Sub-millimeter-long carbon nanotubes repeatedly grown on and separated from ceramic beads in a single fluidized bed reactor

A semi-continuous fluidized-bed process is reported which rapidly converts acetylene into carbon nanotubes (CNTs). Catalysts are first immobilized on ceramic beads and CNTs are then grown on the beads and then separated from them in a repetitive process accomplished within a single reactor simply by switching gases at a fixed temperature. CNTs of 6–10 nm diameter, three walls on average, 0.4 mm length and 99 wt.% purity were synthesized at an yield of over 70% in a reactor residence time shorter than 0.3 s. The easy and efficient production of such CNTs with in situ separation from the catalysts may accelerate the development of CNT-based nanotechnology industries.     

Improved methodology for the simultaneous detection of the trichothecene mycotoxins deoxynivalenol and nivalenol in cereals

A simple and sensitive method has been developed for the analysis of two trichothecene mycotoxins (deoxynivalenol and nivalenol) in cereals. These toxins were extracted with acetonitrile/water (3:1), defatted with n-hexane and purified by a two-step chromatographic procedure using Florisil and Sep-pak columns. The amounts of deoxynivalenol (DON) and nivalenol (NIV) in the column eluates were quantitated by gas chromatography with electron capture detector and gas chromatography-mass spectrometry (selected ion monitoring). The limits of detection of the method were 2.0 micrograms/kg for DON and NIV with recoveries of the toxins spiked into polished rice, wheat and corn at 300 micrograms/kg averaging 87% and 86% respectively.     

γ‐Butyrolactone‐processable high‐modulus poly(ester imide)s

γ‐Butyrolactone (GBL)‐processable high modulus heat‐resistant materials were developed in this work. The polyaddition of an ester‐containing tetracarboxylic dianhydride, i.e. hydroquinone bis(trimellitate anhydride) (TAHQ), and 2,2′‐bis(trifluoromethyl)benzidine (TFMB) in GBL resulted in gelation in the initial reaction stage. The incorporation of a methyl group to TAHQ (M‐TAHQ) allowed polymerization with TFMB in GBL and led to a homogeneous poly(ester imide) (PEsI) precursor solution with a short pot life of 3 days, whereas a simple copolymerization approach using bulky/flexible comonomers to TAHQ/TFMB was less effective. PEsI precursors (PEsAAs) were prepared from TFMB, M‐TAHQ and a minor fraction of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride (6FDA) or a fluorene‐containing tetracarboxylic dianhydride. These PEsAA systems showed drastically improved GBL solution stability. In particular, the M‐TAHQ(80);6FDA(20)/TFMB copolymer system provided a PEsAA film with a very high light transmittance at 365 nm (>70%). A photosensitive film composed of this matrix resin and diazonaphthoquinone provided a clear positive‐tone pattern by development in a 2.38 wt% tetramethylammonium hydroxide aqueous solution at room temperature with a high dissolution contrast. The thermally cured PEsI film achieved a very high tensile modulus (>5 GPa) as the present target with other desirable properties, i.e. sufficient film flexibility, a relatively low coefficient of thermal expansion, a high T_g and low water absorption. The present materials can be promising candidates as novel buffer coat films in semiconductor applications. Copyright © 2011 Society of Chemical Industry     

Forced convective heat transfer to supercritical water flowing in tubes

Experimental investigations were made of heat transfer to supercritical water flowing in a horizontal tube and vertical tubes. A comprehensive set of data was obtained for pressures from 226 to 294 bar, bulk temperatures from 230 to 540°C, heat fluxes from 116 to 930 kW/m² and mass velocities from 310 to 1830 kg/m²s. Because the physical properties of supercritical fluids change rapidly with temperature in the pseudocritical region, the heat transfer coefficients show unusual behavior depending upon the heat flux. At low or modetate heat fluxes relatively to the flow rate, a satisfactory correlation was obtained, which predicts reasonably well the enhanced heat transfer coefficients near the pseudocritical point. The several characteristics of the deterioration in heat transfer which occurs at high heat fluxes were clarified, and the limit heat flux for the occurrence of the deterioration was determined in connection with the flow rate.     

Starting method of a superconducting generator in a combined‐cycle power plant

In the combined‐cycle power plant generators are started by using the igniting arrangement up to the ignition rotational speed of the gas turbine. On the other hand, in the case of using the superconducting generator, it is difficult to apply the igniting arrangement used to generate electricity on the combined cycle for the structure as is. We examined the induction motor starting method for the superconducting generator by using the 70‐MW‐class quick‐response excitation superconducting model generator and the VVVF power supply. From the examination, we confirmed the ability to raise the rotational speed from 6 to 360 rpm. Moreover, it was found to be able to start 200‐MW‐class superconducting generators by the induction motor starting method with the analysis. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(2): 30– 38, 2007; Published online in Wiley InterScience ( www.interscience. wiley.com ). DOI 10.1002/eej.20283     

A new technique to measure the temperature of a rotating motor shaft

In the present study, a new technique has been developed for the measurement of the temperature of a motor shaft rotating at high speed. A radiation thermometer could be useful as one of the methods of measuring the surface temperature of said shaft. However, if the cross-sectional diameter of the motor shaft is small, it is necessary to closely approach the shaft rotating at high speed when measuring the temperature. The present paper reports the successful measurement of the local surface temperature and the temperature rise time of a motor shaft with a diameter of 10 mm diameter, rotating at high speed, by utilizing the potential of the melting points of different chemical reagents. The measurements were carried out at a distance of 1 m from the shaft, overcoming the difficulty in the use of a radiation thermometer.     

A High-Speed Optical Data Highway for Industrial Control Systems

Recent application of distributed control systems to large-and medium-scale industrial plants requires effective and high-speed communication among the control devices each other to ensure high-performance operation.     

Algorithms for planning and control of robot motions [TC Spotlight]

Robot motion planning and control is an essential component in creating autonomous systems that are able to execute high-level tasks for navigating and manipulating objects in challenging environments. Motion planning has led to active research over the past decades. Most of the research focused on the computational issue of generating feasible paths that lead the robot to a desired goal, while generally ignoring control concerns such as feedback, optimum, and uncertainty. The breakthrough achieved with sampling-based algorithms leads to effective techniques for hard, high-dimensional problems, and the recent improvements brought motion-planning algorithms closer to applicability in real problems. Nowadays, the practical interest of the state-of-the-art techniques is no longer restricted to robotics but extends to challenging problems arising in such diverse fields as graphics animation, virtual prototyping, and computational biology.