The crystal growth and thermoelectric properties of chromium disilicide

Single crystals of chromium disilicide about 8 mm in diameter and 35 mm long were grown using the floating zone technique. Measurements of electrical resistivity , Hall coefficient R and thermoelectric power were carried out in the temperature range from 85 to 1100 K. The values of and showed the anisotropy over the temperature range studied. The ratios parallel and perpendicular to the c-axis were / =1.9 and /=1.7 respectively, at room temperature. It was found to be a degenerate semiconductor having the hole concentration of 6.3×10²⁰ cm^–3 below 600 K. The effective masses of holes parallel and perpendicular to the c-axis determined from the thermoelectric power and the hole concentration near room temperature were estimated to be five and three times as large as a free electron mass, respectively. The calculation on the values of and was made using those effective masses. These values showed good agreement with the observed values in the temperature range from 150 to 1100 K.     

Constrained Motif Discovery in Time Series

The goal of motif discovery algorithms is to efficiently find unknown recurring patterns. In this paper, we focus on motif discovery in time series. Most available algorithms cannot utilize domain knowledge in any way which results in quadratic or at least super-linear time and space complexity. In this paper we define the Constrained Motif Discovery problem which enables utilization of domain knowledge into the motif discovery process. The paper then provides two algorithms called MCFull and MCInc for efficiently solving the constrained motif discovery problem. We also show that most unconstrained motif discovery problems be converted into constrained ones using a change-point detection algorithm. A novel change-point detection algorithm called the Robust Singular Spectrum Transform (RSST) is then introduced and compared to traditional Singular Spectrum Transform using synthetic and real-world data sets. The results show that RSST achieves higher specificity and is more adequate for finding constraints to convert unconstrained motif discovery problems to constrained ones that can be solved using MCFull and MCInc. We then compare the combination of RSST and MCFull or MCInc with two state-of-the-art motif discovery algorithms on a large set of synthetic time series. The results show that the proposed algorithms provided four to ten folds increase in speed compared the unconstrained motif discovery algorithms studied without any loss of accuracy. RSST+MCFull is then used in a real world human-robot interaction experiment to enable the robot to learn free hand gestures, actions, and their associations by watching humans and other robots interacting.     

On the high-temperature corrosion of Fe-Cr alloys in sulfur vapor

The mechanism of sulfidation of Fe-Cr alloys ranging from 8 to 97 wt.% chromium was determined from studies of scale structures, surface morphologies of scale, and reaction kinetics. Although the kinetics of sulfidation were quite similar to those previously determined by Mrowec et al., the structures in the present work were different, being triplex in nature. The growth mechanism of each layer was determined, and the overall sulfidation behavior was compared to the oxidation behavior. Many similarities between the two corrosion processes were observed.     

Effect of lipopolysaccharide on indices of peripheral and hepatic metabolism in lactating cows

Four multiparous lactating cows (175 to 220 d in milk [DIM]) were used in a 4 x 4 Latin square design to assess the effects of four doses (0.0, 0.5, 1.0, and 1.5 microg/kg of body weight) of lipopolysaccharide (LPS; Escherichia coli 0111:B4) on performance and plasma metabolite and hormone concentrations. In addition, effects of immune activation on in vitro hepatic metabolic capacity were evaluated in 12 multiparous lactating cows (150 to 220 DIM) infused with 0 (n = 6), 1.0 (n = 4) or 2.0 (n = 2) microg of LPS/kg. Milk production and DMI decreased linearly with LPS dose for 24 h after LPS infusion. Overall mean plasma tumor necrosis factor-alpha, insulin, glucagon, and cortisol concentrations increased linearly with LPS dose, and plasma beta-hydroxybutyrate decreased linearly by dose after LPS infusion. Infusion of LPS decreased the insulin:glucagon molar ratio, but did not affect plasma concentrations of growth hormone, insulin-like growth factor-1, leptin, or L-(+)-lactate. Plasma concentrations of glucose tended to increase initially and subsequently decrease, and there was a quadratic tendency for increased plasma nonesterified fatty acid concentrations after LPS administration. In vitro hepatic capacity for conversion of [1-(14)C]L-(+)-lactate and [1-(14)C]palmitate, but not [1-(14)C]propionate or [1-(14)C]L-alanine, to CO2 increased after LPS administration. Hepatic capacity to convert [1-(14)C]propionate to glucose tended to increase, but neither esterification nor the conversion of palmitate to acid soluble products was altered by LPS. The LPS infusion resulted in significant changes of endocrine mediators responsible for regulation of energy metabolism of lactating cows and tended to alter subsequent in vitro hepatic metabolic capacity.     

Reduction of droplet of tantalum oxide using double slit in pulsed laser deposition

We developed a double slit method in order to reduce droplets that were a problem in pulsed laser deposition (PLD) of tantalum oxide. The tantalum oxide films were deposited using KrF excimer laser ablation of a Ta target in 5 mass% O₃ at a pressure of 10 Pa. Stoichiometric and dense films with few droplets were obtained at a pressure of 10 Pa. Without double slit, as the laser pulses increased, the number of droplets containing rich metal on the film gets increased and its size became larger, and the surface morphology of the target also became more and more rugged. It was found that the number of droplet could be controlled by changing the initial roughness of the target. The number of droplets with a diameter size of under 1 μm was decreased to 1/10 of their sizes. Droplets larger than 3 μm, which mostly affect the corrosion resistance and hardly increase even beyond the laser pulses of 100 000. It is evident from this study that the double slit is a very effective method for reducing the droplets, which are otherwise a problem often seen in film production by PLD.     

