TiO2 promoted Co/SiO2 catalysts for Fischer–Tropsch synthesis

The addition of small amount of TiO₂ to silica-supported cobalt catalysts significantly increasing the dispersion of cobalt and Co metallic surface area resulting in the remarkable enhancement of the Fisher–Tropsch synthesis (FTS) activity in the slurry-phase reaction. The addition of TiO₂ adjusted the interaction between cobalt and silica support quite well to realize the favorite dispersion and reduction degree of supported cobalt, leading to high catalytic activity in FTS. The properties of various catalysts were characterized by in-situ DRIFT, XRD, TPR, N₂ physisorption and H₂ chemisorption.     

Effects of carbon source on denitrification efficiency and microbial community structure in a saline wastewater treatment process

Two different denitrifying reactors were monitored in order to evaluate the effects of carbon source on denitrification efficiency and microbial community structure under various saline conditions. Nitrogen removal performances were determined when salinity concentrations increase gradually in acetate- or methanol-fed denitrifying reactor. As a result, acetate-fed process attained high nitrate removal at 0-10% NaCl, while methanol was proven beneficial electron donors at 0-3% NaCl. A parallel analysis of T-RFLP and cloning in the acetate-fed sludge showed that a specialized microbial population (i.e. the genera Halomonas and Marinobacter) adapted to a high saline environment. Meanwhile, there were no major changes of bacterial populations in the methanol-fed reactor at 4% NaCl, although the relative abundances of the genera Azoarcus and Methylophaga increased when salinity concentration was at 1-3% NaCl, indicating that methanol-utilizing populations in activated sludge was unable to adapt to a high saline environments (>4% NaCl).     

Two-dimensional photonic crystal resist membrane nanocavity embedding colloidal dot-in-a-rod nanocrystals

A novel technique for the fabrication of photonic crystal (PC) nanocavities coupled with colloidal nanocrystals is presented. A waveguiding resist membrane embedding highly emitting dot-in-a-rod nanocrystals was patterned through e-beam lithography and released through wet etching process. The proposed approach makes the PC structure independent of fabrication imperfections induced by etching steps. Micro-photoluminescence spectra revealed degenerated resonant modes (Q-factor approximately 700) whose fabrication-induced spectral splitting is comparable to the full width at half-maximum of the peaks. Active nanocavities tunable from visible to infrared spectral range on GaAs or Si substrates can be easily implemented by this technique.     

Highly spin-polarized materials and devices for spintronics?

The performance of spintronics depends on the spin polarization of the current. In this study half-metallic Co-based full-Heusler alloys and a spin filtering device (SFD) using a ferromagnetic barrier have been investigated as highly spin-polarized current sources. The multilayers were prepared by magnetron sputtering in an ultrahigh vacuum and microfabricated using photolithography and Ar ion etching. We investigated two systems of Co-based full-Heusler alloys, Co₂Cr_{1 − x}Fe_xAl (CCFA(x)) and Co₂FeSi_{1 − x}Al_x (CFSA(x)) and revealed the structure and magnetic and transport properties. We demonstrated giant tunnel magnetoresistance (TMR) of up to 220% at room temperature and 390% at 5 K for the magnetic tunnel junctions (MTJs) using Co₂FeSi_0.5Al_0.5 (CFSA(0.5)) Heusler alloy electrodes. The 390% TMR corresponds to 0.81 spin polarization for CFSA(0.5) at 5 K. We also investigated the crystalline structure and local structure around Co atoms by x-ray diffraction (XRD) and nuclear magnetic resonance (NMR) analyses, respectively, for CFSA films sputtered on a Cr-buffered MgO (001) substrate followed by post-annealing at various temperatures in an ultrahigh vacuum. The disordered structures in CFSA films were clarified by NMR measurements and the relationship between TMR and the disordered structure was discussed. We clarified that the TMR of the MTJs with CFSA(0.5) electrodes depends on the structure, and is significantly higher for L2₁ than B2 in the crystalline structure. The second part of this paper is devoted to a SFD using a ferromagnetic barrier. The Co ferrite is investigated as a ferromagnetic barrier because of its high Curie temperature and high resistivity. We demonstrate the strong spin filtering effect through an ultrathin insulating ferrimagnetic Co-ferrite barrier at a low temperature. The barrier was prepared by the surface plasma oxidization of a CoFe₂ film deposited on a MgO (001) single crystal substrate, wherein the spinel structure of CoFe₂O₄ (CFO) and an epitaxial relationship of MgO(001)[100]/CoFe₂ (001)]110]/CFO(001)[100] were induced. A SFD consisting of CoFe₂ /CFO/Ta on a MgO (001) substrate exhibits the inverse TMR of - 124% at 10 K when the configuration of the magnetizations of CFO and CoFe₂ changes from parallel to antiparallel. The inverse TMR suggests the negative spin polarization of CFO, which is consistent with the band structure of CFO obtained by first principle calculation. The - 124% TMR corresponds to the spin filtering efficiency of 77% by the CFO barrier.     

