Sodium Caseinate and Skim Milk Gels Formed by Incubation with Microbial Transglutaminase

Several suspensions and emulsions containing commercial sodium caseinate or skim milk were gelatinized by Ca²⁺-independent microbial transglutaminase treatment. The characteristics of the gels were largely affected by the enzyme concentrations employed. For caseinate gels generally the higher enzyme concentration gave steep decreases in breaking strength, strain and cohesiveness of the gels. The creep tests on emulsified gels prepared to two different enzyme concentrations showed that the gel made with a higher enzyme concentration was the more viscoelastic. For skim milk gels, the enzyme treatment in higher concentration caused substantial increase of the breaking and hardness while the strain and cohesiveness had little or no changes.     

SHAPE CHARACTERIZATION OF TWO-DIMENSIONAL FORMS BY A FRACTION OF ELLIPSE AND DIAMOND

Meloy's method is extended in its use to characterize two dimensional forms by a fraction of ellipse and diamond. The Fourier coefficients are calculated for a vectorial expression of the form about the center of gravity. The value interpolated at the wave number 10 is a good measure for the macroscopic shape, which is assumed to be expressed as a fraction of the values for elippse and diamond. As the microscopic shape index the surface roughness of the form is discussed in terms of the perimeter divided by that of the equivalent ellipse which has the same area as the particle. The shape analysis is applied for various particles of the reference standard dusts.     

High Efficiency Mode Converter for Low-Frequency Gyrotron

A high efficiency quasi-optical (QO) mode converter for high-power, low-frequency gyrotron have been designed and tested. For low-frequency gyrotrons, the scales of the mode converter are comparatively small on the wavelength scale, thus causing significant diffraction losses. Over-1 MW power gyrotron with TE_8,3 cavity at 28 GHz have been developed, which has a high efficiency mode converter designed by the use of numerical methods for launcher optimization. This calculation is sufficiently optimized to maximize the fractional Gaussian content of the far field. The total transmission efficiency from the mode converter to output window is 94.7%. For the experimental result of first tube, the output power of more than 1 MW has been obtained with about 40% efficiency and output burn pattern agrees fairly with the calculated profiles, which imply the design appropriateness. Besides, the frequency dependence for diffraction loss is discussed, and these results give the guiding design principle of the mode converter for high-power, low-frequency and long-pulse gyrotrons.     

Production of Restructured Meat using Microbial Transglutaminase without Salt or Cooking

To produce restructured meat, microbial transglutaminase (MTGase) was evaluated for its ability to introduce covalent crosslinks between protein molecules. Pork muscle cubes were mixed with MTGase and held at 5°C for 2 hr for the enzyme reaction. Restructured products were analyzed for binding strength without cooking. MTGase treatment resulted in effective binding of meat pieces provided there was addition of salt (NaCl). To ensure proper binding without NaCl, some food proteins with MTGase were also investigated. Meat cubes in combination with MTGase and sodium caseinate showed acceptable bind, and sodium caseinate appeared to be a superior substrate for the crosslinking to meat proteins than soy protein, whey protein, or gelatin. These results suggest a useful method for producing restructured meat which can be distributed in the raw, chilled state.     

Selection and Evaluation of Thermal Interface Materials for Reduction of the Thermal Contact Resistance of Thermoelectric Generators

A variety of thermal interface materials (TIMs) were investigated to find a suitable TIM for improving the performance of thermoelectric power generators (TEGs) operating in the medium-temperature range (600–900 K). The thermal resistance at the thermal interface between which the TIM was inserted was evaluated. The TIMs were chosen on the basis of their thermal stability when used with TEGs operating at medium temperatures, their electrical insulating properties, their thermal conductivity, and their thickness. The results suggest that the boron nitride (BN)-based ceramic coating, Whity Paint, and the polyurethane-based sheet, TSU700-H, are suitable TIMs for the heat source and heat sink sides, respectively, of the TEG. Use of these effectively enhances TEG performance because they reduce the thermal contact resistance at the thermal interface.     

