Shear viscosity of rubber modified thermoplastics: Dynamically vulcanized thermoplastic elastomers and ABS resins at very low stress

The shear viscosity of PP-EPDM dynamically vulcanized thermoplastic elastomers and ABS resins were investigated using (a) a constant shear stress creep instrument, (b) a rotational rheometer, and (c) a capillary extrusion rheometer. It was found that stresses exist for some of these materials below which they exhibit only finite deformations. This indicates they exhibit yield values. Much attention was given to measurements of creep at low stresses especially in the neighborhood of yield values. The magnitudes of the yield stresses obtained from these low stress measurements are significantly lower than those obtained using standard extrapolation to zero shear rate of higher stresses from rotational instruments. We also observed a high shear viscosity (～10⁹ PA s) plateau in the materials of high rubber content. We contrasted our results to those found in the literature.     

Solidification of Al2O3–YAG eutectic composites with off-metastable eutectic composition from undercooled melt produced by melting Al2O3–YAP eutectics

It has been reported that solidification of the Al₂O₃–YAG equilibrium eutectic structure follows melting of the Al₂O₃–YAP metastable eutectic structure. Since the exothermic heat due to solidification was consumed by the endothermic heat due to melting, a fine and uniform eutectic structure was obtained. However, the composition of the Al₂O₃–YAG eutectic structure is restricted to the metastable eutectic composition. In this paper, Al₂O₃–YAG eutectic compacts with an off-metastable eutectic composition were prepared by the addition of Al₂O₃ particles to Al₂O₃–YAP eutectic particles with diameters less than 20 μm. In compositions ranging from 18.5 mol%Y₂O₃ to 13.5 mol%Y₂O₃, dense Al₂O₃–YAG eutectic compacts were formed without any Al₂O₃ segregation. The flexural strength and the fracture toughness remained almost unchanged with the increase in the Al₂O₃ phase. The addition of Al₂O₃ particles to the Al₂O₃–YAP eutectic particles enabled the matrix phase to change from the YAG phase to the Al₂O₃ phase.     

Performance improvement of the filter-type ‘transXend’ energy-resolving detector by considering noise sensitivity

The filter-type ‘transXend’ detector is an energy-resolving X-ray detector consisting of an energy-integrating flat-panel detector and multiple filters. In our previous studies, we have shown the effectiveness of the transXend detector, but the filters used were not optimized. To obtain better performance, the filters, especially their thickness and material, should be considered. In this paper, we present a method that can preliminarily estimate filter performance by comparing their noise sensitivity before carrying out numerous experiments. Two kinds of filter sets, Cu–Sn and W–Ag, with various thicknesses were evaluated. The results suggest that to image a 20-cm-thick object with 120-kV X-rays, an unfiltered channel and a channel filtered with 0.5-mm-thick Sn or 0.4-mm-thick Ag may be the best combination. The optimal filter thickness will be smaller if the object is thinner and the tube voltage is lower. For applications that require a wide dynamic range of detector response, a channel with a W filter may be better than an unfiltered channel. To verify the calculation results, computed tomography imaging experiments with a 3-cm-diameter phantom were also performed, and the experimental results showed good agreement with the calculation results.     

Terpendole E and its Derivative Inhibit STLC‐ and GSK‐1‐Resistant Eg5

Terpendole E is first natural product found to inhibit mitotic kinesin Eg5, but its inhibitory mechanism remains to be revealed. Here, we report the effects of terpendole E and 11ketopaspaline (a new natural terpendole E analogue) on the Eg5–microtubule interaction and in several Eg5 mutants. 11‐Ketopaspaline is a shunt product from terpendole E, and it shows potent inhibitory activity against the microtubule‐stimulated ATPase activity of Eg5. Unlike other Eg5 inhibitors, such as S‐trityl‐L ‐cysteine (STLC) and GSK‐1, both terpendole E and 11‐ketopaspaline only partially inhibited Eg5–microtubule interaction. Furthermore, terpendole E and 11‐ketopaspaline inhibited several Eg5 mutants that are resistant to STLC (Eg5^D130A, Eg5^L214A) or GSK‐1 (Eg5^I299F, Eg5^A356T), but with the same extent of inhibition against wild‐type Eg5. Because Eg5^D130A and Eg5^L214A show cross‐resistance to most known Eg5 inhibitors, which bind the L5 loop, these results suggest that terpendole E and its analogues have a different binding site and/or inhibitory mechanism to those for L5 loop‐binding type Eg5 inhibitors.     

