous plate. Comparing the two dimensional magnetic field components of leakage, the imaginary part of the y-component parallel to the induced magnetic field was found to be suitable for detecting the back-side pits.     

Optical Amplification at 1.3 μm in a Praseodymium-Doped Sulfide-Glass Fiber

Praseodymium-doped glasses were prepared in the Ga-Na-S (GNS) system and their optical properties were studied. A single-mode fiber with an attenuation loss of 1.2 dB/m at a wavelength of 1.31 μm was fabricated using an extrusion method, and the amplification characteristics were measured in the bidirectional pumping configuration. We demonstrated a gain coefficient of 0.81 dB/mW at a wavelength of 1.34 μm, which is the highest we have ever reported, and achieved a net gain of 32 dB for a pump power of 90 mW. Highly efficient optical amplification at a wavelength of 1.3 μm was demonstrated in the praseodymium-doped GNS fiber.     

中空球状水铝英石/SBR纳米复合材料的制备与性能研究

将天然中空球状水铝英石在水中进行提纯分散处理,采用乳液共混共凝法制备中空球状水铝英石/SBR纳米复合材料,并对其性能进行研究.场发射环境扫描电子显微镜和透射电子显微镜观察表明,中空球状水铝英石原矿粉以聚集体形式存在,聚集体直径约为200 nm,组成聚集体的中空球状小颗粒直径约为13 nm;水铝英石在复合材料中分散良好.与采用直接共混法制备的复合材料相比,采用乳液共混共凝法制备的复合材料定伸应力较小,拉伸强度较大.     

Potato and soy peptides alter caecal fermentation and reduce serum non‐HDL cholesterol in rats fed cholesterol

We examined the effect of potato peptides (PPC) in rats fed a cholesterol‐enriched diet, in comparison with two cholesterol‐enriched diets containing soy peptides (SPC) or casein (CNC), and a cholesterol‐free diet containing casein (CN) for 4 weeks. The serum non‐high‐density lipoprotein (HDL) cholesterol level was lower in the PPC‐ (–18.39%) and SPC‐fed (–32.76%) groups (p <0.05) than in the CNC‐fed group at the end of the feeding period. The low‐density lipoprotein receptor mRNA level in the PPC‐fed group, and cholesterol 7α‐hydroxylase and scavenger receptor class B type 1 mRNA levels in the SPC‐fed group, were higher (p <0.05) than in the CN‐ and CNC‐fed groups. Faecal neutral sterol and caecal short‐chain fatty acid concentrations in the PPC‐ and SPC‐fed groups were higher (p <0.05) than in the CN‐ and CNC‐fed groups. The faecal total acidic sterol concentration was higher in the SPC‐fed group than in the CN‐ and PPC‐fed groups. Caecal anaerobe and Bifidobacterium populations were higher (p <0.05) in the PPC‐ and SPC‐fed groups than in the CN‐fed group. This study suggests that potato peptides, as soy peptides, alter caecal fermentation and steroid absorption and reduce the serum non‐HDL cholesterol level in rats fed cholesterol.     

Strength of spline joints assembled by forming

In this paper, a new assembling method of spline joints that enables tight fitting in a simple manner by allowing slight plastic deformation at the spline teeth was introduced. Experiments were carried out for the spline joints of medium carbon steel varying the overlap zone between the male and the female spline teeth. Axial joining strength was increased with increase in the overlap length due to the residual compressive stress by forming. The joint by the proposed method also showed higher torsional strength than the conventional joint. Improvement in the torsional strength was explained based on the deformation and hardness distribution around the spline teeth. With respect to the shape of overlap zone, better results were obtained when using the specimen having a uniform overlap length along the axial direction.     

