Feasibility of Sludge Ozonation for Stabilization and Conditioning

A pilot-scale sludge treatment plant was built to investigate the feasibility of ozonation processes for waste activated sludge treatment. Ozonation of wastewater sludge resulted in mass reduction by mineralization as well as by supernatant and filtrate recycle. Another advantage of sludge ozonation is a significant improvement of settleability and dewaterability. Experimental results showed that mass reduction of 70% and volume reduction of 85% compared with the control sludge was achieved through the sludge ozonation at a dose of 0.5?gO₃/gDS. It is also interesting to note that the filterability deteriorates up to ozone dose of 0.2?gO₃/gDS and then improves considerably at a higher ozone dose. The filterability could be improved by chemical conditioning even at a low ozone dose. The economic feasibility by cost analysis reveals that ozonation processes can be more economical than other alternative processes for sludge treatment and disposal at small-sized wastewater treatment plants.     

The Effect of Aluminum Ions on the DC Etching of Aluminum Foil

A study has been made of the electrochemical etching of 99.99% aluminum foils at a current density of 50 mA cm^–2in AlCl₃–HCl solutions (1 m Cl^–) at 80 °C. The solutions were made by dissolving metallic aluminum into 1m HCl solution, to give a Cl^– concentration of 1 m. The number density of etch tunnels and the homogeneity of tunnel length decreased, and the mean pit size and its standard deviation increased with increasing Al³⁺ concentration. The results were discussed based on potential transients at a current density of 50 mA cm^–2, current–potential curves at a scan rate of 10 m Vs^–1 and electrochemical impedance spectra.     

Migration of Intergranular Liquid Films and Formation of Core-Shell Grains in Sintered TiC–Ni Bonded to WC–Ni

When TiC–20 wt% Ni powder mixtures are sintered at 1400°C, relatively large TiC grains possibly containing some Ni form with near-equilibrium shapes. When these specimens are heat-treated again at 1400°C in contact with sintered WC–20 wt% Ni pieces, the liquid films between the TiC grains in the contact region migrate against their increasing curvatures, forming (Ti,W)C solid solution behind them. These migrating liquid films reverse their directions on further heat-treatment. As in other alloys, this liquid film migration must be driven by the coherency strain energy produced by W diffusion at the surface of the dissolving TiC grains. Shells of (Ti,W)C solid solution also form around the cores of TiC grains near the contact region, and this process is probably driven by both coherency strain energy and free energy of mixing. At some contact regions, (Ti,W)C precipitates nucleate and grow, probably driven mainly by the free energy of mixing. In powder mixtures, the formation of core-shell grains is expected to be driven by the coherency strain energy, the free energy of mixing, and the capillary effect.     

Separation of Triacylglycerol Species from Interesterified Oils by High-Performance Liquid Chromatography

Using a 1,3-regioselective lipase as a catalyst, soybean oil and olive oil were interesterified with the short-chain triacylglycerol tributyrin (1,2,3-tributyrylglycerol) to produce mixtures of structured triacylglycerols (SL-TAG). The SL-TAG were purified by column chromatography and analyzed by both normal-phase (silica column; NP_SIL) and reversed-phase [octadecyl silane (ODS) column] high-performance liquid chromatography (HPLC). Individual SL-TAG molecular species were detected by evaporative light-scattering detection, and characterized by mass spectrometry. NP_SIL HPLC successfully separated the newly synthesized SL-TAG into two groups of TAG: one composed of one butyryl group and two long-chain fatty acyl groups (from soybean or olive oil); the second was composed of two butyryl groups and one long-chain fatty acyl group. The SL-TAG species were further analyzed by reversed-phase HPLC which gave a more detailed separation of the TAG species present in the two SL-TAG.     

Analysis of microbial adaptation at enzyme level for enhancing biodegradation rate of BTX

Catechol was found to be a common intermediate in the degradation of benzene and toluene byAlcaligenes xyhsoxidans Y234, and the ring cleavage of the catechol mediated by catechol 1,2-dioxygenase was a rate-determining step. Since benzene induced higher level of catechol 1,2-dioxygenase than toluene, the cells pre-adapted to benzene showed higher degradation rate of benzene and toluene. The degradation rate ofm-xylene was also increased significantly when benzene-adapted cells were inoculated.m-Xylene was metabolized via 3-methyl catechol which was effectively cleaved by catechol 1,2-dioxygenase.     

