A Nonvolatile Organic Memory Device Using ITO Surfaces Modified by Ag‐Nanodots

We report on a single‐layer organic memory device made of poly(N‐vinylcarbazole) embedded between an Al electrode and ITO modified with Ag nanodots (Ag‐NDs). Devices exhibit high ON/OFF switching ratios of 10⁴. This level of performance could be achieved by modifying the ITO electrodes with some Ag‐NDs that act as trapping sites, reducing the current in the OFF state. Temperature dependence of the electrical characteristics suggest that the current of the low‐resistance state can be attributed to Schottky charge tunnelling through low‐resistance pathways of Al particles in the polymer layer and that the high‐resistance state can be controlled by charge trapping by the Al particles and Ag‐NDs.     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

A growth control approach to Class II, Division 1 cases during puberty involving the simultaneous application of maxillary growth restriction and mandibular forward induction

A simple method that used headgear and a functional appliance simultaneously was used for the correction of Class II, Division 1 cases with severe denture base discrepancy. The treatment restricted the forward growth of the maxilla and advanced the mandible. The functional appliance, referred to as the mandibular growth advancer (MGA), advances the mandible progressively with a splint, with the objective of remodeling the condyle and the glenoid fossa in the temporomandibular joint. Functional adaptation was achieved as the muscles that are attached to the mandible adjusted to new positions. In the two cases that illustrate this method, the ANB angle decreased and the Ar-B distance increased over a short period to four and six times the mean Japanese growth rate, respectively. After the correction of the denture-base discrepancy, a multibracket fixed appliance was used for dental alignment, and good skeletal, occlusal relationships and profiles were obtained. Treatment of severe denture-base discrepancy in this manner may reduce the skeletal abnormality, decrease the number of extraction cases, and shorten the subsequent multibracket treatment time. And it may reduce the iatrogenic side effects caused by prolonged mechanotherapy with a fixed appliance.     

An equation of state for 1,1-difluroethane (HFC 152a)

An equation of state for 1,1-difluoroethane (HFC 152a, CH₃CHF₂) has been developed on the basis of reliable experimental data including PVT, liquid C_p, and saturated-liquid-density data measured by our group. It is a non-dimensionalized virial equation whose functional form is the same as that originally developed for 1,1,1,2-tetrafluoroethane (HFC 134a) in our group. The effective range is for pressures up to 15 MPa, temperatures from 230 to 450 K, and densities to 1000 kg m⁻³. The equation represents reliable PVT measurements within ± 1% in pressure for the superheated vapour and supercritical fluid, while within ±0.5% in density for the compressed liquid. In addition, it should be noted that the equation represents the other essential thermodynamic properties including vapour pressures, saturated-liquid/ vapour densities, isobaric/isochoric specific heats and sound velocity in both the liquid and gaseous phase of HFC 152a.     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

The gamma-ray-induced crosslinking of polyacrylamide

The gamma-ray-induced crosslinking of polyacrylamide was carried out under various conditions. The molecular weight of the polymer before inrradiation was found to be the most important factor for crosslinking. When polymers have low molecular weights such as 80,000, the intensity of radiation, the external pressure applied, and the water content of the polymer powder became important for crosslinking. Although the polycrylamide hydrogel can be obtained directly by irradiating the monomer, it was obtained more conveniently by the irradiation of monomer—polymer mixtures. The hydrogels obtained by the radiation with a dose of over 50 kgray, absorb water by 1000–1500 wt %.     

Development of a distributed sensing technique using Brillouinscattering

This paper reviews the developments of a distributed strain and temperature sensing technique that uses Brillouin scattering in single-mode optical fibers. This technique is based on strain- and temperature-induced changes in the Brillouin frequency shift. Several approaches for measuring the weak Brillouin line are compared