ISO/IEC、美日中氢能技术标准化体系比较与建议

技术标准在技术进步、国际贸易中具有重要作用。全景式梳理、比较氢能技术标准化体系发展与现状,对于促进技术进步、规范国际贸易至关重要。本文综述了ISO/IEC、美国、日本和中国等5个主体氢能技术标准化体系：介绍了上述5个主体的氢能标准化机构,详细梳理了ISO/IEC氢能国际标准与美日中氢能国家标准/行业标准的层级结构比例,并按标准具体内容将其归类到8个技术类别中,分析了各主体在8个技术类别中的分布与特征。文中指出相比于美国和日本,中国氢能技术标准化体系存在行业标准数量较少、氢能产业联盟在行业标准制定中主导性弱和部分技术类别覆盖度低的不足。针对上述不足,文章对中国氢能技术标准体系提出两条发展建议：增加行业标准数量,以发挥其对标准体系补充、完善的作用,为此需赋予中国氢能产业联盟制定行业标准的权限;优化中国氢能技术标准分布,提高氢储运与加注以及氢能应用等技术类别的覆盖度,保障氢能产业从定点示范运营到城市群大规模推广的顺利升级。     

Correlations of Hepatic Hemodynamics,Liver Function,and Fibrosis Markers in Nonalcoholic Fatty Liver Disease: Comparison with Chronic Hepatitis Related to Hepatitis C Virus

The progression of chronic liver disease differs by etiology. The aim of this study was to elucidate the difference in disease progression between chronic hepatitis C (CHC) and nonalcoholic fatty liver disease (NAFLD) by means of fibrosis markers, liver function, and hepatic tissue blood flow (TBF). Xenon computed tomography (Xe-CT) was performed in 139 patients with NAFLD and 152 patients with CHC (including liver cirrhosis (LC)). The cutoff values for fibrosis markers were compared between NAFLD and CHC, and correlations between hepatic TBF and liver function tests were examined at each fibrosis stage. The cutoff values for detection of the advanced fibrosis stage were lower in NAFLD than in CHC. Although portal venous TBF (PVTBF) correlated with liver function tests, PVTBF in initial LC caused by nonalcoholic steatohepatitis (NASH-LC) was significantly lower than that in hepatitis C virus (C-LC) (p = 0.014). Conversely, the liver function tests in NASH-LC were higher than those in C-LC (p < 0.05). It is important to recognize the difference between NAFLD and CHC. We concluded that changes in hepatic blood flow occurred during the earliest stage of hepatic fibrosis in patients with NAFLD; therefore, patients with NAFLD need to be followed carefully.     

Fabrication of Uniaxially Aligned Poly(propylene) Nanofibers via Handspinning

A straightforward method, which is termed novel handspinning, is reported for producing uniaxially aligned sPP nanofibers. As demonstrated by SEM analysis, the morphologies of handspun sPP nanofibers are strongly dependent upon the processing conditions such as spinning method and solvent system. Compared to the normal electrospun sPP nanofibers, the handspun sPP nanofibers show smoother morphologies. FT‐IR analysis demonstrates a significant difference in polymer chain conformation between the handspun and electrospun sPP nanofibers. Moreover, interestingly, the handspun sPP single nanofibers show higher Young's modulus and tensile strength than electrospun sPP single nanofibers.

     

Decomposition kinetics and recycle of binary hydrogen‐tetrahydrofuran clathrate hydrate

Decomposition kinetics and recycle of hydrogen–tetrahydrofuran (H₂–THF) clathrate hydrates were investigated with a pressure decay method at temperatures from 265.1 to 273.2 K, at initial pressures from 3.1 to 8.0 MPa, and at stoichiometric THF hydrate concentrations for particle sizes between 250 and 1000 μm. The decomposition was modeled as a two‐step process consisting of H₂ diffusion in the hydrate phase and desorption from the hydrate cage. The adsorption process occurred at roughly two to three times faster than the desorption process, whereas the diffusion process during formation was slightly higher (ca. 20%) than that during decomposition. Successive formation and decomposition cycles showed that occupancy seemed to decrease only slightly with cycling and that there were no large changes in hydrate structure due to cycling. Results provide evidence that the formation and decomposition of H₂ clathrate hydrates occur reversibly and that H₂ clathrate hydrates can be recycled with pressure. © 2010 American Institute of Chemical Engineers AIChE J, 2011     

