随机减量技术中周期激励的影响及消除方法

本文针对机械系统中通常存在确定性周期激励的事实 ,论证了周期干扰成分的存在对提取的随机减量特征信号的影响 ,基于数字滤波技术提出了一种从周期干扰环境中提取随机减量特征信号的简便方法。在回转机械稳定性监测中的应用实例表明本文提出的方法是有效的。     

连续油管技术与装备发展综述

自世界上第一台连续油管作业机问世至今,连续油管作业技术与装备已经过了40多年的发展历程,以其占地面积小、作业成本低、搬迁安装方便、保护油层、增加油井产量和使用范围广等诸多不可比拟的优势,得到迅速发展,并广泛应用于钻井、完井、试油、采油、修井和集输等各个作业领域。实践表明,连续油管作业技术与装备是一项具有巨大潜力和生命力的实用性技术。目前,该项技术的应用日趋活跃,备受关注。在总结连续油管作业技术与装备的发展现状和展示其发展趋势的基础上,客观地分析了国内连续油管技术与装备的应用与研究现状,提出相应的发展对策。     

Flash器件中氧化硅/氮化硅/氧化硅的特性

对普遍采用的氧化硅/氮化硅/氧化硅( ONO)三层复合结构介质层的制备工艺及特性进行了研究分析,研究了ONO的漏电特性以及顶氧( top oxide)和底氧( bottom oxide)的厚度对ONO层漏电的影响.结果表明,采用较薄的底氧和较厚的顶氧,既能保证较高的临界电场强度,又能获得较薄的等效氧化层厚度,提高耦合率,降低编程电压.     

Estimating crystallinity in high density polyethylene fibers using online Raman spectroscopy

Online Raman spectra, obtained at different points along the spin line during pilot‐scale nonisothermal melt spinning of high density polyethylene (HDPE) fibers, are presented for the first time. The fraction of the crystalline phase corresponding to each spectrum was determined from the normalized integrated intensity of the 1418 cm^?1 Raman band. It is well established that this band represents the orthorhombic crystalline phase in polyethylene. The estimates of percent crystallinity obtained from decomposition of the Raman spectrum were compared with the percent crystallinity from differential scanning calorimetry (DSC) measurements. It is concluded that online Raman spectroscopy can be successfully used to monitor the development of crystallinity in HDPE fibers as a function of distance from the spinneret. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 545–549, 2003     

Magnetic Properties of Fe-Doped Rutile

Ball-milling method was applied to dissolve Fe into titanium dioxide (TiO₂). X-ray diffraction indicated the starting anatase changed to a rutile-type structure with oxygen deficiency after ball milling. Transmission electron microscopy and X-ray absorption experiments were conducted to examine the possible existence of magnetic impurities in the ball-milled powders after they were leached in HCl solutions. Temperature dependence of the resistivity shows semiconducting behavior and the magnetic hysteresis loops at 5 and 300 K exhibit ferromagnetic characteristics. Fe-doped TiO₂ films were also prepared by pulsed laser deposition. The magnetic properties of the films are discussed.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

一种改进的MC-CDMA系统结构

MC-CDMA在频域扩频时实际上是一种频率分集,对于频率分集重数的要求通常小于子载波的数目N,故扩频因子可以小于子载波数目。改进了这种MC-CDMA系统的结构,通过在频域引入交织器,使交织后频率分集各分量经历独立的哀落,从而提高了抗哀落能力。最后给出了用系统仿真软件SPW仿真的结果。