Chitosan Microspheres as Carriers for pH‐Indicating Species in Corrosion Sensing

Chitosan microspheres containing bromocresol green, cresol red, and phenolphthalein for corrosion detection, through pH change, are synthesized in order to be used in protective coatings for aluminium alloys. Microspheres containing corrosion detection species are characterized morphologically (SEM) and physico‐chemically (FTIR, TGA). Release studies (UV–vis) are performed in corrosion‐promoting conditions (pH, NaCl), and detection studies by immersion in media associated with corrosion activity while microspheres' sensing activity is evaluated visually. Electrochemical characterization of AA2024 substrates in the presence of chitosan spheres is performed to understand material performance, and a color change is observed as a result of local pH increase in cathodic areas when corrosion takes place. These findings can be correlated with the results from release studies and seem a promising approach for corrosion sensing purposes, not only because pH increase is possible to detect due to corrosion, but also because chitosan is considered an environmentally friendly material.     

Comparison of two low-hazard organic solvents as individual and cosolvents for the fabrication of polysulfone membranes

Petroleum-derived solvents commonly used in membrane fabrication are often hazardous and toxic, so the investigation of safer alternatives is important. In this study, two low-hazard solvents, methyl 5-(dimethylamino)-2-methyl-5-oxopentanoate (Rhodiasolv® PolarClean) and gamma-valerolactone (GVL), were investigated as sole solvents and as cosolvents to cast polysulfone membranes via nonsolvent induced phase inversion. Normalized viscosity was introduced as an indicator of dope solution homogeneity and was used to compare the required time of mixing to achieve full dissolution of the polymer in the different solvents/solvent mixtures. All dope solutions made with low-hazard solvents were found to be more viscous than those made with traditional solvents, which meant additional mixing time was needed, and that fabricated membranes were morphologically different. With respect to operation, membranes cast from dope solutions containing equal amounts of PolarClean and GVL displayed the most similar flux curves and solute rejection to those made using the traditional solvent tested.     

Anisotropic thermal conductivity of silicon nitride ceramics containing carbon nanostructures

Silicon nitride (Si₃N₄) composites containing carbon nanotubes (CNTs) or graphene nanoplateles (GNPs) are of great relevance in the electronic and aerospace industries where the search for new materials with enhanced and anisotropic thermal conductivity to work in harsh environments is a strategic guideline. Here we study thermal conduction in Si₃N₄ composites with different amounts of carbon nanostructures. The effects of the nanostructure orientation respect the heat flux, the testing temperature and the α/β Si₃N₄ phase ratio are analyzed. The addition of CNTs and GNPs leads to an anisotropic thermal response, decreasing the through-thickness thermal conductivity of the Si₃N₄ composites and raising the in-plane thermal conductivity, especially for GNPs that enhance it up to twice that of the monolithic Si₃N₄. This effect is related to the preferred orientation of the nanostructures that gives a less resistive network in the in-plane direction and the intrinsic anisotropy of their thermal conductivity.     

Effects of ozonized water and heat treatment on the papaya fruit epidermis

This study examined the effects of O₃ and hot water treatments on the epidermis of Golden papaya fruit. Heat treatments were applied in a hot water brushing (HWB) system. Papayas were brushed under a pressurized hot water rinse stage at 45, 55 and 65 °C for 60 s. In the HWB treatment, 4 ppm ozone was applied to the papayas for 1 or 2 min. The results show that ozone applications did not affect the fruit's cuticular surface, while heat treatments allowed natural fissures on the fruit epidermis to recover. Several crystalloid forms were identified on the epidermis of the papayas after the heat treatments. The predominant crystalloid forms on papayas are tubular and there is a positive response to temperature; the higher the temperature, the larger and more frequent the tubular crystalloids.     

Preliminary study of the anticancer applications of mesoporous materials functionalized with the natural product betulinic acid

Dehydrated MCM-41 (S1) was functionalized under nitrogen with 3-chloropropyltriethoxysilane (CPTS) and 3-aminopropyltriethoxysilane (APTS) by grafting in toluene at 80 °C over 48 h to give the corresponding materials S2 and S3, respectively. Subsequently, S2 and S3 were suspended in methanol and reacted in a nitrogen atmosphere with betulinic acid (BA) for 48 h at 65 °C (in the presence of the triethylamine of S2) to give the BA-functionalized materials S4 and S5. All materials studied were characterized by powder X-ray diffraction, X-ray fluorescence, nitrogen gas sorption, multinuclear MAS NMR spectroscopy, thermogravimetry, UV spectroscopy, IR, SEM, and TEM. To study the release of BA, S4 and S5 were suspended in solutions simulating various body pH conditions (pH 7.4, 5.5, and 3.0). Results of the quantification of BA release by HPLC for S4 show a pH-dependent and very slow BA release following a logarithmic tendency, while S5 behaves differently, also pH-dependent but, in this case, fast release of BA which requires only days for total release of the therapeutic compound. In addition, the cytotoxic activity of all synthesized materials against various cancer cell lines was studied. The results show the absence of an antiproliferative effect on the surfaces without BA S1-S3, while an antiproliferative effect was observed with S4 and S5 and was attributed to the release of BA in the medium.