A multilevel PWM strategy suitable for high‐voltage motor direct drive systems with consideration of the adverse effect of dead time

Recently, high‐voltage motor direct drive systems have been put to practical use, and various multilevel PWM strategies have also been proposed. This paper describes a multilevel PWM strategy [our group calls it the Carrier Phase Selection Method (CPS)] that has the lowest line voltage harmonic distortion in order to prevent the degradation of high‐voltage motor winding insulations. This method takes the adverse effect of dead time into consideration, and it controls the shift direction of a carrier phase. Therefore, a favorable output waveform without instantaneous voltage surges is achieved even if the line voltage level changes. Moreover, the switching transitions across all switching devices are well‐balanced, so the utilization of inverter unit cells is equalized. This is an important factor when designing the entire system. Based on simulation and experimental results, it is shown that this CPS method is particularly effective in high‐voltage motor direct drive systems. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(2): 77–88, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20474     

Morphology of nanoholes formed in silicon by wet etching in solutions containing HF and H2O2 at different concentrations using silver nanoparticles as catalysts

Holes with diameters of tens of nanometers were bored in Si(1 0 0) in aqueous solutions containing hydrofluoric acid and hydrogen peroxide utilizing silver nanoparticles as catalysts. The holes grew deeply in the [1 0 0] direction when the concentration of hydrogen peroxide was about 0.18 M. In addition to these vertical holes, holes were generated horizontal to the surface in the 〈1 0 0〉 directions near the surface of the sample. We found that the silver particles making the deep holes in the [1 0 0] direction were more spherical than those making the horizontal holes near the surface. These results indicate that the shape of the silver particles is an important factor controlling the direction of the holes. When the hydrogen peroxide concentration was increased to 1.8 M, as well as the vertical and horizontal holes, a microporous layer was formed on the top surface region. On the other hand, when the hydrogen peroxide concentration was lowered to 0.0018 M, holes did not show any preference for growing direction and were crooked. Even in HF solutions that did not contain hydrogen peroxide, holes were generated at a very slow rate in random directions if the solutions contained oxygen.     

Thermal conductivity of non-stoichiometric americium oxide: A molecular dynamics study

The aim of this paper is to investigate the influence of multi-valency of americium in its oxide for the lowering of the thermal conductivity and the uncertainty in measurement. In the present study, thermal conductivity of non-stoichiometric americium oxide was evaluated up to 2000 K by the non-equilibrium molecular dynamics calculations using the Born-Mayer-Huggins interatomic potential with the partially ionic model. The oxygen-to-americium ratio (O/Am) was varied from 1.6 to 1.9, which corresponded to the variation of the ratio of Am³⁺/Am⁴⁺. So, we prepared potential parameters for both Am³⁺ and Am⁴⁺. The calculated thermal conductivity of non-stoichiometric americium oxide decreased with an increase of temperature, and the degree of the temperature dependence became smaller with a decrease of the O/Am ratio. This was mainly caused by the phonon-scattering due to oxygen vacancies induced with Am³⁺ ions. Comparing two supercells in which (1) short-range ordered Am³⁺ clusters were contained and (2) Am³⁺ ions were randomly distributed, the thermal conductivity of the former seemed to be somewhat larger than that of the latter.     

Microstructure Control of Sintered Porous Yttria-Stabilized Zirconia as a Durable Thermal Shielding Material

The microstructure of a thermal shielding material affects its thermal conductivity and mechanical property. In this study, the effects of the sintering temperature and the polymethyl methacrylate powder as a pore-former on the microstructure of a sintered porous yttria-stabilized zirconia (YSZ), which is used as a durable thermal shielding material, were investigated. It became clear that the microstructure of the sintered YSZ could be controlled by the particle size and the amount of the pore-former and the sintering temperature. The effect of the yttria amount in the YSZ on the microstructure was also clarified.     