Reduction of higher harmonic sequences in terminal voltage of an AC exciting synchronous generator using magnetically anisotropic slot wedges

This paper describes relationships between characteristics of a magnetically anisotropic slot wedge and voltage higher harmonics in an ac exciting synchronous generator terminal due to permeance ripple caused by an open-slot-type rotor. From the relationships obtained, practical guidelines were formulated for machine designs applying the magnetically anisotropic slot wedge. The results are as follows.

• 1 (1) Equivalent permeability of the magnetically anisotropic slot wedge became isotropic wedge permeability for air-gap flux ripple.
• 2 (2) Two ways were identified to reduce voltage-higher harmonics by using the slot wedges.
• 3 (3) The level of leakage flux passing through the anisotropic slot wedge was determined only by its permeability in the width direction.
• 4 (4) Effectiveness of the magnetic anisotropic slot wedges inserted into the stator slots was verified from experimental results using a model machine of the open- slot-type rotor.

     

Thermal and electrical conduction properties of vertically aligned carbon nanotubes produced by water-assisted chemical vapor deposition

We present both thermal and electrical conduction properties of vertically aligned carbon nanotubes (VACNTs), synthesized by the water-assisted chemical vapor deposition method using Fe–Ti–O nanoparticles as catalyst. Thermal diffusivity and electrical resistance of VACNTs have been measured by the laser flash method and direct-current four-terminal method, respectively. The VACNTs are found to have thermal diffusivities of the same order as isotropic graphite and the electrical characteristics of semiconductors. The electrical resistance shows a T^−1/4 temperature dependence, which implies that the conduction of electrons is dominated by 3D Mott variable range hopping.     

Analysis of proton exchange membrane fuel cell catalyst layers for reduction of platinum loading at Nissan

The biggest issue that must be addressed in promoting widespread use of fuel cell vehicles (FCVs) is to reduce the cost of the fuel cell system. Especially, it is of vital importance to reduce platinum (Pt) loading of catalyst layers (CLs) in the membrane electrode assembly (MEA) of a proton exchange membrane fuel cell (PEMFC). In order to lower the Pt loading of the MEA, mass transport of reactants related to the performance in high current density should be enhanced significantly as well as kinetics of the catalyst, which can result in the better Pt utilization and effectiveness. In this study, we summarized our analytical approach and methods for reduction of Pt loading in CLs. Microstructure, mass transport properties of the reactants, and their relation in CLs were elucidated by applying experimental analyses and computational methods. A simple CL model for I–V performance prediction was then established, where experimentally elucidated parameters of the microstructure and the properties in CLs were taken into account. Finally, we revealed the impact of lowering the Pt loading on the transport properties, polarization, and the I–V performance.     

The effects of Ni and Li doping on the performance of lithium manganese oxide material for lithium secondary batteries

Layered Li_0.7[M_1/6Mn_5/6]O₂ (M=Li, Ni) was synthesized using a sol-gel method. P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor was first synthesized by a sol-gel method, and then O2-Li_0.7[M_1/6Mn_5/6]O₂ was prepared by an ion exchange of Li for Na in P2-Na_0.7[M_1/6Mn_5/6]O₂ precursor. From charge/discharge curves, it was seen that Li_0.7[Li_1/6Mn_5/6]O₂ has two plateaus similar to those observed from a spinel structure, but Li_0.7[Ni_1/6Mn_5/6]O₂ holds a single plateau as observed from a typical layered structure. It was considered that Li_0.7[Li_1/6Mn_5/6]O₂ undergoes a phase transformation from layered to spinel structure during the charge/discharge cycle, but Li_0.7[Ni_1/6Mn_5/6]O₂ maintains O2-layered structure after the cycles. Li_0.7[Ni_1/6Mn_5/6]O₂ was higher in discharge capacity and retention rate than Li_0.7[Li_1/6Mn_5/6]O₂.