Microstructure of Aluminum/Glass Joint Bonded by Ultrasonic Wire Welding

An Al/glass joint created by using ultrasonic welding was analyzed by means of multiscale observation techniques. A cross-sectional analysis of the microstructure revealed that a directly joined interface without reaction phases formed at the periphery of a round joined region. The size of Al grains markedly decreased after ultrasonic welding and some subgrains were observed along the interface. The finer Al grains observed around the periphery of the joined interface showed active plastic flow that promoted welding.     

Finite Element Analysis of Precursors to Macroscopic Stick–Slip Motion in Elastic Materials: Analysis of Friction Test as a Boundary Value Problem

In this study, we apply the finite element method to investigate precursor to frictional sliding phenomena arising immediately prior to macroscopic stick–slip transitions in elastic bodies within the framework of a continuum theory. Using a numerical model that mimics an actual experimental system, we study the behavior of contact surface nodes to assess the influence of stiffness, driving velocity, initial conditions, and discretization conditions on the propagation characteristics of microscopic slips. In particular, we show that the initial distribution of frictional stress arising due to the Poisson effect has a significant effect on the propagation characteristics in slip regions. Next, based on the results of a finite element analysis of precursor phenomena that accounts for the influence of bulk compliance, we consider the determination of parameters in rate-dependent friction models. With regard to the behavior of sliding friction, we show that the relationship between friction tests and friction models is fundamentally different from the relationship between material tests and constitutive models for material deformation. We conclude that a proper understanding and classification of friction tests, friction models, and the relationship between these tests and boundary value problems are crucial ingredients in the application of computer-aided engineering techniques to sliding-friction phenomena; indeed, friction tests must ultimately be treated as boundary value problems.     

污水处理排放水对小流量河流水体生态的影响

针对日本国鬼怒河流域小流量河流,通过对河床上附着生物膜的组成、底栖生物、细菌活性分析和AGP试验,研究了污水厂二级处理排放水对小流量河流生态的影响.研究表明,当污水厂二级处理排放水占河流流量比例较大时(研究河流所占比例为35%),同样会引发河流富营养化和影响河流水体的生态.因此,从保护水环境及其生态考虑,有必要对污水进行深度处理.     

A novel experimental technique to determine the heat transfer coefficient between the bed and particles in a downer

A novel method for directly measuring the temperature history of mobile hot ferromagnetic particles (steel particles), substituting for reacting particles, in a binary-solid (reacting particles and inert particles) downflow is introduced. The temperature history of the hot steel particles can be obtained by measuring the temperature of the particles at different axial positions using magnetic fields that can separate the steel particles from other bed materials immediately and easily. Employing the magnetic marking method, magnetic sensors were used to detect the change in magnetic flux density in a given magnetic field, and the residence time of the steel particles was also measured. The cross-sectional averaged particle-to-bed heat transfer coefficients were calculated from the experimental results using simple heat balance equations. The measured temperature data have a relatively wide error range; however, the average temperature curves derived from the average particle-to-bed heat transfer coefficients agreed with the temperature plots. Therefore, the experimental method of this study is applicable to the measurement of the particle temperature in a binary-solid downflow. The results showed that there is strong correlation between the particle-to-bed heat transfer coefficients and normalized collision frequency under the laminar gas flow conditions.     

X100试验管线钢管的规范和生产

介绍了位于英国诺林伯利亚,钢管直径1 219 mm(48 in),输气压力18 MPa(180 bar),由英国BP公司承建的X100试验管线的建设概况.根据X100试验管线的设计参数制定了相应的钢管规范,设计了X100管线钢管母材、焊缝金属和热影响区的合金成分.按设计的合金成分由住友金属鹿岛钢铁厂生产了钢材、钢板,并...     

