Air entrainment in fresh concrete with PFA

The results of a study into the influence of PFA on air entrainment in fresh concrete are discussed It is shown that the required dosage of AEA to produce an air content of 5.5 ± 0.5% in a PFA modified concrete mix is two-six times that required in the corresponding neat OPC concrete mix. The dosage of a vinsol based air entraining agent (AEA) required appears to be directly related to the PFA content of the mix. Similar direct relationships were obtained with a range of different PFAs. The dosage of an AEA based on the salt of a fatty acid appears to be sensitive to both PFA and OPC contents. For the type of PFA used, the variability of measured air content or the amount of air retained after continued agitation both indicated that vinsol based AEAs show the highest variability whilst fatty acid based AEAs show low variability. The between batch variability of air content was significantly improved by the addition of PFA regardless of the AEA used.     

Fluorimetric methods for the measurement of intermediate metabolites (lactate,pyruvate, alanine, β-hydroxybutyrate,glycerol) using a COBAS FARA centrifugal analyser

Intermediate products of the metabolism of glucose, fat and amino-acid are important in the evaluation of such metabolic disorders as diabetes mellitus, liver disease and metabolic acidosis. In the present study, methods for the measurement of intermediate metabolites (lactate, pyruvate, alanine, β-hydroxybutyrate and glycerol) have been adapted to a fast centrifugal analyzer: the COBAS FARA. Correlation coeffcients rangedfrom 0.90 to 0.99, compared to established manual spectrophotometric methods. Within-run coeffcients of variation (CVs) ranged between 2.9 and 8.8% at low levels, between 1.5 and 5.7% at medium levels and between 1.2 and 5.6% at high levels. Between-run CVs were between 4.0 and 15.0% at low levels, between 1.7 and 7.0% at medium levels and between 1.3 and 2.7% at high levels. These fluorimetric assays for the determination of intermediate metabolites on COBAS FARA (Roche) have a good sensitivity and precision, are less costly than manual methods and can be used on a routine basis.     

Three-node, 40 Gbit/s OTDM network experiment using electro-opticswitches

The authors demonstrate, for the first time, a three node optically time division multiplexed network with a maximum capacity of 40 Gbit/s. Electro-optical switches were used for both `drop and insert' and demultiplexing, and electronic clock recovery provided synchronisation throughout the network     

Biophysical aspects of gas bubbles in blood

The widespread use of bubble oxygenators during cardiopulmonary bypass has raised questions concerning the production and introduction of gaseous microemboli (GME) into patients. An understanding of the complications associated with GME requires awareness of the biophysical and biochemical responses that occur between bubbles and blood. The production of GME as well as their interactions with each other and with blood products are examined. These interactions can influence the data collected from Doppler ultrasound devices and the development of organ dysfunction.     

Study of etch rate characteristics of SF6/He plasmas byresponse-surface methodology: effects of interelectrode spacing

The characteristics of SF₆/He plasmas which are used to etch Si₃N₄ have been examined with experimental design and modeled empirically by response-surface methodology using a Lam Research Autoetch 480 single-wafer system. The effects of variations of process gas flow rate (20-380 sccm), reactor pressure (300-900 mtorr). RF power (50-450 W at 13.56 MHz), and interelectrode spacing (8-25 mm) on the etch rates of LPCVD (low-pressure chemical vapor deposition) Si₃N₄, thermal SiO₂, and photoresist were examined at 22±2°C. Whereas the etch rate of photoresist increases with interelectrode spacing between 8 and 19 mm and then declines between 19 and 25 mm, the etch rate of Si₃N ₄ increases smoothly from 8 to 25 mm, while the etch rate of thermal SiO₂ shows no dependence on spacing between 8 and 25 mm. The etch rates of all three films decrease with increasing reactor pressure. Contour plots of the response surfaces for etch rate and etch uniformity of Si₃N₄ as a function of spacing and flow rate at constant RF power (250 W) display complex behavior at fixed reactor pressures. A satisfactory balance of etch rate and etch uniformity for Si₃N₄ is predicted at low reactor pressure (~300 mtorr), large electrode spacing (12-25 mm), and moderate process gas flow rates (20-250 sccm)     

Construction of a concrete containment model

This paper discusses the features and construction of a reinforced-concrete containment model that has been built at Sandia National Laboratories in Albuquerque, New Mexico. The model Light-Water-Reactor (LWR) containment building was designed and built to the American Society of Mechanical Engineers (ASME) code by United Engineers and Constructors, Inc. The containment model will be tested to failure to determine its response to static internal overpressurization. The results from testing the heavily instrumented containment will be used to assess the capability of analytical methods for predicting the performance of containments subject to severe accident loads as part of the US Nuclear Regulatory Commission's program on containment integrity.The scaled dimensions of the cylindrical wall and hemispherical dome are typical of a full-size containment. Features representative of a prototypical containment and included in the heavily reinforced model are equipment hatches, personnel airlocks, several small piping penetrations, and a thin steel liner attached to the concrete by headed studs.     

Software Licensing Models: What's Out There?

As software and hardware evolve, licensing choices are becoming more complex. Understanding licensing trends and the latest models is one way to achieve the greatest return on software investment.     

United States Nuclear Regulatory Commission Research Program on molten core debris interactions in the reactor cavity

The NRC's Research Program on Core-Debris/Cavity Interactions comprises two principal elements: (1) an analytical effort focused primarily on development of computer codes needed to predict the potential consequences of risk-significant severe-accident scenarios; and (2) an experimental component to provide insights into the relevant phenomenological processes and to develop the experimental data base necessary for validation of the codes. The analytical activities at Sandia National Laboratories (SNL) focus primarily on refinement and validation of the CORCON and VANESA codes. Two major experimental activities are also based at SNL: (1) the large-scale SURC tests address the thermal-hydraulic phenomena in the cavity as well as aerosol release associated with prototypical core-melt materials in various types of concrete crucibles, while (2) the WITCH and GHOST experiments are concerned with aerosol generation and radionuclide release phenomena. A program of small-scale special-effects tests at Brookhaven National Laboratory (BNL) is coupled to a concomitant model-development and code-validation activity. In addition, measurements are being made at Battelle Columbus Laboratory (BCL) to augment the thermochemical data base needed in the VANESA code to permit refined radiological source-term predictions. The current scope and status of this research is reviewed.