Extraction of negative hydrogen ions from a compact 14 GHz microwave ion source

A pair of permanent magnets has formed enough intensity to realize electron cyclotron resonance condition for a 14 GHz microwave in a 2 cm diameter 9 cm long alumina discharge chamber. A three-electrode extraction system assembled in a magnetic shielding has formed a stable beam of negative hydrogen ions (H(-)) in a direction perpendicular to the magnetic field. The measured H(-) current density was about 1 mA∕cm(2) with only 50 W of discharge power, but the beam intensity had shown saturation against further increase in microwave power. The beam current decreased monotonically against increasing pressure.     

Water electrolysis under microgravity: Part 1. Experimental technique

Water electrolysis was conducted in both alkaline (25 wt.% KOH, 2 wt.% KOH) and acid (0.1N H₂SO₄) solutions for 8 s under microgravity environment realized in a drop shaft. The gas bubble formation of hydrogen and oxygen on platinum electrodes was observed by CCD camera. In alkaline solutions, a bubble froth layer grew on the electrode surface. Hydrogen bubble size was smaller than that of oxygen. The current density at constant potential decreased continually with time. In spite of the growth of a bubble froth layer on the electrode, the electrolysis never stopped, apparently because fresh electrolyte is supplied to the electrode surface by microconvection induced by the gas bubble evolution. In acid solution, hydrogen gas bubbles frequently coalesced on the cathode surface, yielding a larger average bubble than that of oxygen. The current density did not vary at constant potentials from –0.4 to −0.8 V versus reversible hydrogen electrode (RHE), because the effective electrode surface area was significantly reduced by the larger bubble size compared to alkaline electrolyte. The present experiments indicate that, especially in a microgravity environment, the bubble evolution behavior and the resultant current–potential curves are significantly influenced by the wettability of the electrode in contact with the electrolyte.     

Preparation of BaPbO3 Electrode Thin Films by RF Magnetron Sputtering

For electrode materials of Pb(Zr,Ti)O₃ (PZT) thin films in ferroelectric random access memory (FeRAM), various materials have been studied. As new electrode material with which the polarization and fatigue properties are improved, we take notice of barium metaplumbate BaPbO₃ (BPO). Because the BPO contained lead (Pb) and oxygen is conductor that adopted same perovskite structure as PZT. BPO thin films were prepared by rf magnetron sputtering on various substrates. (SiO₂/Si, MgO, Al₂O₃ and Pt-coated substrates), and influence of growth conditions (sputtering gas, rf power, the substrate-heating temperature and post anneals) on crystallization and conductivity were investigated. In case of post anneal after sputtering at room temperature, perovskite single phase was obtained above 400°C. In case of substrate heating while sputtering, without post anneal, perovskite single phase was obtained at 350–500°C on SiO₂/Si substrates (110) preferred orientation BPO films obtained at low temperature, and resistivity of the films decreased at decreasing sputtering temperature. Resistivity of the film at substrate temperature 350°C was 3 × 10^?3 Ω cm. In the case of single crystal substrate, the BPO films were epitaxially grown. Orientation of the films was varied with the sputtering condition. The epitaxial PZT thin films were also grown on the BPO, revealing that PZT(111)[011] //BPO(111)[011] //Pt(100)[011] //MgO(100)[011] and PZT(111)[011] //BPO(111)[011] //Pt(111)[011] //Al₂O₃(001)[100] structures were obtained, and their ferroelectric properties were also evaluated.     

Preparation and biological evaluation of hydroxyapatite-coated nickel-free high-nitrogen stainless steel

Calcium phosphate was formed on nickel-free high-nitrogen stainless steel (HNS) by chemical solution deposition. The calcium phosphate deposition was enhanced by glutamic acid covalently immobilized on the surface of HNS with trisuccinimidyl citrate as a linker. X-ray diffraction patterns and Fourier transform infrared spectra showed that the material deposited on glutamic acid-immobilized HNS within 24 h was low-crystallinity calcium-deficient carbonate-containing hydroxyapatite (HAp). The biological activity of the resulting HAp-coated HNS was investigated by using a human osteoblast-like MG-63 cell culture. The HAp-coated HNS stimulated the alkaline-phosphate activity of the MG-63 culture after 7 days. Therefore, HAp-coated HNS is suitable for orthopedic devices and soft tissue adhesion materials.     

Fabrication of high‐strength steel fibre reinforced metal matrix composites by explosive bonding and their tensile properties

Summary

Steel fibre reinforced metal matrix composites (FRM) consisting of high‐strength ductile steel wire and aluminium or titanium foil were fabricated by explosive bonding. The strength properties were evaluated by tensile tests. The optimum explosive loading (explosive mass/driver plate mass) increases with the volume fraction of fibre. For the aluminium matrix composites, the micrographs obtained show sound bonding between the adjoining foils and non‐bonding between the foil and steel wire. The tensile strength of the aluminium matrix composites is 80% of the value predicted by the rule of mixtures. For the titanium matrix composites, the micrographs obtained show both bonded and unbonded regions between the adjoining foils or between the foil and steel wire. The tensile strength of the titanium matrix composites agrees with the value predicted by the rule of mixtures.