Colorimetric microdetermination of sulphites in foods by use of the modified rankine apparatus. IV.

Summary Detection and determination of traces of sulphites in foods was attempted by use of the modified Rankine apparatus and pararosaniline colorimetry. Replacement of alkaline titration reported previously by pararosaniline colorimetry lowered the absolute detection limit from 30 g (titration method) to 2 g. In view of clean analysis, in the color developing system, 0.1 N-sodium hydroxide was used in place of mercuric chloride solution commonly used as an absorbant of sulphites. In order to prevent oxidative decomposition of sulphites during operation, nitrogen gas was used as carrier instead of air. Dimedone and sodium azide were used for the elimination of aldehydes and nitrites, respecitvely, in the sample, which will disturb the color development of sulphites with pararosaniline-formaldehyde reagents. With this improved method, it was possible to determine the residual sulphites in frozen peeled shrimps, sugared beans and other foods with low sulphite contents accurately.

---

Colorimetrische Mikrobestimmung von Sulfiten in Lebensmitteln bei Anwendung der modifizierten IV. Rankine Apparatur

Zusammenfassung Geringe Sulfitmengen in Lebensmitteln (geschälte Garnelen, gezuckerte Bohnen) können colorimetrisch bestimmt werden. Die neuentwickelte Methode beruht auf einer Kombination von colorimetrischer Bestimmung mittels p-Rosanilin und der Bestimmungsmethode nach Rankine. Auf diese Weise lassen sich Gehalte von 2 g noch genau bestimmen. Bei der Farbentwicklung wurde das giftige Quecksilbertetrachlorid durch 0.1 n-NaOH ersetzt, anstelle von Luft Stickstoff als Trägergas verwendet und somit eine Oxydation des Sulfits während der Bestimmung vermieden. Da Nitrit und Aldehyde die Farbentwicklung stören, wurde ihr Einfluß durch Dimedon und Natriumazid ausgeschaltet.

---

---

Studies on the Analyses of Sulphites in Foods (IV)     

Crystal orientation changes of Ag thin films on the Si(111) substrate due to tribo-assisted recrystallization

Crystal orientation changes of Ag thin films due to the tribo-assisted recrystallization have been studied using grazing incidence X-ray diffraction with synchrotron radiation. After preparation of an Si(111) √3 × √3-Ag surface, a 5-nm-thick Ag film was deposited on the surface at the substrate temperature of 303 K in an ultra-high vacuum chamber. The friction experiments were carried out using a diamond pin-on-plate type tribometer just after the Ag deposition in the same UHV chamber. We found that the coefficient of friction of the Ag films on the Si(111) √3 × √3-Ag surface decreases from 0.07 to 0.03, with increasing reciprocal sliding cycles. In synchronization with the coefficient change, Ag{100} grains are gradually disappearing. As a result, the Ag{111} grains cover the entire surface after 50 sliding cycles. Moreover, we found that the domain size of the Ag{111} grains increases with increasing reciprocal sliding cycles by measuring the rocking curve width. These results directly show that the Ag(111) plane is the sliding plane of friction and the coefficient of friction of Ag films is determined by the fraction of the Ag(111) grains in the Ag films. Moreover, to clarify the reaction between the Ag film and the Si substrate due to the tribo-assisted recrystallization, the substrate strain has been studied by an extremely asymmetric X-ray diffraction technique using synchrotron radiation.     

Leak-tightness characteristics concerning the containment structures of the HTTR

The containment structures of the HTTR consist of the reactor containment vessel, the service area, and the emergency air purification system, which minimise the release of fission products in postulated accidents, which lead to fission product release from the reactor facilities. The reactor containment vessel is designed to withstand the temperature and pressure transients and to be leak-tight in the case of a rupture of the primary concentric hot-gas duct, etc. The pressure inside the service area is maintained at a negative pressure by the emergency air purification system. The emergency air purification system will also remove airborne radioactivity and will maintain a correct pressure in the service area.The leak-tightness characteristics of the containment structures are described in this paper. The measured leakage rates of the reactor containment vessel were enough less than the specified leakage limit of 0.1%/d confirmed during the commissioning tests and annual inspections. The service area was kept in a way that the design pressure becomes well below its allowable limitation by the emergency air purification system, which filters efficiency of particle removal and iodine removal well over the limited values.The obtained data demonstrate that the reactor containment structures were fabricated to minimise the release of fission products in the postulated accidents with fission product release from the reactor facilities.     

Observation of very thin gold island films vacuum-deposited onto MoS2 surface by STM

A gold film of about half a monolayer in thickness was vacuum-deposited onto air-cleaved MoS₂ surface at room temperature at a pressure of 10^?5 Pa. Quasi-two-dimensionally grown gold islands made of several atomic layers were observed by scanning an area of 40×30 nm². The shape of them was oblate and about 20 nm in diameter. Atomic corrugations which reflect the Au(111) surface were observed. The islands were found to move and changed their shape during the microscopy.     

