Uniform carbon‐nanotube emitter for field‐emission displays

Abstract— The synthesis of carbon‐nanotube (CNT) field emitters for FEDs by thermal chemical vapor deposition (CVD) and their structural and emission characterization are described. Multi‐walled nanotubes (MWNTs) were grown on patterned metal‐base electrodes by thermal CVD, and the grown CNTs formed a network structured layer covering the surfaces of the metal electrode uniformly, which realized uniform distribution of electron emission. A technique for growing narrow MWNTs was also developed in order to reduce the driving voltage. The diameter of MWNT depends on the growth temperature, and it has changed from 40 nm at the low temperature (675°C) to 10–15 nm at the high temperature (900–1000°C). Moreover, narrower MWNTs were grown by using the metal‐base electrode covered with a thin alumina layer and a metal catalyst layer. Double‐walled nanotubes (DWNTs) were also observed among narrow MWNTs. The emission from the narrow CNTs showed a low turn‐on electric field of 1.5 V/μm at the as‐grown layer.     

The effect of the membrane fluidity on pharmacokinetics for lipid A analog E5531

The effect of the dispersing procedure on the aggregate size, membrane fluidity and the pharmacokinetics were evaluated for the lipid A analog E5531. The size of the aggregates prepared by the pH-jump method (pH 11.0 → 7.3) was decreased, reaching 20 nm with increasing dispersing time in 0.003 N NaOH (pH 11.0). The membrane fluidity of the aggregates increased with increasing dispersing time. When prepared by the normal dilution method (pH 7.3 → 7.3), the size of the aggregates remained constant at 150 nm and the membrane fluidity was smaller compared to samples prepared by the pH-jump method. Using samples with different degrees of hydration and different membrane fluidities prepared by the pH-jump method, the pharmacokinetics after intravenous administration into rats were evaluated, and the data obtained confirmed that the membrane fluidity was correlated with the pharmacokinetics in rat. In addition, E5531 vials were stable for 24 months at room temperature when used within 24 hr after reconstitution.     

The effects of a detuned optical input on bistable laser diodeswith inhomogeneous current injection

The effects of an external optical input on a bistable laser diode (BLD) with inhomogeneous current injection are discussed. The bistable behavior of optical output versus injection current is shown to be variously modified, depending on the wavelength and power of the optical input. Optical set and reset operations and optical logic achieved by optical input pulses can be explained by these characteristics of a BLD modified by an external optical signal. Analysis using rate equations is also offered to help interpretation of experimental results, as well as the optical output and the bias current injected into the BLD     

Fatigue behavior of carburized steel with internal oxides and nonmartensitic microstructure near the surface

The characteristic fatigue behavior of carburized and quenched steel with internal oxides and non-martensitic microstructure near the surface was presented through rotating bending fatigue test. The S-N diagram revealed two knees and the specimens continued to fail over 10⁷ stress cycles. The fatigue limit could not be obtained even at 10⁸ stress cycles. The test results were compared to those for the specimens without surface structure anomalies to show the effect of structure anomalies on the fatigue behavior of carburized steel.     

Slow crystallization process from amorphous PbTiO3

The effect of isothermal annealing of amorphous PbTiO₃ at a temperature below the crystallization temperature, T_crys, has been investigated. Time dependent dielectric constant in the annealing process has been observed. From the experimental results, both the existence of the glass transition temperature, T_g, and the steadiness of dielectric constant at room temperature have been established.     

Mechanical properties of molybdenum neutron-irradiated at a high temperature

Molybdenum specimens prepared by two processes, powder-metallurgy (PM) and electron-beam melting (EB), were irradiated to a fast neutron fluence of 2.74 × 10²⁴n/m² (E_n? 1 MeV) at about 600°C (873 K), and their mechanical properties were studied in detail. It was shown that the degree of irradiation embrittlement in EB-Mo was smaller than that in PM-Mo, which might be caused by stronger grain-boundaries and probably smaller irradiation-hardening in the former. From the relation between the recovery of ductility and microstructural changes in post-irradiation annealed PM-Mo at 800 (1073 K), 1000 (1273 K) and 1200°C (1473 K), it was concluded that the recovery resulted from a decrease of irradiation hardening due to a rearrangement and a disappearance of depleted-zones, dislocation-loops and voids in order with increasing annealing temperature. An anomalous mode of fracture was observed in as-irradiated specimens, which consisted of inhomogeneous deformation, then brittle fracture not at the center but at the root of the deformation neck. This mode was observed in a narrow temperature range near the DBTT. A possible mechanism is discussed.