Effect of curing time on microstructure and mechanical strength development of alkali activated binders based on vitreous calcium aluminosilicate (VCAS)

The aim of this paper is to study the influence of curing time on the microstructure and mechanical strength development of alkali activated binders based on vitreous calcium aluminosilicate (VCAS). Mechanical strength of alkali activated mortars cured at 65 °C was assessed for different curing times (4–168 h) using 10 molal NaOH solution as alkaline activator. Compressive strength values around 77 MPa after three days of curing at 65 °C were obtained. 1·68 MPa/h compressive strength gain rate was observed in the first 12 h, decreasing to 0·95 MPa/h for the period of 12–72 h. The progress of geopolymeric reaction was monitored by means of TGA and, electrical conductivity and pH measurements in an aqueous suspension. Significant decrease in pH and electrical conductivity were observed in the 4–72 h period, demonstrating the geopolymerization process. Furthermore, SEM images showed an important amount of (N, C)ASH gel and low porosity of the developed matrix.     

Phase and Rheological Behavior of Cetyldimethylbenzylammonium Salicylate (CDBAS) and Water

The temperature–composition phase diagram in the diluted region of the cationic surfactant cetyldimethylbenzylammonium salicylate/water system was studied with a battery of techniques. The Krafft temperature (T _k = 33 ± 1 °C) was measured by differential scanning calorimetry, polarizing microscopy, conductimetry, viscosimetry, and rheometry. The critical vesicle concentration (cvc, ~0.002 wt%) and a vesicle–micellar transition (cvm, ~0.005 wt%) was detected at a temperature of 35 °C. Below T _k and concentrations ≤2 wt%, a transparent solution is formed (I). Above 2–8.5 wt%, a lamellar (L₁) phase forms. At higher concentrations and up to 12 wt%, a second lamellar phase (L₂) is detected. From 12.4 to 15.5 wt%, an emulsion phase (E) is formed. Rheological dynamic measurements for the I phase indicate that the system exhibits a predominantly viscous behavior (G′ < G″) for concentrations lower than the overlap or entanglement concentration (C _e, ~0.75 wt%). At higher concentrations, wormlike micelles form and the elastic behavior predominates (G′ > G″). The elastic (G′) modulus collapses in a concentration–time master curve in the whole reduced frequencies range ωτ _c examined, whereas the viscous modulus (G″) collapses only at reduced frequencies lower than 0.1. Reduced stress plotted as a function of the reduced shear rate yields a good superposition of the curves at the different concentrations up to the onset of the non-linear behavior.     

Polyacrylamide-gelatin polymeric networks: effect of pH and gelatin concentration on the swelling kinetics and mechanical properties

This work presents the synthesis of polyacrylamide-gelatin (PAM-G) semi-interpenetrating hydrogels, as well as the study of the swelling capacity of this material at different pH’s, and we report its Young modulus. The hydrogels were crosslinked with N,N′-methylenebisacrylamide and synthesized at different acrylamide/gelatin weight relationship. It was observed that the swelling capacity of the hydrogels increases when the gelatin concentration is increased; while the Young modulus (at the swelling equilibrium) decreases lightly. Therefore, the gelatin has a small effect in the Young modulus, unlike its influence in the swelling ability. The swelling experiments reveal that the PAM-G hydrogels increase its swelling capacity in alkaline mediums because the presence of the hydrophobic functional groups (mainly COO⁻) in the gelatin structure.     

2D operators on topographic and non‐topographic architectures—implementation,efficiency analysis,and architecture selection methodology

Topographic and non‐topographic image processing architectures and chips, developed within the CNN community recently, are analyzed and compared. It is achieved on a way that the 2D operators are collected to classes according to their implementation methods on the different architectures, and the main implementation parameters of the different operator classes are compared. Based on the results, an efficient architecture selection methodology is formalized. Copyright © 2010 John Wiley & Sons, Ltd.     