Stress Analysis and Output Power Measurement of an n-Mg2Si Thermoelectric Power Generator with an Unconventional Structure

We examine the mechanical stability of an unconventional Mg₂Si thermoelectric generator (TEG) structure. In this structure, the angle θ between the thermoelectric (TE) chips and the heat sink is less than 90°. We examined the tolerance to an external force of various Mg₂Si TEG structures using a finite-element method (FEM) with the ANSYS code. The output power of the TEGs was also measured. First, for the FEM analysis, the mechanical properties of sintered Mg₂Si TE chips, such as the bending strength and Young’s modulus, were measured. Then, two-dimensional (2D) TEG models with various values of θ (90°, 75°, 60°, 45°, 30°, 15°, and 0°) were constructed in ANSYS. The x and y axes were defined as being in the horizontal and vertical directions of the substrate, respectively. In the analysis, the maximum tensile stress in the chip when a constant load was applied to the TEG model in the x direction was determined. Based on the analytical results, an appropriate structure was selected and a module fabricated. For the TEG fabrication, eight TE chips, each with dimensions of 3 mm × 3 mm × 10 mm and consisting of Sb-doped n-Mg₂Si prepared by a plasma-activated sintering process, were assembled such that two chips were connected in parallel, and four pairs of these were connected in series on a footprint of 46 mm × 12 mm. The measured power generation characteristics and temperature distribution with temperature differences between 873 K and 373 K are discussed.     

Effective cell separation utilizing poly(N-isopropylacrylamide)-grafted polypropylene membrane containing adsorbed antibody

We previously developed a cell separation method using a poly(N-isopropylacrylamide)-grafted polypropylene (PNIPAAm-g-PP) membrane containing an adsorbed monoclonal antibody (mAb). The purpose of this study is to elucidate the cell separation mechanism in detail and to design an optimal method. As the grafting yield of PNIPAAm increased, the level of the adsorption of IgG(1) and cell adhesion to the membrane decreased. After BSA was adsorbed to a PNIPAAm-g-PP membrane at 6 degrees C, where PNIPAAm was hydrophilic, a small amount of IgG(1) was adsorbed to the membrane at 37 degrees C, where PNIPAAm was hydrophobic. The desorption of the adsorbed IgG(1) was not enhanced even though temperature was reduced to 10 degrees C, where PNIPAAm was hydrophilic. These results indicate that the antibody adsorbed to the intact PP surface of the membrane predominantly contributes to the capture of target cells through the antigen-antibody reaction and that a thermoresponsive transition of PNIPAAm contributes to the detachment of the captured cells. The total number of cells recovered from a PNIPAAm-g-PP membrane containing the adsorbed mAb decreased as the grafting yield increased. A PNIPAAm-g-PP membrane with a 1.7% grafting yield containing adsorbed anti-human CD34 mAb enriched CD34-positive KG-1a cells to 85% from a 1:1 cell suspension of KG-1a cells and CD34-negative Jurkat cells.     

Gel Strength Enhancement by Addition of Microbial Transglutaminase during Onshore Surimi Manufacture

Surimi from Alaska pollock flesh was manufactured onshore with Microbial transglutaminase (MTGase). Effect of MTGase was investigated by evaluating breaking strength and deformation of gels from MTGase-treated surimi with and without setting at 30°C. Quantitative analysis of ε-(γ-glutamyl)lysine (GL) crosslink was also carried out to monitor the MTGase reaction. In set gels, breaking strength and GL crosslink increased, and myosin heavy chain decreased correspondingly with MTGase concentration. These changes were smaller in gels prepared without setting. Results suggest that surimi gel could be improved through the formation of GL crosslinks by added MTGase in surimi.     

Surge analysis of the tank of a gas-insulated line using lumped constant circuits

Surge voltages evaluated by a digital analysis method, for example, electromagnetic transients program (EMTP) and by an analog analysis method (transient network analyzer: TNA) are compared with experimental results on a scaled model of a gas insulated line. From the results, it is confirmed that the analog analysis method has a satisfactory accuracy and its computing speed is quite high. The error caused by the lumped element modeling of the gas insulated line is comparatively small, and the line is not necessary to be treated as a distributed parameter line. The lumped element model is advantageous to understand the mechanism of the transient characteristic of the induced transient voltage. A simple equivalent circuit of the gas insulated line is proposed and its accuracy is confirmed by a comparison with the calculated result obtained by an accurate line method. The transient overvoltages of the tank and across the insulated flange can be analytically calculated using the equivalent model.