Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Influence of Cu<Superscript>2+</Superscript> ions on structural and magnetic properties of NiZn ferrites

The paper is devoted to the preparation of NiZn ferrite with small substitutions of copper by means of ceramic technology. The influence of small Cu substitution on the microstructural and magnetic properties of NiZn ferrites have been analysed by means of various experimental methods and interpreted from the point of view of preparation technology optimisation and possible applications of such materials. A strong correlation between the substituent content and resulting properties has been observed, thus allowing preparation of material with the properties tailored for any particular application.     

Low temperature and strain rate dependence of fracture stress and fracture toughness on thin Fe40Ni40B20 amorphous ribbon

The fracture stress and the critical stress intensity factor of the Fe₄₀Ni₄₀B₂₀ amorphous metallic ribbons 20 μm thick were measured in the temperature range 4.2–300 K and at deformation rates from 3.3×10⁻⁶ to 1.25×10⁻³ m⁻¹ with the aim to obtain more information on the condition for the onset and development of the inhomogeneous plastic deformation and fracture.     

Sparking at cathode tools during electrochemical machining in flow-through cells

The current density used in electrochemical machining can be increased only up to a certain value, above which the formation of electric sparks on the cathode (tool) is observed, whereby the latter is damaged and the anode surface becomes rough. The present work is devoted to the measurement of this critical density for small metal cathodes placed on the wall of a flow-through channel for Reynolds numbers from 1265 up to 5902 and static pressures ranging from 0.1 up to 1.0 MPa. The results are correlated by criterion equations which gave values of critical (sparking) cathodic current density,j _s, with an average error of 7.1 % for laminar flow and 4.1 % for turbulent flow. The equations can be used for the calculation of the sparking current density for industrial flow-through cells for electrochemical machining.     

The influence of preparation conditions on the electrochemical behaviour of CuO in a Li/CuO cell

A dozen CuO samples prepared under various conditions and from different starting materials were evaluated as cathode materials for a primary Li/CuO cell. The “thin electrode” method was used for rapid evaluation of the samples. Both coulombic efficiency and discharge voltage depend considerably on the method of synthesis. No correlation was found between the specific surface area and the resistivity of the samples on the one hand and the cathode performance on the other. Best results were obtained from CuO prepared by the oxidation of Cu₂O under controlled temperature and time of oxidation.     

Kinetic Monte-Carlo simulation of network formation

Summary the simulation described in Part I was applied to random step polyaddition of a trifunctional monomer and the results were compared with exact solution for an infinite system. The gel point conversions, the weight-average degree of polymerization before (P _w) and beyond (P _w,sol) the gel point, the sol fraction and the cycle rank were used for comparison. The best way for detection of the gel point conversion is the extrapolation of the gel fraction, w _g, to w _g=0. The largest fluctuations are exhibited by P _w and P _w,sol. To get results closer to the exact ones, one can repeat several experiments with smaller number of units or increase the number of units, the former way being somewhat more economical. Typical orders of magnitude used were 10⁷ monomeric units.     

Operational experience and recent developments at the National Medical Cyclotron, Sydney

The National Medical Cyclotron, Sydney, Australia commenced operation in mid 1991, with a mission to provide PET and SPECT radionuclides throughout Australia. The realization of the present production capacity has been synonymous with the development of the facility's industrial cyclotron (IBA Cyclone 30). The choice of cyclotron was based on the Cyclone 30's virtues as a compact, user-friendly, energy efficient cyclotron, offering the beam quality characteristic of negative ion technology. Development of the cyclotron has improved reliability and increased beam capacity, while improvements to targetry have increased production reliability. More recently, the installation and commissioning of a new solid target irradiation facility has provided much needed redundancy. This paper describes the major cyclotron and targetry developments carried out to date.     

Application of substituted N-arylpyrroles in the corrosion protection of aluminium in hydrochloric acid

The inhibiting action of N-arylpyrroles on aluminium in 0.17 mol dm^–3 hydrochloric acid solution, in the temperature range 20–60 °C, was studied using potentiodynamic and electrochemical impedence spectroscopy techniques. The inhibiting efficiency of both investigated compounds 1-(2-fluorophenyl)-2,5-dimethylpyrrole (compound A) and 1-(2-fluorophenyl)-2,5-dimethylpyrrole-3-carbaldehyde (compound B) slightly increases with increasing temperature of the corrosive solution. Inhibitor adsorption on the elecrode surface decreases the apparent activation energy of the hydrogen evolution reaction. Compound A follows the Temkin adsorption isotherm, while its carbaldehyde derivative follows the Langmuir isotherm. The results of the apparent energy of activation and the standard free energy of adsorption point to stronger chemisorption of the compound A. However, due to additional condensation of molecules with carbaldehyde groups on the electrode surface, the carbaldehyde derivative exhibits even better inhibiting efficiency than compound A. The kinetic corrosion parameters, analysed in terms of the impedance data, show a satisfactory agreement with those obtained by the potentiodynamic method.