一种新的S/PDIF接收机数据译码的实现方法

论文分析了S/PDIF音频数据流的特点,引入模式识别中的训练机对S/PDIF音频数据流进行现场脉冲宽度特征提取。依据训练机结果建立分类器实现脉冲宽度分类,根据脉冲宽度进行同步前置码和逻辑电平的解码。利用硬件描述语言Verilog进行设计实现与验证,仿真结果说明这种特征提取方法可以提高S/PDIF接收机数据解译码的适应性和准确性。     

基于B/S的资料信息管理系统的设计和实现

该文介绍了基于B/S资料信息管理系统的设计和开发,重点阐述了资料信息管理系统的开发设计的难点和要点,同时提供了部分数据库表信息和代码。     

含锆介孔材料的研究进展

介绍了目前国内外对介孔氧化锆和含锆介孔二氧化硅材料的研究状况,包括合成介孔氧化锆的2种主要体系水热体系和非水体系,以及在介孔二氧化硅中引入锆的主要方法直接合成法和溶液浸渍法,这2类材料在化学、光学、电子学、电磁学、材料学、环境学等诸多领域具有巨大的潜在应用价值.     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...     

基于主成分分析中的几类问题的计算公式及结论

讨论了主成分分析中的几类问题的计算方法,重点揭示在协方差矩阵中对角元素相同时的第一主成分及贡献率和对角元素不同时的主成分贡献率．经讨论后给出有关计算公式,并说明这些计算公式在多元统计分析中的实际作用     

Effect of fretting amplitudes on fretting wear behavior of steel wires in coal mines

Given that fretting wear causes failure in steel wires, we carried out tangential fretting wear tests of steel wires on a self-made fretting wear test rig under contact loads of 9 and 29 N and fretting amplitudes ranging from 5 to 180 μm. We observed morphologies of fretted steel wire surfaces on an S-3000N scanning electron microscope in order to analyze fretting wear mecha-nisms. The results show that the fretting regime of steel wires transforms from partial slip regime into mixed fretting regime and gross slip regime with an increase in fretting amplitudes under a given contact load. In partial slip regime, the friction coefficient has a relatively low value. Four stages can be defined in mixed fretting and gross slip regimes. The fretting wear of steel wires in-creases obviously with increases in fretting amplitudes. Fretting scars present a typical morphology of annularity, showing slight damage in partial slip regime. However, wear clearly increases in mixed fretting regime where wear mechanism is a combination of plastic deformation, abrasive wear and oxidative wear. In gross slip regime, more severe degradation is present than in the other regimes. The main fretting wear mechanisms of steel wires are abrasive wear, surface fatigue and friction oxidation.     

有限导流垂直裂缝产能及影响因素研究

从渗流理论出发,利用瞬时源、连续源的思想,结合卷积公式、Laphce变换等方法,建立了有限导流垂直裂缝井的产能计算模型,对模型导出的积分方程采用边界元方法(BEM)在Laplace空间进行了求解,利用Stehfest数值反演.获得了实空间的解,从而给出了准确计算有限导流垂直裂缝井产量的方法.此外,还通过定量计算分析了裂缝各设计参数对产量的影响方式和影响程度.通过分析可知,压裂井的日产量随裂缝长度、裂缝渗透率、裂缝宽度的增加而增大,但其产量增加的幅度随三种因素的增大而逐渐减小,因此在实际的油藏水力压裂设计时,应结合压裂成本和增益来考虑合适的设计参数.对压裂井产量预测和水力压裂油藏工程设计具有一定价值.