Development of a simple microsystems membrane probe card

Presented here are details of the development of a novel membrane integrated circuit (IC) probe card structure based on microsystems technology. The device design allows probing of both solder bumps and pads. A self-limiting sensor was integrated to prolong device lifetime. Comparison with and discussion of the use of modelling is made. Possible enhancements to the probing structure are discussed to improve alignment and measurements. Also shown is data using our microsystems probe card to access a simple IC device. Our device has a contact resistance of less than 0.5 Ω for a force of 0.004 N. A method to implement our probing structure for commercial application and the potential developments which can be made to improve its ease of use are then discussed.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Improved homogenization of Ni in sintered steels through the use of Cr-containing prealloyed powders

The homogenization of Ni in powder metal (PM) steel compacts is usually difficult even after high-temperature sintering at 1250°C. An earlier study by the authors demonstrated that this problem can be alleviated through the addition of 0.5 wt pct Cr in the form of stainless steel powders. To further improve the microstructure and mechanical properties of Ni-containing PM steels and to understand the mechanisms, an attempt was made in this study using the Fe-3Cr-0.5Mo prealloyed powder as the base material. The results showed that the distribution of the Ni additives was significantly improved. As a result, the tensile strength of the Fe-3Cr-0.5Mo-4Ni-0.5C compact sintered at 1250°C reached 1323 MPa. The elongation was higher than 1 pct. These sinter-hardened properties, which were attained using a slow furnace cooling rate, were comparable to those of the sinter-hardened alloys reported in the literature using accelerated cooling and were equivalent to those of the best quenched-and-tempered alloys registered in the Metal Powder Industries Federation (MPIF) standards. These improvements were attributed to the positive effect of Cr addition on alloy homogenization due to the reduction of the repelling effect between Ni and C, as was demonstrated through the thermodynamic analysis using the Thermo-Calc program.     

Note on B-splines, wavelet scaling functions, and Gabor frames

Let g be a continuous, compactly supported function on such that the integer translates of g constitute a partition of unity. We show that the Gabor system (g,a,b), with window g and time-shift and frequency-shift parameters a,b>0 has no lower frame bound larger than 0 if b=2,3,... and a>0. In particular, (g,a,b) is not a Gabor frame if g is a continuous, compactly supported wavelet scaling function and if b=2,3,... and a>0. We give an example for our result for the case that g=B/sub 1/, the triangle function supported by [-1,1], by showing pictures of the canonical dual corresponding to (g,a,b) where ab=1/4 and b crosses the lines N=2,3,.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Structure and electrical characteristics of Ce4+-doped Ba2In2O5

The In-site of Ba₂In₂O₅ with Brownmillerite structure was partially substituted for Ce⁴⁺ ions in order to examine the doping effect on the order-disorder transition. Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1, 0.2, 0.3, 0.5, 1.0, and 1.5) were prepared by solid state reaction. X-Ray diffraction analyses of these powder samples demonstrated that Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1 and 0.2) possesses Brownmillerite structure. With increasing content of Ce⁴⁺ ion the crystal system of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.3, 0.5, and 1.0) changed to cubic perovskite structure above the order-disorder transition temperature of Ba₂In₂O₅. Arrhenius plots of the electrical conductivities of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.2, 0.3, and 1.0) exhibited no discontinuity. These compounds had high transference numbers of oxide ion above 973 k.     

Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.