Electrochemical curing of epoxy resins

An electrochemical method has been developed for bonding electrically-conductive adherends. The procedure is based on the electrochemical generation of a curing agent from an otherwise chemically-unreactive precursor mixed with an epoxy resin sandwiched between the bonding members. The one-part epoxy resin is storage stable and cured rapidly on passage of current.     

A torsional transducer through in-plane shearing of paired planar piezoelectric elements

A torsional microtransducer for high-power applications was developed using standard bulk lead zirconium titantate (PZT) placed upon a small rectangular prism made from phosphor bronze, with a tapered conical end serving as a horn and a machined interior to improve the actuator's response. Torsion was obtained from a prototype at the design frequency of 192 kHz as well as over a wide range of frequencies from 136 kHz to 1.02 MHz. Torsional vibration velocities of 335 mm/s at 192 kHz were measured at 27.3 V(RMS) on the 1.5-mm diameter output tip, amounting to 25,600 degree/s vibration velocity along the outer circumference of the tip. At 1.02 MHz, a torsional vibration velocity of 1750 mm/s (134,000 degree/s) at 17.8 V(RMS) was obtained through use of the thickness mode of the PZT elements. Using the design described in this study, high-power torsional transducers with diameters of 5 mm and below are now possible.     

A single-element tuning fork piezoelectric linear actuator

This paper describes the design of a piezoelectric tuning-fork, dual-mode motor. The motor uses a single multilayer piezoelectric element in combination with tuning fork and shearing motion to form an actuator using a single drive signal. Finite-element analysis was used in the design of the motor, and the process is described along with the selection of the device's materials and its performance. Swaging was used to mount the multilayer piezoelectric element within the stator. Prototypes of the 25-mm long bidirectional actuator achieved a maximum linear no-load speed of 16.5 cm/s, a maximum linear force of 1.86 N, and maximum efficiency of 18.9%.     

State difference feedback for stabilizing uncertain steady states of non-linear systems

Supposing a non-linear system is subjected to parametric uncertainties, the present paper aims at stabilizing its unstable steady states. A distinctive feature of the problem is that exact information about the steady state is unavailable. To cope with the difficulty, we have examined the applicability of the state difference feedback which uses the difference between the present state x(t) and the past state x(t-T). A rigorous stability analysis has been executed for the case where state deviations are controllable by a single input variable. The stability analysis has led to a favourable conclusion that if the number of unstable modes is just two, and if they are not associated with the origin in the complex plane, we are always able to find a controller which stabilizes the deviations from the unknown steady state. Design process is illustrated by using two kinds of pendulum systems.     

Spin Injection Processes in ZnSe-Based Double Quantum Dots of Diluted Magnetic Semiconductors

Spin injection processes in the double quantum dots of ZnSe-based diluted magnetic semiconductors are discussed. Double quantum dots are fabricated from ZnSe-based double quantum wells by electron beam lithography and wet etching. In these samples, the photo-excited carriers in the magnetic dots are injected into the non-magnetic dots. The circular polarization degrees of photoluminescence from the non-magnetic dots are measured by micro-photoluminescence measurement system under the magnetic field up to 5 T. The maximum spin polarization degrees of injected carriers determined from our experiment are 10% for double quantum wells and 15% for double quantum dots. The spin injection efficiency was estimated both from the observed circular polarization degree and the diffusion length of carriers. We concluded that the spin injection efficiency is increased in the double quantum dots.     

Rapid erasing of wettability patterns based on TiO2-PDMS composite films

TiO₂-polydimethylsiloxane (TiO₂-PDMS) composite films are prepared using the sol–gel method from a Ti(OBu)₄–benzoylacetone solution containing PDMS. The prepared films are cured by irradiation with ultraviolet (UV) light. Structural changes in the films after UV irradiation are confirmed by UV–vis absorption experiments, which show that an absorption band characteristic of the benzoylacetonate chelate rings disappears. This finding is ascribed to structural changes associated with the dissociation of the chelate rings. The IR spectra of the thin films exhibit a broad absorption band after UV irradiation, indicating that a Ti–O–Ti network forms in the thin film. Contact angles are measured for the TiO₂-PDMS thin films, showing wettability conversion from hydrophobic to superhydrophilic states by irradiation with oxygen plasma for 1 s. This phenomenon is explained by XPS experiments which reveal that the number of carbon atoms decreases, whereas the number of oxygen atoms increases on the surface of the TiO₂-PDMS composite films. Finally, hydrophobic–superhydrophilic patterns are fabricated based on a patterned TiO₂-PDMS composite film. The film displays a rapid change to superhydrophilicity over the whole film surface upon plasma irradiation for 1 s, which means that the wettability patterns are rapidly erasable.     

Development of the Water Cooled Ceramic Breeder Test Blanket Module in Japan

The development of a Water Cooled Ceramic Breeder (WCCB) Test Blanket Module (TBM) is being performed as one of the most important steps toward DEMO blanket in Japan. For the TBM testing and evaluation toward DEMO blanket, the module fabrication technology development by a candidate structural material, reduced activation martensitic/ferritic steel, F82H, is one of the most critical items from the viewpoint of realization of TBM testing in ITER. In Japan, fabrication of a real scale first wall, side walls, a breeder pebble bed box and assembling of the first wall and side walls have succeeded. Recently, the real scale partial mockup of the back wall was fabricated. The fabrication procedure of the back wall, whose thickness is up to 90 mm, was confirmed toward the fabrication of the real scale back wall by F82H. Important key technologies are almost clarified for the fabrication of the real scale TBM module mockup. From the view point of testing and evaluation, development of the technology of the blanket tritium recovery, development of advanced breeder and multiplier pebbles and the development of the blanket neutronics measurement technology are also performed. Also, tritium production and recovery test using D-T neutron in the Fusion Neutronics Source (FNS) facility has been started as the verification test of tritium production performance. This paper overviews the recent achievements of the development of the WCCB TBM in Japan.     

InGaAs-InGaAsP buried heterostructure lasers operating at 2.0 μm

Buried heterostructure lasers with highly strained InGaAs-InGaAsP active regions, emitting at 2 μm have been fabricated and tested. The lasers exhibited threshold current densities of 500 A/cm² for 1-mm-long cavities, an internal loss of 11 cm^-1, and characteristic temperatures as high as 50°C. The gain characteristics were also investigated and a linewidth enhancement factor of 8 was determined     

Detection of serum p53 antibodies in patients with esophageal squamous cell carcinoma: correlation with clinicopathologic features and tumor markers

The significance of serum p53-Abs in patients with esophageal squamous cell carcinoma was determined. Examination of clinicopathological features and assessment of tumor marker sensitivities of carcinoembryonic antigen (CEA), squamous cell carcinoma antigen (SCC-Ag) and CYFRA21-1 were performed. Thirty-three (58%) of 57 patients were positive for serum p53-Abs, however, no relation with cancer progression existed. Fourteen of the 33 sero-positive patients revealed normal levels of all tumor markers tested. Thus, serum p53-Abs appears to be a useful marker for the detection of esophageal squamous cell carcinoma.