Influence of physical relaxation on chemical stress–relaxation of natural rubber vulcanizates

Networks were prepared in the swollen and dry states to investigate the influence of physical relaxation on chemical stress–relaxation. The stress–relaxation behavior of solution-cured samples was different significantly from that of the samples crosslinked conventionally. The same result was also observed in the number of chain scission for both kinds of samples. On the other hand, the number of chain scission estimated by using the swelling method for samples crosslinked conventionally was in good agreement with that by the chemical stress–relaxation for solution-cured samples. It was found that there is little or no influence of the physical relaxation caused by entanglements, and no effect of dangling chains arising from scission in the equilibrium swelling. The relative change of network chain density determined by means of the swelling method was also consistent with that by sol fraction determination. These results indicate that the swelling method can be used as a measure of a degree of degradation on chemorheology. Taking into account the influence of physical relaxation on chemical stress–relaxation, a new relationship between the relative stress decay and the relative network chain density was experimentally proposed.     

Interdiffusion in copper-rich cu-ag solid solutions

Interdiffusion was studied in the temperature between 974 and 1273 K, using conventional sandwich-type diffusion couples consisting of pure copper and Cu-2.1 at. pct Ag alloy. The interdiffusion coefficient, , increased slightly with increasing the atomic fraction of silver, N_Ag. Values of were well represented by the parameters of ₀ = 0.21 x 10^-4 (m²/s) and ≈ = 184.5 - 143.0 N_Ag (kJ/g-atom) up toNAg = 0.02. The Kirkendall effect during diffu-sion treatments at 1174 K for up to 1.4724 x 10⁶ s was also studied. The marker moved always toward the silver-rich side. The ratio, D*_Ag / D*_Cu,was 5.6 for N_Ag = 0.011, while it was 4.2 for N_Ag = 0.     

Co40Ni33.5Al26.5合金马氏体相变、磁性与淬火温度的关系

Co-Ni-Al合金不仅可以作为铁磁性形状记忆合金,也是传统和高温形状记忆合金的候选材料,本文通过金相显微分析,DSC和VSM方法,研究了Co40Ni33.5Al26.5合金马氏体相变和Curie点随淬火温度变化的情况,结果发现该合金马氏体相变温度和Curie点与淬火温度成正比关系.马氏体相变的4种温度,即Ms、Mf、As和At基本平行变化,淬火温度每升高10℃,马氏体相变温度升高8～9℃,而Curie点升高6～7℃.其马氏体相变温度和Curie点随淬火温度的变化与基体相β的成分变化有关,β相中Al的含量随淬火温度升高而降低,因而马氏体相变温度和Curie点升高.并且发现随着淬火温度升高,Co40Ni33.5Al26.5合金马氏体相的磁晶各向异性有减弱的倾向.     

The use of phase diagrams and thermodynamic databases for electronic materials

Phase diagrams and a thermodynamic database constructed by the Calculation of Phase Diagrams approach offer powerful tools for alloy design and materials development. This article presents recent progress on the thermodynamic database for microsolders and copper-based alloys, which is useful for the development of lead-free solders and prediction of interfacial phenomena between solders and the copper substrate in electronic packaging technology. In addition, examples of phase diagram applications are presented to facilitate the development of Co-Cr-based magnetic recording media in hard disks and new ferromagnetic shape-memory alloys. For more information, contact K. Ishida, Tohoku University, Department of Materials Science, Graduate School of Engineering, Aoba-yama 02, Sendai 980-8579, Japan.     