InxGa1−xAs ohmic contacts to n-type GaAs with a tungsten nitride barrier

Significant reduction of the contact resistance of In_0.7Ga_0.3As/Ni/W contacts (which were previously developed by sputtering in our laboratory) was achieved by depositing a W₂N barrier layer between the Ni layer and W layer. The In_0.7Ga_0.3 As/Ni/W₂N/W contact prepared by the radio-frequency sputtering technique showed the lowest contact resistance of 0.2 Ωmm after annealing at 550°C for 10 s. This contact also provided a smooth surface, good reproducibility, and excellent thermal stability at 400°C. The polycrystalline W₂N layer was found to suppress the In diffusion to the contact surface, leading to improvement of the surface morphology and an increase in the total area of the In_xGa−As between metal and the GaAs substrate. These improvements are believed to reduce the contact resistance.     

Hot carrier magnetophonon spectroscopy of semiconductors in high magnetic fields up to 40 T

Hot carrier magnetophonon resonances of n-type Si, short channel InP and p-type InSb were investigated in pulsed high magnetic fields up to 40 T. Using a recently developed high resolution technique in pulsed high fields, many new features of the hot carrier-phonon interactions in high magnetic fields were found.     

Water quality characteristics of rivers and ponds in Japan

In Japan, various countermeasures have been taken to improve the water quality of public waters such as rivers and lakes. Though water quality has improved, it is still insufficient. In summer, eutrophication is seen in lakes and inner bays, as well as rivers. As a countermeasure to prevent eutrophication, the removal treatment of nutrient salts such as nitrogen and phosphorus is done, in addition to organic substance elimination in the domestic sewerage system. This report will show the water quality characteristics of rivers and ponds in Japan It is considered that these investigative results are effective when the water quality improvement of the stabilization ponds where eutrophication occurs are examined in China.     

Investigation of Water Tree Degradation in Dry‐Cured and Extruded Three‐Layer (E‐E Type) 6.6‐kV Removed XLPE Cables

Dry‐cured and extruded three‐layer (E‐E type) 6.6‐kV cross‐linked polyethylene (XLPE) cables were introduced into electric power systems more than 30 years ago, but they do not experience failures because of water tree degradation. Also, the degradation index of water treeing for these cables has not been established. Therefore, investigating results of residual breakdown voltage and water tree degradation of these cables will help us plan for cable replacement and determine water tree degradation diagnosis scheduling, and will be fundamental data for cable lifetime evaluation. In this study, the authors measured the ac breakdown voltages of dry‐cured and E‐E type 6.6‐kV XLPE cables removed after 18 to 25 years of operation and observed the water trees in their XLPE insulation. As a result, it was observed that breakdown voltages were larger than the maximum operating voltage (6.9 kV) and the ac voltage for the dielectric withstanding test (10.3 kV). Water trees were mainly bow‐tie water trees and their maximum length was approximately 1 mm. Although the number of measured cables was limited, the lifetime of this type of cable was estimated to be approximately 40 years, even experiencing water immersion.     

A new methodology to guarantee the structural integrity of Al2O3/SiC composite using crack healing and a proof test

Structural ceramics are brittle and sensitive to flaws. As a result, the structural integrity of a ceramic component may be seriously affected by inherent flaws. Self-crack-healing is an excellent answer to this problem. At the moment, however, there is no technique to heal embedded flaws. Therefore, a technique to guarantee the reliability of ceramic components is demanded, and thus a technique using crack healing followed by proof test was developed by K. Ando et al. to accomplish this. With this technique, testing the mechanical behaviour of the crack-healed zone is very important for ensuring the structural integrity of a ceramic component. In this study, first Al₂O₃/SiC composite with an excellent crack-healing ability was sintered. Second, a crack was introduced on the sample (3 mm × 4 mm × 36 mm), which reduced the bending strength by about 80%, and subsequently the crack was healed. Third, a proof test was carried out on the crack-healed sample. Last, using the crack-healed and proof-tested sample, a fracture test was carried out up to 1373 K. The measured minimum fracture stress (σ_Fmin) was compared with the theoretical minimum strength (σ_G) from room temperature (R.T.) to 1373 K. It was concluded that σ_G showed good agreement with σ_Fmin up to 1373 K and that the crack healing followed by proof test was an excellent technique to increase the survival probability by administering a proof test and to guarantee the reliability of Al₂O₃/SiC composite.