Hydrogen absorption by Pd-coated ZrNi prepared by using Barrel-Sputtering System

To improve the durability of hydrogen storage materials against surface poisoning by impurity gases, effectiveness of Pd-coating layer prepared by using a Barrel-Sputtering System was examined for ZrNi powder. The effectiveness of Pd-coating was evaluated by activation temperature, at which Pd/ZrNi poisoned by air could be activated to absorb hydrogen. Characterization of Pd-coated ZrNi (denoted as Pd/ZrNi) by scanning electron microscopy, electron probe microanalysis and X-ray diffraction showed that a uniform Pd-coating layer was formed with the barrel-sputtering system. It was found that the poisoned Pd/ZrNi sample could be activated even at 423 K to absorb hydrogen at room temperature. This exhibits remarkable contrast to bare ZrNi, which could be only activated appreciably above 1073 K. It is concluded that the Pd-coating by barrel sputtering is quite effective to avoid the effect of surface poisoning of powdery hydrogen storage materials. However, the activation at excessively high temperature resulted in the loss of high activity to absorb hydrogen. It was concluded that this phenomenon was associated with reactions between Pd and ZrNi to form PdZr and other byproducts.     

The material properties of sulphonated phenolic resin reinforced cement mortars

The material properties of new sulphonated phenolic resin (SP) reinforced cement mortars have been investigated. SP was found to promote the dispersion of cement particles and to interact with Ca(OH)₂. As a result, the resulting mortars exhibit better workability, more compact structure and higher compressive strength than plain mortars. The mortar with 1 wt% SP present after 28 days curing exhibits a compressive strength of 66MPa, which is about 18% higher than that of plain mortar.     

Computer processing of artifact and arrhythmias in heart rate variability analysis.

Analysis of heart rate variability (HRV) with Holter monitoring is often difficult due to excessive artifacts and arrhythmias. While short sudden surges are treated successfully by most methods, slow heart rate (HR) variations, nocturnal trapezoidally-shaped HR increases and special types of arrhythmias which are similar to normal HRV fluctuations may distort further time domain and spectral analysis. This paper examines the advantages and disadvantages of different methods for preprocessing of HR data. We have developed the following approach to the analysis of HRV. (1) A combination method based on the absolute difference between HR values and both the last normal HR value and an updated mean is used for removal of artifacts and arrhythmias. This method can detect both sudden surges in HR values as well as longer periods of noise combined with slow normal variations. An additional stage of wild point removal is then optionally applied. (2) Certain special problems such as large T-waves, bigeminal rhythm, slow HR variations and nocturnal trapezoidally-shaped HR increases are also identified. Although none of the algorithms can be applied successfully to all cases, the final computer analysis for preprocessing described in the present study has proved to be superior to the simplified methods which are usually used and provides more suitable data for HRV analysis.     

A hybrid wafer-dicing process for GaAs MMIC production

A dicing process for GaAs MMIC (monolithic microwave integrated circuit) wafers using spin-on wax for wafer mounting and a hybrid process of wet chemical etching/mechanical sawing for chip dicing is described. This process minimizes ragged chip edges and reduces generation of microcracks in addition to the elimination of the plated gold burrs on the backside of the diced MMIC chips. This process gives a uniformity of -3 μm across a 2-in wafer following the completion of the whole backside process. This GaAs chip dicing technique is amenable to production because it exhibits both a very high chip yield (>90%) and nearly flawless edges     

Development of a distributed sensing technique using Brillouinscattering

This paper reviews the developments of a distributed strain and temperature sensing technique that uses Brillouin scattering in single-mode optical fibers. This technique is based on strain- and temperature-induced changes in the Brillouin frequency shift. Several approaches for measuring the weak Brillouin line are compared     

Transmission distance of in-line amplifier systems withgroup-velocity-dispersion compensation

Group-velocity dispersion (GVD) compensation in in-line amplifier systems is evaluated from the viewpoint of improving the transmission distance. The nonlinear Schrodinger equation, which simulates signal propagation in optical fibers, is numerically evaluated to clarify the optimum configuration for GVD compensation. It is shown that the optimum amount of GVD compensation is about 100% of the GVD experienced by the transmitted signal. The optimum compensation interval is found to be a function of the bit rate, signal power, and dispersion parameter. For dispersion parameter values ranging from about -0.1 ps/nm/km to -10 ps/nm/km, and an amplifier noise figure of about 6 dB, the optimum compensation configuration can eliminate the GVD from in-line amplifier systems, thus improving transmission distances to those limited by self-phase modulation and higher-order GVD     

Integrated-optic double-ring resonators with a wide free spectralrange of 100 GHz

Integrated-optic double-ring resonators with a wide free spectral range (FSR) of 100 GHz are fabricated using GeO₂-doped silica waveguides with a high relative refractive index difference (Δ) of 1.5%. The resonators are composed of two ring resonators comprising small ring waveguides with radii of 1.75 and 2.0 mm. The double-ring resonator module exhibited a wide FSR of 98.0 GHz, a finesse of higher than 138, a low crosstalk of less than -11.7 dB, and a low insertion loss of 6.1 dB. The measured FSR of 98.0 GHz is wider than any previously reported ring resonator composed of optical waveguides     

Hierarchical production control for a flow shop with dynamic setup changes and random machine breakdowns

In this paper, we study a manufacturing system consisting of two machines separated by two intermediate buffers, and capable of producing two different products. Each product requires a constant processing time on each of the machines. Each machine requires a constant non-negligible setup change time from one product to the other. The demand rate for each product is considered to be piecewise constant. Each machine undergoes failure and repair. The time-to-failure and time-to-repair are exponentially distributed random variables. The setup change and processing operations are resumable. We model our system as a continuous time, continuous flow process. An optimal control problem is formulated for the system to minimize the total expected discounted cost over an infinite horizon. To determine the optimal control policy structure, a discrete version of the problem is solved numerically using a dynamic programming formulation with a piecewise linear penalty function. A real-time control algorithm is then developed with the objective of maintaining low work-in-process inventory and keeping the production close to the demand. The algorithm uses a hierarchical control structure to generate the loading times for each product on each machine in real time and to respond to random disruptions in the system. The system is simulated using this algorithm to study its performance. The performance of the algorithm is also compared to alternative policies.