Strengthening of Preloaded RC Beams Using Hybrid Carbon Sheets

Reinforced concrete (RC) beams subject to service loads of 40 or 60% of steel yielding were strengthened using hybrid continuous carbon fiber sheets. The hybrid systems were made of high-strength and high-modulus carbon sheets, and compared with systems using only high-strength carbon. It was found that the use of high-modulus carbon sheets in hybrid systems could increase the yielding load, the flexural stiffness, the postyielding ductility, and reduce the crack opening in concrete. The slope changes on load-deflection curves at steel yielding are not noticeable in hybrid systems. The tensile strains developed in hybrid sheets after the fracture of high-modulus carbon are higher in magnitude and distributed in a larger area, leading to an ultimate carbon fracture with concrete crushing. These unique features are attributed to the high stiffness and low ultimate tensile strain of the high-modulus carbon fibers which stiffen the structures, avoid or delay the fiber-reinforced polymer debonding, and facilitate the deformability during their subsequent breakdown.     

Identification of stress-induced leakage current components and thecorresponding trap models in SiO2 films [MOStransistors]

Time-decay stress-induced leakage current (SILC) has been systematically investigated for the cases of both Fowler-Nordheim (FN) stress and substrate hot-hole stress. From the three viewpoints of the reproducibility of the current component for the gate voltage scan, the change of oxide charge during the gate voltage scan, and the resistance of the current component to thermal annealing, it has been found that time-decay stress-induced leakage current is composed of five current components, regardless of stress type. Trap models corresponding to each current component have been proposed. In addition, it has also been proven that holes generate the electron traps related to one of those current components     

High-dose intravenous steroid pulse therapy in thyroid-associated ophthalmopathy

MIcrospheres containing diclofenac sodium (DS) were prepared using carboxymethylcellulose (CMC) as the main support material (1.0, 2.0, 3.0% (w/v)) and aluminum chloride as the crosslinker. Drug to polymer ratios of 1:1, 1:2 and 1:4 were used to obtain a range of microspheres. The microspheres were then coated with an enteric coating material, Eudragit S-100, efficiency, % yield value, particle sizes an in-vitro dissolution behaviour were investigated. The surface of the enteric coated microspheres seemed to be all covered with Eudragit S-100 from scanning electron microscopy observation. It was also observed that increasing the CMC concentration led to an increase in the encapsulation efficiency, % yield value and particle size and decreased the release rate. Eudragit S-100 coating did not significantly alter the size but the release rate was significantly lower even when the lower concentration solution was used.     

Effectiveness of spatial representation in the formation of network communities: experimental study on community organizer

In this paper, we present and discuss Community Organizer, a system designed to support network communities. The main characteristic of Community Organizer is the use of spatial representations for the relationships among community members including the communications exchanged among these members. These spatial representations reflect the degree of closeness of interests and concerns among the members, and are intended to provide users with clues on how to form network communities. In order to investigate the effectiveness of the proposed spatial representations, we conducted experiments with two different versions of the software. One version offered meaningful spatial representations while the other version did not. The subjects who used the former software version felt a greater sense of ‘community’, enjoyed using the software more, and actively used it longer than the subjects using the latter software version (control condition). These results indicated that the proposed spatial representations are effective in supporting network community formation.     

Hot carrier magnetophonon spectroscopy of semiconductors in high magnetic fields up to 40 T

Hot carrier magnetophonon resonances of n-type Si, short channel InP and p-type InSb were investigated in pulsed high magnetic fields up to 40 T. Using a recently developed high resolution technique in pulsed high fields, many new features of the hot carrier-phonon interactions in high magnetic fields were found.     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Light scattering studies on crystallization in polyethylene terephthalate

The light scattering from the spherulites of polyethylene terephthalate grown near the glass transition temperature has been investigated. The Hv scattering profiles can be reproduced by the sum of the ideal spherulite scattering with the distribution of spherulite radius and the isotropic scattering from randomly oriented crystallites. The ratio of optical anisotropies in the isotropic scattering to the ideal spherulite scattering is obtained by the method established to eliminate the effects of the number density of spherulites and the coefficient depending on the experimental conditions. It is found that the anisotropy ratio is almost independent of the crystallization time and of temperature above 106 °C, while it is larger at a crystallization temperature of 103 °C. The spherulitic structure is discussed in terms of the anisotropy ratio.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

Development of a fast neutron radiography converter using wavelength-shifting fibers

A fluorescent converter for fast neutron radiography (FNR) comprising a scintillator and hydrogen-rich resin has been developed and applied to electronic imaging. The rate of the reaction between fast neutrons and the converter is increased by thickening the converter, but its opaqueness attenuates emitted light photons before they reach its surface. To improve the luminosity of a fluorescent converter for FNR, a novel type of converter was designed in which wavelength-shifting fibers were adopted to transport radiated light to the observation end face. The performance of the converter was compared with that of a polypropylene-based fluorescent converter in an experiment conducted at the fast-neutron-source reactor YAYOI in the University of Tokyo.