Lowpass and bandpass transadmittance filter using operational amplifier pole

A new topology simultaneously implementing lowpass (LP) and bandpass (BP) transadmittance filtering signals using a single operational amplifier (OA), one capacitor, and two resistors is presented. The input impedance is very high which is essential for cascading without employment of buffers. The circuit uses absolute minimum number of active and passive components. The filter employs pole-model of OA and as such has acquired suitability for extended frequency operation. The circuit permits separate adjustment of natural frequency (ω₀) and quality factor (Q) in an orthogonal manner. The circuit has low sensitivity figures unlike the reported single amplifier biquads. The PSPICE simulation results are included.     

BN–Graphene Composites Generated by Covalent Cross‐Linking with Organic Linkers

Composites of boron nitride (BN) and carboxylated graphene are prepared for the first time using covalent cross‐linking employing the carbodiimide reaction. The BN_1–xG_x (x ≈ 0.25, 0.5, and 0.75) obtained are characterized using a variety of spectroscopic techniques and thermogravimetric analysis. The composites show composition‐dependent electrical resistivity, the resistivity decreasing with increase in graphene content. The composites exhibit microporosity and the x ≈ 0.75 composite especially exhibits satisfactory performance with high stability as an electrode in supercapacitors. The x ≈ 0.75 composite is also found to be a good electrocatalyst for the oxygen reduction reaction in fuel cells.     

A modified rain attenuation prediction model for tropical V‐band satellite earth link

Radio wave propagation plays a very important part in the design and eventually dictates performance of space communication systems. Over time, the requirements of satellite communication have grown extensively where higher capacity communications systems are needed. Escalating demands of microwave and millimetre wave communications are causing frequency spectrum congestion. Hence, existing and future satellite system operators are planning to employ frequency bands well above 10 GHz. The challenge in operating at such high frequencies for communication purposes is that there exists stronger electromagnetic interaction between the radio signals and atmospheric hydrometeors. Such instances will degrade the performance of such high frequency satellite communication systems. The development of a revised model for a better‐improved rain fade prediction of signal propagations in tropical region is considered very important. Researchers and engineers can employ the model to accurately plan the future high frequencies satellite services. Copyright © 2014 John Wiley & Sons, Ltd.     

Quantitative preparation of long chain thioethers from an oxo-trans-2-enoic ester and a 9,12-dioxo-trans-10-enoic acid

Branched-chain thioethers have been prepared from methyl 4-oxo-trans-2-hexadecenoate and 9,12-dioxo-trans-10-octadecenoic acid. The reagents involved in these preparations were mercaptoacetic and mercaptopropionic acids. The yields of these thioethers are almost quantitative.     

Industrie 4.0 Readiness: Green Computing in Relation with Key Performance Indicator for a Manufacturing Industry

Mobile Networks and Applications - An effective measure of Key Performance Indicators (KPIs) is of great significance to enhance the capabilities of a decision support system (DSS) of any...     

Carrier Transport Enhancement Mechanism in Highly Efficient Antimony Selenide Thin-Film Solar Cell

Exhibiting outstanding optoelectronic properties, antimony selenide (Sb₂Se₃) has attracted considerable interest and has been developed as a light absorber layer for thin-film solar cells over the decade. However, current state-of-the-art Sb₂Se₃ devices suffer from unsatisfactory “cliff-like” band alignment and severe interface recombination loss, which deteriorates device performance. In this study, the heterojunction interface of an Sb₂Se₃ solar cell is improved by introducing effective aluminum (Al³⁺) cation into the CdS buffer layer. Then, the energy band alignment of Sb₂Se₃/CdS:Al heterojunction is modified from a “cliff-like” structure to a “spike-like” structure. Finally, heterojunction interface engineering suppresses recombination losses and strengthens carrier transport, resulting in a high efficiency of 8.41% for the substrate-structured Sb₂Se₃ solar cell. This study proposes a facile strategy for interfacial treatment and elucidates the related carrier transport enhancement mechanism, paving a bright avenue to overcome the efficiency bottleneck of Sb₂Se₃ thin-film solar cells.     

Optical GFDM: an improved alternative candidate for indoor visible light communication

Photonic Network Communications - This paper proposes generalized frequency division multiplexing (GFDM) for indoor visible light communication (VLC). GFDM is a flexible multi-carrier scheme that...     

A routing algorithm for reducing optical loss in photonic Networks-on-Chip

Driven by increase in automation, smart homes play an important role in today’s human life. This paper presents a new model for smart home technologies based on multi-device bidirectional visible light communication (VLC). For multiple devices and users, orthogonal code-based wavelength division (color beams) full-duplexed bidirectional VLC link is proposed. The color beams from RGB LEDs are utilized to transmit data and synchronize multi-device transmission. To enhance the performance of the proposed model, receiver diversity is also employed. Performance evaluation reveals that the proposed VLC-based model for smart homes is efficient with superior BER performance in a typical smart home environment except for the far corners. The maximum achievable data rate for each user up to four users is found to be 24 Mbps at both uplink and downlink transmissions.     

Effect of wafer thinning methods towards fracture strength and topography of silicon die

This paper characterizes die damage resulting from various wafer thinning processes. Die fracture strength is measured using ball breaker test with respect to die surface finish. Further study on surface roughness and topography of each surface finish is obtained by atomic force microscopy (AFM) and scanning electron microscopy (SEM) techniques. Stress relief process with 25 μm removal is able to strengthen 100 μm wafer by 20.4% using chemical wet etch and 75 μm wafer by 36.4% with plasma etch. Relatively, plasma etching shows higher fracture strength and flexibility compared to chemical wet etch. This is due to topography of the finished surface of plasma etch is smoother and rounded, leading to a reduced stress concentration, hence improved fracture strength.     

Deployable Structures Based on Buckling of Curved Beams Upon a Rotational Input

Inspired by the recent success of buckling-induced reconfigurable structures, a new class of deployable systems that harness buckling of curved beams upon a rotational input is proposed. First, experimental and numerical methods are combined to investigate the influence of the beam's geometric parameters on its non-linear response. Then, it is shown that a wide range of deployable architectures can be realized by combining curved beams. Finally, the proposed principles are used to build deployable furniture such as tables and lamp shades that are flat/compact for transportation and storage, require simple or no assembly, and can be expanded by applying a simple rotational input.