Tetrahydropyranyl- and furanyl-protected polyhydroxystyrene in chemical amplification systems

Tetrahydropyranyl- (THP) and furanyl- (THF) protected polyhydroxystyrene (PHS) polymers have been investigated for their potential use in conjunction with onium salt acid precursors to yield high-sensitivity resist systems. The synthesized polymers have high transmittance at 248 nm (the wavelength used in next-generation excimer laser, KrF exposure tools). At 248 nm the transmittance for a 1-μm thick film is ～ 80% (Abs = 0.097 μm^?1). The acid sensitivity of the acetal functionality at room temperature is high, requiring careful handling of all materials to prevent any premature deprotection of the hydroxy group. The highest lithographic sensitivities obtained so far with a system consisting of poly(p-tetrahydropyranyl-oxy-styrene) base resin and 1 mol % of bis (p-tert-butyl phenyl) iodinium triflate (TBIT) was ～ 2 mJ / cm². High-resolution line and space patterns (0.35 μm) were obtained with a system comprising PHS-p-THP and an acid precursor, using an excimer laser step and repeat exposure at 248 nm.     

The Creep and Thermal Stability Characteristics of a Unidirectionally Solidified Al2O3/YAG Eutectic Composite

Compressive creep characteristics at 1773, 1873, and 1973 K, oxidation resistance over 1000 h at a temperature of 1973 K in ambient air, and the thermal stability characteristics at 1973 K in ambient air of a unidirectionally solidified Al2O3/YAG eutectic composite were evaluated. At a test temperature of 1873 K and a strain rate of 10–4/s, the compressive creep strength of a eutectic composite manufactured by the unidirectional solidification method is approximately 13 times higher than that of a sintered composite with the same chemical composition. The insite eutectic composite also showed greater thermal stability, with no change in mass after an exposure of 1000 hours at 1973 K in ambient air. The superior high-temperature characteristics are closely related to such factors as (1) the in-situ eutectic composite having a microstructure, in which single crystal Al2O3 and single crystal YAG are three-dimensionally and continuously connected and finely entangled without grain boundaries and (2) no amorphous phase is formed at the interface between the Al2O3 and the YAG phases.     

Application of a Two-Dimensional Computer Simulation to Cake Growth in Slip Casting with Complicated-Shape Gypsum Molds

A two-dimensional computer simulation method, developed by the authors using the method of finite differences, was applied to estimate the cake growth in slip casting of alumina with a triangular gypsum mold and a box-type gypsum mold with a convex bottom. The cake growth patterns, water penetration patterns, water flow rate distributions, and pressure distributions were simulated in the molds and/or cakes. The simulated cake growth patterns were in good agreement with those observed experimentally in both molds. Moreover, the cake growths could be well understood from the results of the water flow rate distributions in each case. The present method is applicable to cake growth simulation in slip casting with complicated-shape gypsum molds.     

Tactic poly(crown ether)s with pendant benzocrown ethers

Summary Tactic and atactic poly(crown ether)s, poly(methacryloyloxymethylbenzo-15-crown-5), were synthesized by polymer reaction of the respective poly(methacrylic acid) with chloromethylbenzo-15-crown-5 and radical polymerization of methacryloyloxymethylbenzo-15-crown-5. By solvent extraction of alkali metal picrates with these poly(crown ether)s, the isotactic poly(crown ether) was found to be a little more selective for K⁺ and Rb⁺ than the syndiotactic and atactic ones.     

The Leaching of Hematite in Acid Solutions

The reactions of hematite in aqueous hydrochloric acid, perchloric acid, and sulfuric acid solutions with or without the addition of common or uncommon salts were studied using monosized particulates in a well-stirred reactor and dilute solid concentration to obtain fundamental details of the reaction kinetics. The experimental rate data suggest that the entire leaching reaction is controlled by a chemical process. The leaching rate of hematite was seen to be first order with respect to hydrogen ion activity, a(H⁺), in hydrochloric acid or perchloric acid solutions, with or without the addition of common salts, while the rate was of a half order in sulfuric acid solutions with or without the addition of sodium sulfate. A theoretical analysis showed that the anions next to the surface in the double layer were chloride ion and perchlorate ion in hydrochloric acid and perchloric acid solutions, respectively, and sulfate ion in sulfuric acid solutions, with or without the addition of sodium sulfate. The fact that the leaching rates of hematite were quite different in various acids having identical α(H⁺ values indicates the importance of anion adsorption. The dependency of the leaching rate upon α(H⁺) appeared to be controlled by adsorbed anions next to the surface in the double layer. TAKUMI MISHIMA, formerly Graduate Student, Kyoto University