Three-dimensional modelling of Non-Newtonian fluid flow in a coat-hanger die

The three-dimensional model of isothermal flow of power-law fluid in a coat-hanger die has been developed using finite element method. The shape of coat-hanger die used in the present model was determined according to the previous analytical design equation which is based on one-dimensional flow model in the manifold and the slot. Because uniform flow rate across the die outlet is most important to achieve uniform thickness of extruded polymer sheet or film, flow rate distribution is mainly examined to determine the valid process condition for the design equation as the design parameters are changed. The effects of fluid property in terms of power-law index and process parameters not considered in one-dimensional design equation such as die inlet size and the presence of land were analyzed. Results show that the manifold angle is the most influencing design parameter on flow rate distribution. When the material of different power-law index from design value is processed, the change of power-law index affects the uniformity of flow rate appreciably.     

Efficient usage of highly dispersed Pt on carbon nanotubes for electrode catalysts of polymer electrolyte fuel cells

A Pt-deposited carbon nanotube (CNT) shows higher performance than a commercial Pt-deposited carbon black (CB) with reducing 60% Pt load per electrode area in polymer electrolyte fuel cells (PEFCs) below 500 mA/cm². K₂PtCl₄ and H₂PtCl₆·6(H₂O) are used for the Pt deposition onto multi-walled CNTs (MWCNTs), which are produced by the catalytic decomposition of hydrocarbons. The electric power densities produced using the Pt/CNT electrodes are greater than that of the Pt/CB by a factor of two to four on the basis of the Pt load per power. CNTs are thus found to be a good support of Pt particles for PEFC electrodes. TEM images show 2–4-nm Pt nanoparticles dispersed on the CNT surfaces. These high performances are considered to be due to the efficient formation of the triple-phase boundaries of gas–electrode–electrolyte. The mechanisms of Pt deposition are discussed for these Pt-deposited CNTs.     

Preparation and characterization of polypropylene/layered silicate nanocomposites using an antioxidant

Polypropylene (PP)/layered silicate nanocomposites were prepared via simple melt mixing of three components, PP, layered silicates modified with octadecylamine (C18-MMT) and antioxidant, to investigate the role of antioxidant. TEM and X-ray scattering results confirmed the intercalated state of silicates in PP/layered silicate nanocomposites with antioxidant. In rheological and mechanical study, the nanocomposites with antioxidant showed higher properties than those of the unfilled PP. The nanocomposite with 5 wt% C18-MMT and 0.5 phr antioxidant exhibited about 1.4 times higher tensile modulus and 1.3 times higher storage modulus than the unfilled PP. However, PP/C18-MMT without antioxidant showed lower rheological values owing to the thermal decomposition of PP and the poor compatibility between PP and C18-MMT. It could be concluded that antioxidants played an important role in enhancing the compatibility between PP and C18-MMT. According to the real time X-ray diffraction, the nanocomposite showed the weak ordering of PP crystals than the unfilled PP in the load-extension plateau region of elongation.     

Wetting properties of polystyrene ionomers treated with plasma source ion implantation

The wetting properties of polystyrene‐based ionomers treated with plasma source ion implantation (PSII) were investigated by the measurement of water contact angles. When sulfonated ionomers were aged for a few days, the hydrophobic recovery for the ionomers became much slower than that for the nonionic polymers. However, when the samples were aged over 20 days, the water contact angle of the ionomers converged with that of the nonionic polymer. Thus, it was concluded that the ionic interaction between the ionic groups and the presence of ionic groups together resulted in the slow hydrophobic recovery and that the aging effect was significant for the ionomers. For the methacrylate ionomer of low ion content, on the other hand, it was found that the PSII treatment produced only a small change in hydrophobic recovery behavior. Thus, it was suggested that the low ionic content coupled with the small size of the ionic unit might cause changes only of a very insignificant degree in hydrophobic recovery behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2500–2504, 2002     

Preparation of microporous chlorinated poly(vinyl chloride) membrane in fabric and the characterization of their pore sizes and pore‐size distributions

Chlorinated poly(vinyl chloride) (CPVC)/poly(vinyl pyrrolidone) (PVP) membranes were prepared by using the solvent system tetrahydrofuran (THF)/n‐butyl alcohol (n‐BA) to investigate the possibility of pore size and pore‐size distribution control. The coagulation of CPVC/PVP solution was induced by the exposure to water vapor at 25 (±0.5)°C. The average pore diameter, d_p, and the size distribution of pores on the surface of the membrane were quantified through the image analyzer from the images visualized by field emission scanning electron microscope (FE‐SEM). Surface pore size and distribution of the prepared CPVC/PVP membrane were strongly affected by the relative humidity (RH) in the environment and the content of PVP used as an additive. Particularly, in the case of CPVC membrane without PVP, the mean pore size was 0.15–0.2 μm, depending on the RH. The pore distribution became broad with the increase of the RH. The membranes had open pores as confirmed by the hydraulic permeation experiment. In addition, the water flux and membrane resistance (R_m) were greatly affected by the composition of polymer solution and the RH. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1195–1202, 2002