Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

A study on hydrogen storage by use of cryoadsorbents

This paper reports investigations on the techniques and economics of hydrogen storage by means of cryoadsorption. Also a comparison with alternative storage methods is included. The hydrogen storage capacity of several adsorbents in the temperature range 65–150 K has been investigated experimentally. Based on these data, economics and operating conditions for minimum total costs of the system are calculated. Utilization-factor and capacity-factor parameters are shown to be decisive for outlining the favourable ranges of application for competitive hydrogen storage methods.     

Computer aided design and new manufacturing methods for electronic materials

The world-wide sales for silicon integrated circuits totalled some £3,500M in 1980. The high growth rate of the industry is generated by high levels of investment in research, development and capital equipment leading to rapid innovation in design and manufacturing methods. This article concentrates on the increasing use of computers in the design process, new design concepts and the efforts to make the components within the silicon chip even smaller.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

The Aleph data acquisition system

Aleph is one of the four large high-energy physics experiments being completed for the LEP (Large Electron Positron) accelerator at CERN. Several hundred thousand detector elements deliver some 500 Mbytes of raw data per second. The author briefly describes the accelerator and the Aleph detector. He then discusses the design and implementation of the multilevel real-time data reduction and acquisition system, covering the requirements, the readout architecture, its implementation, data reduction, aspects of the detector-specific front-end electronics, and Aleph's present status and performance     

Approximate channel identification via δ‐signed correlation

A method of approximate channel identification is proposed that is based on a simplification of the correlation estimator. Despite the numerical simplification (no multiplications or additions are required, only comparisons and an accumulator), the performance of the proposed estimator is not significantly worse than that of the standard correlation estimator. A free (user selectable) parameter moves ‘smoothly’ from a situation with small sum‐squared channel estimation error but hard‐to‐identify channel peaks, to one with a larger sum‐squared estimation error but easy‐to‐identify channel peaks. The proposed estimator is shown to be biased and its behaviour is analysed in a number of situations. Applications of the proposed estimator to sparsity detection, symbol timing recovery and to the initialization of blind equalizers are suggested. Copyright © 2002 John Wiley & Sons, Ltd.     

Hydrogenation of canola oil in the presence of nickel and the methyl benzoate-chrome carbonyl complex

Canola oil was hydrogenated using a mixture of homogeneous methyl benzoate-Cr(CO)₃ and heterogeneous nickel catalysts. The effect of the methyl benzoate-Cr(CO)₃_to-nickel ratio on the activity, specific isomerization index, linoleate and linolenate selectivities, and fatty acid composition was evaluated, and the results compared with those obtained with commercial nickel catalyst and methyl benzoate-Cr(CO)₃ used individually. At higher chromium-to-nickel ratios the activity of nickel was inhibited and the system behaved essentially like the pure chrome complex, while at low chromium-to-nickel ratios the characteristics of the nickel predominated. In a short transition zone relatively high reaction rates were obtained with significantly reducedtrans-isomer levels in the product. In a broader sense, it may be possible to combine a homogeneous and heterogeneous catalyst while retaining the advantages of both. We may thus be able to design catalyst systems for specific applications.