An experimental investigation on the influence of phenol on the solubility of CO2 in aqueous solutions of NaOH

Experimental results are presented for the solubility of CO₂ in an aqueous solution of phenol and NaOH (molalties in water: phenol: 0.5; NaOH: 1.0) at (314, 354, and 395) K and pressures up to 10 MPa. The experimental work extends recent investigations on the influence of phenol as well as of (phenol + NaCl) on the solubility of CO₂ in water. In contrast to those previous investigations, the strong electrolyte reacts with carbon dioxide and also with phenol. The experimental results are compared with predictions from a thermodynamic model. That model combines a model for the “chemical” solubility of CO₂ in aqueous solutions of NaOH with a model for the “physical” solubility of CO₂ in aqueous solutions of phenol. An extension is introduced to account for the chemical reaction between the weak acid phenol and the strong base sodium hydroxide. The prediction results nicely agree with the new experimental data. © 2015 American Institute of Chemical Engineers AIChE J, 61: 2832–2840, 2015     

Controlling Argan Seed Quality by NIR

The suitability of using visible/near infrared spectroscopy (Vis/NIR), as a rapid and non‐destructive technique for monitoring the quality of argan seeds (Argania spinosa Skeels) was studied. The analyzed parameters were the fatty acid composition of argan seed oil, seed moisture content, seed oil content and oil stability index (OSI). The ratio between major unsaturated and saturated fatty acids (U/S) during the oxidation assay at constant temperature was studied. Values from infrared drying were used as a laboratory reference for the moisture. Argan seed oil content was determined by Soxhlet extraction. A fatty acid analysis was carried out by gas chromatography and the OSI was determined by the Rancimat test. Predictive models of argan seed moisture, ratio U/S and OSI showed good accuracy. Therefore, Vis/NIR measurements can be used for controlling several argan seed quality parameters. This procedure might be of interest to the argan oil industry, which is currently in the process of modernization and expansion.     

Enhancing the electrical conductivity of carbon black/graphite nanoplatelets: Poly(ethylene‐butyl acrylate) composites by melt extrusion

The influence of processing parameters such as screw geometry, temperature profile, and screw speed on the electrical properties of hybrid composites consisting of graphite nanoplatelets and carbon black in ethyl butyl acrylate was studied. Two different screws were used to compound the hybrid composites at two different temperatures and two different screw speeds. A beneficial effect was noted with regard to the electrical properties when adding nanoplatelets to the filler system. The cause could be a synergistic effect due to the difference in particle shape of the two fillers. Lower percolation thresholds were obtained with the conventional screw due to less breakage of the graphite nanoplatelets compared to the barrier screw. No significant changes of the electrical properties were observed when changing the temperature profiles or the screw speeds. Furthermore, the melt viscosity of the compounds was not appreciably affected at the rather low filler contents used here. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42897.     

Inline electron holography and VEELS for the measurement of strain in ternary and quaternary (In,Al,Ga)N alloyed thin films and its effect on bandgap energy

We present the use of (1) dark‐field inline electron holography for measuring the structural strain, and indirectly obtaining the composition, in a wurtzite, 4‐nm‐thick InAlGaN epilayer on a AlN/GaN/AlN/GaN multinano‐layer heterosystem, and (2) valence electron energy‐loss spectroscopy to study the bandgap value of five different, also hexagonal, 20–50‐nm‐thick InAlGaN layers. The measured strain values were almost identical to the ones obtained by other techniques for similarly grown materials. We found that the biaxial strain in the III‐N alloys lowers the bandgap energy as compared to the value calculated with different known expressions and bowing parameters for unstrained layers. By contrast, calculated and experimental values agreed in the case of lattice‐matched (almost unstrained) heterostructures.     

Titanium diffusion in shinbone of rats with osseointegrated implants

Dental implants are composed of commercially pure Ti (which is actually an alloy of titanium, and minor or trace components such as aluminium and vanadium). When the implant is inserted, its surface undergoes a number of chemical and mechanical processes, releasing particles of titanium to the medium. The metabolism of free ions of titanium is uncertain; the uptaking processes in the body are not well known, nor their toxic dose. In addition, physical properties of newly formed bone, such as diffusivity and activation energy, are scarce and rarely studied. In this study, we analysed the diffusion of titanium in the titanium‐implanted shinbones of six adult male Wistar rats by spatially resolved micro x‐ray fluorescence. The measurements were carried out at the microfluorescence station of the x‐ray fluorescence (XRF) beamline of the Brazilian synchrotron facility LNLS (from Portuguese ‘Laboratorio Nacional de Luz Sincrotron’). For each sample, XRF spectra were taken by linear scanning in area near the new bone formed around the Ti implant. The scanning line shows a clear effect of titanium diffusion whereas calcium intensity presents a different behaviour. Moreover, a clear correlation among the different structures of bones is observed in the Ti and Ca intensities. The results obtained in these measurements may allow determining quantitatively the parameters of diffusion rates and other physical properties of new bone like diffusion coefficients.