Macroscale and microscale analyses of nitrification and denitrification in biofilms attached on membrane aerated biofilm reactors

A membrane aerated biofilm reactor (MABR), in which O(2) was supplied from the bottom of the biofilm and NH(4)(+) and organic carbon were supplied from the biofilm surface, was operated at different organic carbon loading rates and intra-membrane air pressures to investigate the occurrence of simultaneous chemical oxygen demand (COD) removal, nitrification and denitrification. The spatial distribution of nitrification and denitrification zones in the biofilms was measured with microelectrodes for O(2), NH(4)(+), NO(2)(-), NO(3)(-) and pH. When the MABR was operated at approximately 1.0 g-COD/m(2)/day of COD loading rate, simultaneous COD removal, nitrification and denitrification could be achieved. The COD loading rates and the intra-membrane air pressures applied in this study had no effect on the start-up and the maximum rates of NH(4)(+) oxidation in the MABRs. Microelectrode measurements showed that O(2) was supplied from the bottom of the MABR biofilm and penetrated the whole biofilm. Because the biofilm thickness increased during the operations, an anoxic layer developed in the upper parts of the mature biofilms while an oxic layer was restricted to the deeper parts of the biofilms. The development of the anoxic zones in the biofilms coincided with increase in the denitrification rates. Nitrification occurred in the zones from membrane surface to a point of ca. 60microm. Denitrification mainly occurred just above the nitrification zones. The COD loading rates and the intra-membrane air pressures applied in this study had no effect on location of the nitrification and denitrification zones.     

Physical Properties of Two Isomers of Conjugated Linoleic Acid

Thermal properties, powder X-ray diffraction patterns and FT-IR absorption spectra of crystals of two isomers of conjugated linoleic acid (CLA), 9-cis, 11-trans-CLA (c9t11), 10-trans, 12-cis-CLA (t10c12) were examined. To search for polymorphic modifications, we carefully performed crystallization from melt and solution phases, and isolated one type of crystalline form in c9t11 and t10c12. The melting temperature (T _m) was 14.9 °C, enthalpy of fusion (ΔH) was 38.7 kJ/mol, and entropy of fusion (ΔS) was 134 J/mol K for c9t11, and T _m = 19.8 °C, ΔH = 35.6 kJ/mol and ΔS = 122 J/mol K for t10c12. The X-ray diffraction and FT-IR measurements indicated O_⊥ subcell packing in the crystals of c9t11 and t10c12, and long spacing values of 4.22 nm for c9t11 and 3.88 nm for t10c12. The unique molecular structures of the two isomers of CLA are discussed in comparison to the polymorphism of oleic acid, petroselinic acid, elaidic acid and linoleic acid, all of which are unsaturated fatty acids having the same carbon number of 18 as that of the two CLA isomers.     

Striped‐pattern deterioration and morphological analysis of injection molding comprising polypropylene/ethylene–α‐olefin rubber blends. II. Influence of heating

Unique deterioration with a striped pattern caused by thermal heating is reported for injection molding comprising polypropylene/ethylene–α‐olefin rubber blends. This stripe is due to the formation of glossy and cloudy parts in alternation approximately perpendicular to the flow direction of the molten resin. On the surface of the cloudy part, a number of micro‐objects appear. They have a dome shape about 10 μm in diameter and 2 μm height. Some experimental evidence indicates that the objects are composed of the rubber contained in the blends. On the other hand, only a few objects appear in the glossy region after heating. This is the reason that the stripe with the micro‐objects (migrating rubber to the surface) is examined in terms of a higher order structure of injection molding with laser scanning microscopy, wide‐angle X‐ray scattering, and microhardness (Martens hardness). Consequently, we have concluded that this thermally deteriorated stripe depends on periodic changes in the crystallinity along the flow direction. The evidence indicates that a snakelike flow occurs during the injection process of the molding. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Architecture of rod consisting of hyperbranched pendant chains‐coil block copolymers by ATRP approach

Atom transfer radical polymerization (ATRP) was applied to a novel synthesis of rod consisting of hyperbranched pendant chains‐coil block copolymers. The procedure included the following steps: (1) esterification reaction of poly(ethylene glycol) methyl ether (PEO) with 2‐bromoisobutyryl bromide (BIBB) yielded a PEO‐Br macroinitiator, (2) ATRP method of 2‐hydroxylethyl methacrylate (HEMA) using PEO‐Br provided PEO‐block‐poly(2‐hydroxyethyl methacrylate) (PHEMA) block copolymers, (3) esterification of PEO‐block‐PHEMA with BIBB yielded block‐type polyinitiator, and (4) ATRP of HEMA‐Br inimer using block‐type polyinitiator provided coil‐rod (consisting of hyperbranched pendant chains) block copolymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Homofarnesals: Female Sex Attractant Pheromone Components of the Southern Cowpea Weevil, <Emphasis Type="Italic">Callosobruchus chinensis</Emphasis>

The southern cowpea weevil, Callosobruchus chinensis (Coleoptera: Bruchidae), is a major pest of stored legumes in warm temperate and tropical climates. The female sex attractant pheromone was extracted from filter-paper shelters taken from containers that housed virgin females. The extracts were purified by various chromatographic techniques, and the biologically active components in the fractions were screened by gas chromatographic–electroantennographic detection analysis with male antennae. Two compounds that elicited electrophysiological responses were isolated, and gas chromatography–mass spectrometry, nuclear magnetic resonance, and micro-chemical analyses suggested that the active compounds were homofarnesals, (2Z,6E)- and (2E,6E)-7-ethyl-3,11-dimethyl-2,6,10-dodecatrienals. Males of C. chinensis were significantly attracted to filter paper discs loaded with the synthetic compounds at 0.01–0.1 ng compared to solvent control in a Y-tube olfactometer assay. These pheromone components represent unique chemical structures within the genus Callosobruchus.