Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Bio-layer management in anaerobic membrane bioreactors for wastewater treatment.

Membrane separation technology represents an alternative way to achieve biomass retention in anaerobic bioreactors for wastewater treatment. Due to high biomass concentrations of anaerobic reactors, cake formation is likely to represent a major cause of flux decline. In the presented research, experiments are performed on the effect of biomass concentration and level of gas sparging on the hydraulic capacity of a submerged anaerobic membrane bioreactor. Both parameters significantly affected the hydraulic capacity, with biomass exerting the most pronounced effect. After 50 days of continuous operation the critical flux remained virtually unchanged, despite an increase in membrane resistance, suggesting that biomass characteristics and hydraulic conditions determine the bio-layer formation rather than the membrane's fouling level. The concept of bio-layer management is introduced to describe the programmed combination of actions performed in order to control the formation of biomass layer over membranes.     

Use of citric acid for heavy metals extraction from contaminated sewage sludge for land application.

Recent studies revealed that organic acids such as citric and oxalic acids seemed to be more promising as chemical extracting agents for removal of heavy metals from contaminated sludge, since they are biodegradable and can attain a higher metal extraction efficiency at mildly acidic pH compared to other extracting agents. Results of a lab-scale study on the efficiency of citric acid in the extraction of chromium (Cr), copper (Cu), lead (Pb), nickel (Ni) and zinc (Zn) from anaerobically digested sludge, revealed that citric acid seemed to be highly effective in extracting Cr (at 100%), Cu (at 88%), Ni (at 98%) and Zn (at 100%) at pH 2.33, mostly at 5 days leaching time except for Cu and Zn, which are at 1 day and 2 h contact times respectively. Lead removal at the same pH was also high at 95% but at a longer leaching time of 11 days. At pH 3, citric acid seemed to be highly effective in extracting Pb (at 100%) at 1 day leaching time, although higher removals were also attained for Ni (70%) and Zn (80%) at only 2 h leaching time. Chemical speciation studies showed that Cr, Cu and Ni in the sludge sample seem to predominate in residual fractions, while Pb and Zn were found mostly bound to organic and inorganic matter forms, hence the potential of the sludge for land application.     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Pseudorandom active UWB reflectors for accurate ranging

In this letter, the concept of pseudorandom active reflector, based on the ultra-wideband (UWB) technology, is introduced. It consists of a simple device that repeats a slightly delayed version of the received UWB signal only in certain time intervals according to a suitable pseudorandom time-hopping sequence. An example of application of this device for accurate ranging in precise location systems is given. The advantages of this solution are in the hardware simplicity (only the analog section is present), in the low power consumption of the reflector and in the low timing constraint regarding the relative transmitter and reflector clock rates.     

Steady-state operation of a high-voltage multiresonant converter in a high-temperature environment

Often scientific instruments on exploratory satellites are used to collect cosmic particles. These instruments, such as the Faraday cup, require a high-voltage regulated power source. On the proposed solar probe satellite there will be instruments which will collect cosmic particles close to the sun. Naturally temperature effects on the voltage regulator are a concern. Specifically power dissipation within the regulator must stay within stringent guidelines. The high-voltage regulator circuit is a resonant flyback topology with a dissipative series switch whose on resistance controls the output voltage level. The extreme temperatures in space will change the inductance of the flyback transformer which will affect the output voltage. State space analysis techniques are used to determine how the value of the transformer inductance and capacitance in the flyback converter affects the output voltage and consequently the power dissipated by the transformer and the switch. The accuracy of the analysis is verified by comparing results with those obtained from an experimental circuit. The results can then be used to help the designer chose nominal capacitance and inductance values that will work over the temperature range of interest.     

Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Piezoelectrically actuated four-bar mechanism with two flexible links for micromechanical flying insect thorax

In this paper, a piezoelectrically actuated four-bar mechanism with two flexible links is proposed to be used in a micromechanical flying insect robot wing thorax for stroke amplification. PZT-5H- and PZN-PT-based unimorph actuators are utilized at the input link of the four-bar for a compact and lightweight thorax transmission mechanism. The kinematics and dynamics of the proposed wing structure with two parallel four-bar mechanisms are analyzed, optimal four-bar link size selection method is introduced, and quasistatic forces generated at the wing are computed for evaluating the feasibility of the design. Using laser micromachining and folding techniques, prototype four-bar structures are constructed. In the experiments, for a 10/spl times/1/spl times/0.12 mm/sup 3/ PZT-5H actuator-based four-bar mechanism, the stroke amplification of around 20 - 25 is held, and an attached polyester wing is resonated at 29 Hz with around 90/spl deg/ flapping motion. These results match closely with the predicted theoretical values.