Effects of polyglycerol esters of fatty acids and ethylene‐vinyl acetate co‐polymer on crystallization behavior of biodiesel

Biodiesel fuels (BDF) have many problems in the cold due to their crystallization properties. In particular, precipitation of large crystals of high‐melting fractions in BDF at low temperatures remarkably changes cold flow property of BDF and, thereby, it increases the values of cold filter plugging point. In this study, we evaluated polyglycerol esters of fatty acids (PGE) and ethylene‐vinyl acetate co‐polymer (EVA) as chemical additives to improve the cold flow property of palm oil‐based FAME (PFME). The results of solid fat content measurement indicate that the simultaneous addition of PGE and EVA showed synergistic effects on suppression of crystallization of PFME, however such effect was not observed when EVA was used alone. DSC thermograms indicated that the PGE additives not only decreased the crystallization temperature but also kinetically suppressed the crystal growth. Polarized light microscopy showed that the simultaneous addition of PGE and EVA led to the formation of considerably small and fine‐dispersed crystals of PFME. These results indicate that combined effects of PGE and EVA caused the formation of fine‐dispersed PFME crystals, which could improve the viscous properties of palm oil‐based BDF at relatively cold temperatures.     

Comparisons of Two Models for the Simulation of a DC Arc Plasma Torch

The hypothesis of local thermal equilibrium (LTE) in thermal plasma has been widely accepted. Most of the simulation models for the arc plasma torch are based on the hypothesis of LTE and its results indicate good validity to mimic the pattern of plasma flow inside a plasma torch. However, according to the LTE hypothesis, electrical conductivity near electrodes is significantly lower because of the low gas temperature. Consequently, it is difficult for electrical current flows to pass between the anode and cathode. Therefore, the key subject for a model concentrating on the LTE assumption is to deal with the low electrical conductivity near the electrodes. In this study, two models determining the electrical conductivity at the vicinity of the electrodes with two different assumptions were used to calculate the flow patterns inside a non-transferred DC arc plasma torch. Gas temperature, velocity, voltage drop, and heat energy of the plasma arc were compared between the two models. The results indicated that the plasma arc inside the plasma torch fluctuates, as simulated by both models. It seems that the model can obtain comparable accuracy with the experimental results if the plasma gas electrical conductivity is determined by nominal electron temperature.     

The activation of furfuryl alcohol polymerization by oxygen and its enhanced mechanical properties

The effect of oxygen and additional oxygen providers on furfuryl alcohol polymerization was investigated through chemical analyses and mechanical evaluation. NMR, UV–vis, Fourier transform infrared, and gas chromatography–mass spectrometry (GC–MS) results suggested that atmospheric oxygen and the further addition of an oxygen source functioned as an activator for the entire network polymerization. Interestingly, the construction of a conjugated structure on the furan linear chain, which is key to three-dimensional cross-linking, also appears to be accelerated in the presence of oxygen. Furthermore, the introduction of oxygen providers into the curing system successfully enhanced the mechanical properties of the cured furan resin.     

Observation of non-chemical equilibrium effect on Ar-CO2-H2 thermal plasma model by changing pressure

The authors developed a two-dimensional one-temperature chemical non-equilibrium (1T-NCE) model of Ar-CO₂-H₂ inductively coupled thermal plasmas (ICTP) to investigate the effect of pressure variation. The basic concept of one-temperature model is the assumption and treatment of the same energy conservation equation for electrons and heavy particles. The energy conservation equations consider reaction heat effects and energy transfer among the species produced as well as enthalpy flow resulting from diffusion. Assuming twenty two (22) different particles in this model and by solving mass conservation equations for each particle, considering diffusion, convection and net production terms resulting from hundred and ninety eight (198) chemical reactions, chemical non-equilibrium effects were taken into account. Transport and thermodynamic properties of Ar-CO₂-H₂ thermal plasmas were self-consistently calculated using the first-order approximation of the Chapman-Enskog method. Finally results obtained at atmospheric pressure (760 Torr) and at reduced pressure (500, 300 Torr) were compared with results from one-temperature chemical equilibrium (1T-CE) model. And of course, this comparison supported discussion of chemical non-equilibrium effects in the inductively coupled thermal plasmas (ICTP).