Martensitic stabilization and defects induced by deformation in TiNi shape memory alloys

Martensitic stabilization caused by deformation in a TiNi shape memory alloy was studied.Special attention was paid to the deformed microstructures to identify the cause of martensitic stabilization.Martensitic stabilization was demonstrated by differential scanning calorimetry for the tensioned TiNi shape memory alloy.Transmission electron microscopy revealed that antiphase boundaries were formed because of the fourfold dissociation of[110]B19'super lattice dislocations and were preserved after reverse transformation due to the lattice correspondence.Martensitic stabilization was attributed to dislocations induced by deformation,which reduced the ordering degree of the microstructure,spoiled the reverse path from martensite to parent phase compared with thermoelastic transformation,and imposed resistance on phase transformation through the stress field.     

Investigations on welding residual stresses in penetration nozzles by means of 3D thermal elastic plastic FEM and experiment

Recent discoveries of stress corrosion cracking (SCC) in weldments including penetration nozzles at pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It is well known that welding residual stress is an important factor resulting in SCC in weldments. In the present work, both experimental method and numerical simulation technology are used to investigate the characteristics of welding residual stress distribution in penetration nozzles welded by multi-pass J-groove joint. An experimental mock-up is fabricated to measure welding residual stress at first. In the experiment, each weld pass is performed using a semi-circle balanced welding procedure. Then, a corresponding finite element models with considering moving heat source, deposition sequence, inter-pass temperature, temperature-dependent thermal and mechanical properties, strain hardening and annealing effect is developed to simulate welding temperature and residual stress fields. The simulation results predicted by the 3D model are generally in good agreement with the measurements. Meanwhile, to clarify the influence of deposition sequence on the welding residual stress, the welding residual stress field in the same geometrical model induced by a continuous welding procedure is also calculated. Finally, the influence of a joint oblique angle on welding residual stress is investigated numerically. The numerical results suggest that both deposition sequence and oblique angles have effect on welding residual stress distribution.     

Development of correlation-based clustering method and its application to software sensing

The individuality of production devices should be taken into account when soft-sensors are designed for parallelized devices. Since it is expressed as differences of the correlation among measured variables, it is useful to cluster samples on the basis of the correlation among variables for adopting a multi-model approach. In addition, changes in process characteristics can be coped with in the same way. In the present work, a new clustering method, referred to as NC-spectral clustering, is proposed by integrating the nearest correlation (NC) method and spectral clustering. Spectral clustering is a graph partitioning method that can be used for sample classification when an affinity matrix of a weighted graph is given. The NC method can detect samples that are similar to the query from the viewpoint of the correlation without a teacher signal. In the proposed method, the NC method is used for constructing the weighted graph that expresses the correlation-based similarities between samples and the constructed graph is partitioned by using spectral clustering. In addition, a new soft-sensor design method is proposed on the basis of the proposed NC-spectral clustering. The usefulness of the proposed methods is demonstrated through a numerical example and a case study of parallelized batch processes. The performance of the proposed correlation-based method is better than that of the conventional distance-based methods.     

Psychological Stress Exacerbates Inflammation of the Ileum via the Corticotropin-Releasing Hormone-Mast Cell Axis in a Mouse Model of Eosinophilic Enteritis

The effects of psychological stress on eosinophilic gastrointestinal disorders have not been elucidated. This study investigated the effects of psychological stress in a mouse model of eosinophilic enteritis (EoN). BALB/c mice were treated with ovalbumin (OVA) to create an EoN model and subjected to either water avoidance stress (WAS) or sham stress (SS). Microscopic inflammation, eosinophil and mast cell counts, mRNA expression, and protein levels of type 2 helper T cell (Th2) cytokines in the ileum were compared between groups. We evaluated ex vivo intestinal permeability using an Ussing chamber. A corticotropin-releasing hormone type 1 receptor (CRH-R1) antagonist was administered before WAS, and its effects were analyzed. WAS significantly increased diarrhea occurrence and, eosinophil and mast cell counts, and decreased the villus/crypt ratio compared to those in the SS group. The mRNA expression of CRH, interleukin IL-4, IL-5, IL-13, eotaxin-1, and mast cell tryptase β2 significantly increased, and the protein levels of IL-5, IL-13, and OVA-specific immunoglobulin E (IgE) also significantly increased in the WAS group. Moreover, WAS significantly increased the intestinal permeability. The CRH-R1 antagonist significantly inhibited all changes induced by WAS. Psychological stress exacerbated ileal inflammation via the CRH-mast cell axis in an EoN mouse model.     

Thermoreversible behavior of κ-carrageenan and its apatite-forming ability in simulated body fluid

Osteoconductive materials with self-setting ability have received much attention because their properties allow developing injectable materials for bone defects. Thermosensitive hydrogel with ability of bone-like apatite formation in a body environment is a candidate of injectable bone fillers with osteoconductivity because the apatite formation on materials is an essential to show osteoconduction. The present study focused on the development of a thermosensitive hydrogel through modifications of the sulphonic groups of the polysaccharide, κ-carrageenan, with potassium chloride (KCl) and calcium chloride (CaCl₂). We found that the gelation temperature of κ-carrageenan solutions increased with increasing amounts of K⁺ ions. Apatite formation was observed on the gel after exposure to simulated body fluid for 0.5 day when the gel was prepared with a molar ratio of Ca²⁺/sulfonic groups = 1.5. These results indicate that a thermosensitive κ-carrageenan hydrogel with apatite-forming ability was obtained through the incorporation of K⁺ and Ca²⁺ ions into the solution.