Corrosion resistance of a bent plate from a high-nitrogen nonmagnetic 05Kh22AG15N8M2F steel in aggressive media

The corrosion resistance of the convex and concave sides of bent plates from a high-nitrogen non-magnetic steel has been studied in aqueous solutions of sulfuric and hydrochloric acids. Weighing and hydrogen methods are used to control the corrosion rate of bent-sample sides and to find a number of effects that complement the picture of the stress corrosion of iron alloys and support the existence of the mechanochemical deformation sign effect.     

Simulation of contact stresses and forces during hot rolling of thin wide strips with allowance for a stick zone and elastic regions in the deformation zone

A new procedure for the calculation of contact stresses and hot-rolling forces for wide strips 0.8–1.5 mm thick has been developed and tested. This procedure takes into account the presence of a stick zone in the deformation zone and stress distributions in both elastic and plastic regions in the deformation zone. The average error in the force calculation according to the new procedure is 5%, which is more than two times smaller than the calculation error of well-known force calculation procedures. The developed procedure is used to simulate the contact stresses in the deformation zones of working stands in a six-stand 1700 mill during rolling of strips thinner than 1.0 mm. A number of new relations for the state of stress in a strip have been revealed upon simulation. Some of these relations are as follows: in the last stands, the length of elastic regions accounts for 10–17% of the total deformation-zone length; the maximum normal contact stresses are 1300–1400 MPa, which corresponds to the stresses in the deformation zones of cold-rolling mills; the stick-zone length accounts for 85–99% of the deformation-zone length; and the contact stresses in the stick zone are virtually independent of the friction coefficient. The developed calculation procedure can be used to optimize the technological regimes of wide-strip mills.     

Analytical solution of a system of nonlinear measuring equations of a 12-pole microwave reflectometer

Analytical solution of a system of nonlinear measuring equations of a 12-pole microwave reflectometer was obtained. Criteria for selecting a true solution in the general case were developed and the analysis was conducted for a number of particular cases that may generate practical interest.     

Measurement and modeling of the sidewall threshold voltage ofmesa-isolated SOI MOSFETs

Five-terminal silicon-on-insulator (SOI) MOSFETs have been characterized to determine the threshold voltage at the front, back, and sidewall as a function of the body bias. The threshold voltage shift with the body bias at the front and back interfaces can be explained by the standard bulk body effect equation. However, the threshold voltage shift at the sidewall is smaller than predicted by this equation and saturates at large body biases. This anomalous behavior is explained by two-dimensional charge sharing between the sidewall and the front and back interfaces. An analytical model that accounts for this charge sharing by a simple trapezoidal approximation of the depletion regions and correctly predicts the sidewall threshold voltage shift and its saturation is discussed. The model makes it possible to measure the sidewall threshold even when it is larger than the front threshold voltage     

An assessment of the θ-projection method for the representation and extrapolation of creep data for a 1%Cr, 12%Mo, 14%V steel tested at 565°C

Constant stress creep data for a wrought 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel obtained from six tests carried out at 565°C have been fitted and extrapolated using the θ-projection method. Creep curves for high stresses were fitted well, but curves extrapolated to stress levels below those used in the θ-projection did not represent well the available data for primary-secondary creep. To enable a satisfactory extrapolation of results, it was found necessary to redefine the failure condition to be less sensitive to the shape of the latter sections of the tertiary creep curve. This was achieved by defining lifetime as the point on the curve at which the strain rate reached a fixed multiple of the creep rate at half the rupture time. The extrapolated data compare well with the results of tests carried out independently on a cast 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel. The extrapolation procedure not only predicts the ‘knee’ in the log stress-log lifetime curve but allows extrapolation of lifetimes by over a factor of thirty. In addition, acceptable predictions have been made of constant load experimental data.     

An efficient heuristic for scheduling batches of parts in a flexible flow system

Flexible manufacturing systems (FMSs) are a class of automated systems that can be used to improve productivity in batch manufacturing. Four stages of decision making have been defined for an FMS—the design, planning, scheduling, and control stages. This research focuses on the planning stage, and specifically in the area of scheduling batches of parts through the system.The literature to date on the FMS planning stage has mostly focused on the machine grouping, tool loading, and parttype selection problems. Our research carries the literature a step further by addressing the problem of scheduling batches of parts. Due to the use of serial-access material-handling systems in many FMSs, the batch-scheduling problem is modeled for a flexible flow system (FFS). This model explicitly accounts for setup times between batches that are dependent on their processing sequence.A heuristic procedure is developed for this batch-scheduling problem—the Maximum Savings (MS) heuristic. The MS heuristic is based upon the savings in time associated with a particular sequence and selecting the one with the maximum savings. It uses a two-phase method, with the savings being calculated in phase I, while a branch-and-bound procedure is employed to seek the best heuristic solution in phase II. Extensive computational results are provided for a wide variety of problems. The results show that the MS heuristic provides good-quality solutions.     

Preliminary model of the Ribeira Grande geothermal field (Azores Islands)

On the basis of a geological - volcanological - geophysical survey, integrated with petrological and geochronological data, a structural model, including a shallow magmatic body, was defined for the Ribeira Grande area, Sao Miguel island (Azores). Two series of production tests were carried out in the Pico Vermelho 1 and Ribeira Grande 1 wells, which led to a preliminary definition of the deep fluid circulation. The data obtained from these studies were used to reconstruct a preliminary model of the Ribeira Grande geothermal field.     

Surface tension isotherms of a free surface and grain boundaries in the Cu-Sn system

Surface tension of pure copper and its alloys with Sn has been measured at 1000°C in a hydrogen atmosphere. Surface tension of a free surface equaled 1.81 N/m for pure copper, and 1.55, 1.38, and 1.28 N/m for the alloys with 0.05, 0.22, and 0.33 at % Sn, respectively; surface tension at grain boundaries equaled 0.5 N/m for pure copper, and 0.36, 0.3, and 0.23 N/m for the alloys, respectively. Based on these data, the concentration dependence of tin absorption at a free surface and grain boundaries has been calculated. Parameters of Sn absorption at grain boundaries and a free surface of copper have been compared with those of Sb and Bi.