Adsorption of bovine serum albumin to a polymer brush prepared by atom-transfer radical polymerization in a porous inorganic membrane

Protein adsorption was performed by a polymer brush prepared by atom-transfer radical polymerization (ATRP) to a porous inorganic membrane. The porous inorganic membrane, Shirasu Porous Glass made from silica, was modified with a halogen-containing compound to bind the active species for the polymerization. Glycidyl methacrylate was polymerized from the halogen compound by ATRP for a prescribed time, and subsequently chemically modified. The progression of the chemical modification allowed the membrane to lower the phosphate-buffer flux of the porous membrane due to the attachment of the polymer brush. Bovine serum albumin (BSA), as a model protein, was adsorbed at 12 mg per gram of the membrane in permeating BSA solution through the polymer-brush-attached porous membrane.     

纳米SiO_2制备方法研究

以溶胶—凝胶法(sol-gel)为基础,乙醇作溶剂,在氨水催化作用下,研究了正硅酸乙酯(TEOS)通过水解聚合反应制备Si O2微球的方法,并探讨n(水)/n(TEOS)(简称H)及反应时间等因素的影响。本实验借助激光散射粒度分布分析仪研究Si O2微球在溶液态的分布情况,同时使用SEM对烘烤干燥后的Si O2微球进行表征,该方法制得的纳米Si O2微球分布集中,平均粒径在90 nm左右。     

Effect of BN nanoparticle content in SiC matrix on microstructure and mechanical properties of SiC/SiC composites

BN-nanoparticle-containing SiC-matrix-based composites comprising SiC fibers and lacking a fiber/matrix interface (SiC/BN + SiC composites) were fabricated by spark plasma sintering (SPS) at 1800°C for 10 min under 50 MPa in Ar. The content of added BN nanoparticles was varied from 0 to 50 vol.%. The mechanical properties of the SiC/BN + SiC composites were investigated thoroughly. The SiC/BN + SiC composites with a BN nanoparticle content of 50 vol.%, which had a bulk density of 2.73 g/cm³ and an open porosity of 5.8%, exhibited quasiductile fracture behavior, as indicated by a short nonlinear region and significantly shorter fiber pullouts owing to the relatively high modulus. The composites also exhibited high strength as well as bending, proportional limit stress, and ultimate tensile strength values of 496 ± 13, 251 ± 30, and 301 MPa ± 56 MPa, respectively, under ambient conditions. The SiC fibers with contents of BN nanoparticles above 30 vol.% were not severely damaged during SPS and adhered to the matrix to form a relatively weak fiber/matrix interface.     

Preparation of smooth and dense composite films consisting of MEHPPV and neat C60 by means of electrophoretic deposition

A procedure to prepare flat and dense composite films of a conjugated polymer poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylene vinylene] (MEHPPV) and various amounts of neat C₆₀ by means of electrophoretic deposition from dilute suspensions is reported. It has been observed that deposition from suspensions containing both components results in pinhole-free films, which are applicable to photovoltaic devices, while inhomogeneous films are formed from the suspensions containing only one of the components. The applicability of electrophoretic deposition to obtain polymer-C₆₀ composite films showing photovoltaic effects has been successfully demonstrated.     

International mobility of researchers in robotics,computer vision and electron devices: A quantitative and comparative analysis

We investigated author information in scientific articles by approximately 7,000 researchers for a quantitative analysis of researchers’ international mobility. From top journals, we traced the movements of more than 2,200 researchers in the research domains of robotics, computer vision and electron devices. We categorized countries’ characteristics for the balance between the inflow and the outflow of researchers moving internationally. Flow patterns of international mobility confirm that the United States, China and India exhibit the greatest global flows of researchers, with Singapore and Hong Kong attracting remarkable numbers of researchers from other countries. International mobility focusing on institutions reveals that universities in Singapore receive as many foreign researchers as do research universities in the United States. Furthermore, firms and international collaborative research institutes act as alternative receivers to the universities in the electron devices research domain.