Nonreentrant supraventricular tachycardia due to double ventricular response via dual atrioventricular nodal pathways

In twenty eight patients with iron deficiency the efficacy of iron-acetil-transferrin treatment (2-3 mg/kg/die) has been evaluated from the changes of the following variables: RBC and reticulocyte count, Hb concentration, MCV, MCH, serum ferritin, serum iron, TIBC, and ZnPP. These variables were assessed before and after three months of treatment in all patients, and after three months from the end of the treatment in thirteen patients. At the end of the treatment there was a significant increase of RBC count, Hb concentration, MCV, MCH, serum ferritin, serum iron, and TIBC, a significant decrease of ZnPP, while reticulocyte count remained essentially unchanged. After three months from the end of the treatment only serum ferritin and ZnPP underwent an additional significant increase and decrease, respectively. In twenty-six patients serum ferritin values returned to normal. The changes of RBC and reticulocyte count, Hb concentration, MCV, serum iron, and TIBC were larger the lower the initial values, suggesting that the efficacy of the treatment is greater the more serious the iron deficiency.     

A Method for Received Waveform Reconstruction Based on Bender Element Test Using Frequency-swept Signal

An experimental technique for reconstructing the received wave of bender element tests based on linear system theory is shown in this paper. In order to identify the frequency response of testing apparatus, bender element tests using frequency-swept signals are performed. Received waves for one-period sine pulse transmitting with various frequencies are calculated and compared with observed waves in several kinds of soil samples and testing apparatuses. The linearity of the testing system is also confirmed by coherence function. It is shown that calculated data are less affected by random noise and show good agreement with observed data in regards to not only waveform itself but also resulting shear wave velocity. It is mentioned that this technique can provide simulations for arbitrary transmitted waveform with high signal/noise ratio after laboratory tests are performed. It is also mentioned that this technique is advantageous when sufficient amplitude of received wave cannot be ensured or shear wave velocity must be verified, for example, due to uncertainty of arrival time by near-field effect.     

Study on high performance ice slurry formed by cooling emulsion in ice storage (discussion on adaptability of emulsion to thermal storage material)

This study focuses on an emulsion as a new thermal storage material for ice storage. Two types of emulsions were formed using an oil–water mixture with a small amount of additive. A silicone, light and lump oils were used. The water contents of the emulsions were 70, 80 and 90%. The additive was an amino group modified silicone oil. No depression of freezing point was observed for the emulsions because of their hydrophobic properties. In order to determine the structure of the emulsions, their electrical resistances were measured. Moreover, components of the liquids separating from the emulsions were analyzed. The results indicated that one emulsion was a W/O type emulsion, while the other was an O/W type. Finally, adaptability of the two emulsions to ice storage was discussed, it was concluded that a high performance ice slurry could be formed by the W/O type emulsion.     

Development of systems reliability analysis code SECOM-2 for seismic PSA

An integrated code system SECOM-2, developed at the Japan Atomic Energy Research Institute (JAERI), has the following functions for systems reliability analysis in seismic probabilistic safety assessments (PSAs): (1) calculation of component failure probability, (2) extraction of minimal cut sets (MCSs) from a given fault tree (FT), (3) calculation of frequencies of accident sequences and core damage, (4) importance analysis with several measures with consideration of unique parameters of seismic PSAs, (5) sensitivity analysis, and (6) uncertainty analysis. This paper summarizes the special features of SECOM-2 to perform the analyses mentioned above. At JAERI, using an integrated FT which represents seismically induced core damage due to all initiating events as a system model to calculate core damage frequency of a nuclear power plant, SECOM-2 can calculate conditional point estimate probabilities of system failures, losses of safety functions, and core damage as a function of earthquake motions. The point estimate is computed by a method which gives an exact numerical solution using the Boolean arithmetic model method. As for consideration of correlation of component failure, which has been an important issue in seismic PSAs, a new technique based on direct FT quantification by a Monte Carlo simulation is being added to SECOM-2. Adding this technique, the core damage frequency can be calculated not only with the upper bound approximation based on MCSs but also with a near exact solution taking into account the correlation among all components. This paper also presents the preliminary results of a seismic PSA of a generic BWR plant in Japan performed at JAERI to demonstrate the functions of the SECOM-2 code.