Effect of Annealing on the Surface Microstructure of Y-Ba-Cu-O Superconducting Ceramics

Precusors to the YBa₂Cu₃O_7-δ material were prepared by both the oxalate precipitation method and conventional ceramic processing. Second-phase grains were observed to develop on the exposed fracture surface during annealing at 500° to 600°C in an ambient atmosphere. The second-phase grains were identified to be BaCO₃ using EDX and XRD. The liquid phase, which was formed because of local chemical inhomogeneity in the Y-Ba-Cu-O system, contributed to the formation of second-phase grains as a source of Ba.     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

汉城旅游商务区的空间特征:以梨泰院专项旅游区为例

韩国许多城市指定了专项旅游区,通过提供若干激励政策来促进城市旅游.汉城的梨泰院1997年被指定为专项旅游区并成为CBD的一部分.本研究追溯了它作为旅游购物区的变化过程,并通过调查其土地使用找出城市空间结构的变化特征.最后,作者提出了对发展城市旅游的政策性建议,包括减少指定性区域和特殊政策.     

Experimental and analytical study on the spray characteristics of dimethyl ether (DME) and diesel fuels within a common-rail injection system in a diesel engine

This paper investigates the effect of injection parameters on the characteristics of dimethyl ether (DME) as an alternative fuel in a diesel engine with experimental and analytical models based on empirical equations. In order to study macroscopic and microscopic characteristics of DME fuel, this work focuses on the atomization characteristics of DME and compares experimental and predicted results for spray development obtained by empirical models for diesel and DME fuel. Detailed comparisons of spray tip penetration from three different empirical correlations and from visualization experiments of diesel and DME fuels were conducted under various fuel injection conditions. In comparison with the results of different empirical equations for measured spray tip penetration, the experimental results of this study provide good agreement with the calculation results based on empirical equations, except during the earliest stage of the injected spray sequence. The results of atomization characteristics indicate that DME showed better spray characteristics than conventional diesel fuel. Also, the fuel injection delay and maximum injection rate of DME fuel are shorter and lower than those of diesel fuel at the same injection conditions, respectively.     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure and processability of iodinated poly(vinyl alcohol). IV. Drawability of the films iodinated at solution before casting

The drawability of iodinated at solution before casting (IBC) polyvinyl alcohol films prepared by casting aqueous solutions of 10 wt % PVA containing 15.2, 39.8, 83.2, 117.0, and 140.1% was examined with a tensile tester at 20–60°C. The tensile behavior of IBC films showed that the yield and breaking loads were much lower, and the breaking elongation was even higher than those of the unoriented iodinated after casting (IAC) films as well as the untreated PVA films. The maximum draw ratios of the films with the weight gain of 15.2, 39.8, 83.2, 117, and 140.1% were 4.5, 5.5, 8.5, 8.0, and 7.5, respectively, which were achieved at 20°C in all. The crystallinity of all films increased by the maximum draw, regardless of crystallinity before drawing. The crystalline structure was recovered to the original PVA crystalline lattice by deiodination. Amorphous orientation and initial moduli increased with the maximum draw ratio, while the orientation of crystals was constant. The orientation and moduli increased up to the weight gain of 83.2%, whose highest draw ratio and initial modulus were 8.5 and of 7.1 GPa, respectively, and then decreased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Monoclonal antibody-based competitive ELISA for simultaneous detection of rinderpest virus and peste des petits ruminants virus antibodies

An experimental competitive enzyme-linked immunosorbent assay (morbillivirus cELISA) using a recombinant N antigen (rRPV N) expressed in a baculovirus and a ruminant morbillivirus (RPV and PPRV)-specific monoclonal antibody (P-13A9) was developed for simultaneous detection of rinderpest virus (RPV) and peste des petits ruminants virus (PPRV) antibodies and its diagnostic performance was evaluated. A set of known reference antisera against RPV and PPRV belonging to different lineages, experimental sera from cattle vaccinated for a RPV of Asian lineage, and field sera from cattle and sheep/goat populations known to be positive (West Africa) and negative (Korea) for RPV and PPRV were used for the evaluation. Morbillivirus cELISA results on the panel of experimental RPV and PPRV antisera showed high correlation (r=0.97) between the whole virus and the rRPV N antigens, suggesting that the rRPV N contains a ruminant morbillivirus-specific antigenic determinant recognized by the P-13A9 and it may be suitable as an ELISA antigen in place of the whole virus. Morbillivirus cELISA detected anti-RPV and anti-PPRV antibodies in all reference RPV and PPRV antisera containing VN titers >/=1:8, suggesting that the assay can simultaneously detect antibodies against RPV and PPRV. Anti-RPV antibody was detected by morbillivirus cELISA in vaccinated cattle as early as the VNT and continued to be detectable by both the cELISA and the VNT until termination of the study. When applied to field samples from Africa, morbillivirus cELISA showed good agreement with a RP cELISA kit (kappa value of 0.86) in bovine sera and with a peste des petits ruminant cELISA kit (kappa value of 0.81) in caprine/ovine sera. Usefulness of morbillivirus cELISA using the rRPV N protein was discussed.