A comparative analysis of fuzzy logic and PI speed control in high-performance AC drives using experimental approach

One of the frequently discussed applications of artificial intelligence in motion control is the replacement of a standard proportional plus integral (PI) speed controller with a fuzzy logic (FL) speed controller. Regardless of all the work, it appears that a thorough comparison of the drive behavior under PI and FL speed control is still missing. This paper attempts to fill in this gap, by providing an in-depth comparison of operation of a vector-controlled permanent-magnet synchronous motor, using at first an experimental rig. Speed responses, obtained under PI and FL speed control, are recorded and compared for a variety of operating conditions. The transients studied include response to a large step speed command from standstill with nominal inertia and an increased inertia, response to small step speed reference change, and response to step load torque application. The transient behavior is examined for various initial speed settings, so that a thorough comparison is enabled. Experimental results are further supplemented with a set of simulation results, obtained using a different permanent-magnet machine and a different FL controller. Better generalization of the results is enabled in this way. It is shown that superiority of the FL speed control is less pronounced than it is often portrayed in the literature on the basis of limited comparisons. Indeed, in a number of cases, PI speed control provides a superior speed response.     

双塔脱丙烷工艺技术

对扬子乙烯装置双塔脱丙烷系统低压塔液泛、高压塔再沸器堵塞等问题进行了技术分析,提出了工艺流程修改方案,完善了双塔脱丙烷技术,对同类装置有参考价值。     

Photoelectric properties of planar structures with double Schottky barrier treated in a high-vacuum microwave discharge

The state of the surface of n-GaAs crystals upon high-vacuum microwave plasmachemical (HVMWPC) etching in various gas mixtures and the influence of the semiconductor surface condition on the photoelectric characteristics of related metal-semiconductor-metal structures with double Schottky barrier (MSMDSB structures) are investigated. Dependence of the HVMWPC etching rate of the GaAs surface on the gas mixture composition and substrate temperature is determined. It is shown that the HVMWPC etching regime strongly influences the photoelectric properties of MSMDSB structures: the treatment can lead to either growth or drop in photosensitivity of the samples. Optimum etching regimes are established for which good semiconductor surface quality and high photosensitivity of the MSMDSB structures are retained at a high etching rate.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Climatic solar roof: an ecological alternative to heat dissipation in buildings

A new system based on the harnessing of solar and wind power is presented for heat dissipation in air conditioning facilities. The innovation offered by the new system is the integration of two well-known subsystems: a cooling tower and a solar chimney which increases the air flow without the use of electric power. The system is described and presented together with a model for its study. The field data acquired from the prototype built in southern Spain establishes the actual potential of the system, which provides a new approach to a sustainable technological development.     

Parametric inference for step-stress models

Applications of the additive accumulation of damages (AAD) or the accelerated failure time (AFT) and the proportional hazards (PH) models in accelerated life testing with step-stresses are discussed. A new model including AAD and PH models is proposed. It is more reasonable than the PH model and wider then the AAD model. Constructing the maximum likelihood function is discussed     

Effect of Thermohydrogen Treatment on the Structure and Properties of Titanium Alloy Castings

Metal Science and Heat Treatment -     

Analysis of burn-in time using the general law of reliability

Empirical lifetime distributions sometimes have a bathtub-shaped failure rate. This paper deals with some models having a bathtub-shaped failure rate. The root-mean-square criterion is proposed for selection of the best model. Besides two criteria of optimum burn-in time are proposed. The comparison of some models with the general law of reliability is given to determine a burn-in time in a number of examples.