Results of testing a centrifugal bubble singlet-oxygen generator

The results of parametric tests of a centrifugal bubble singlet-oxygen generator based on the reaction of chlorine with an alkaline hydrogen peroxide solution have been given. The utilization of chlorine grows with bubble-layer height, whereas the relative content of O₂(¹Δ) remains constant. Growth in centrifugal acceleration leads to a more efficient utilization of chlorine. A specific oxygen output of more than 1 mmole·cm⁻²·sec⁻¹ from the bubble layer for a degree of chlorine utilization of ∼95% and a singlet-oxygen yield of more than 50% has been attained. It has been shown that a centrifugal bubble singlet-oxygen generator is an efficient energy source for an oxygen-iodine laser. __________ Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 80, No. 3, pp. 121–128, May–June, 2007.     

Fast numerically stable computation of orthogonal Fourier?Mellin moments

An efficient algorithm for the computation of the orthogonal Fourier-Mellin moments (OFMMs) is presented. The proposed method computes the fractional parts of the orthogonal polynomials, which consist of fractional terms, recursively, by eliminating the number of factorial calculations. The recursive computation of the fractional terms makes the overall computation of the OFMMs a very fast procedure in comparison with the conventional direct method. Actually, the computational complexity of the proposed method is linear O(p) in multiplications, with p being the moment order, while the corresponding complexity of the direct method is O(p²). Moreover, this recursive algorithm has better numerical behaviour, as it arrives at an overflow situation much later than the original one and does not introduce any finite precision errors. These are the two major advantages of the algorithm introduced in the current work, establishing the computation of the OFMMs to a very high order as a quite easy and achievable task. Appropriate simulations on images of different sizes justify the superiority of the proposed algorithm over the conventional algorithm currently used     

CMOS gyrator-C active transformers

A systematic approach for synthesising gyrator-C active transformers using MOS transistors is presented. The topology of gyrator-C active inductors and their characteristics are briefly reviewed first. This is followed by the development of ideal gyrator-C active transformers, where only the capacitor loads of the transconductors synthesising active transformers are considered. The self and mutual inductances of both the primary and secondary windings of active transformers are investigated in detailed. Non-ideal gyrator-C active transformers are developed with the consideration of both the resistance and capacitance loads of transconductors. The intrinsic relation between the self and mutual inductances is derived. The configuration of gyrator-C active transformers with multiple primary and secondary windings is also developed. The proposed active transformers offer large and tunable self and mutual inductances with virtually no silicon area requirement. Several practical implementations of the proposed active transformers have been realised in TSMC-0.18 mum 1.8 V CMOS technology and analysed using SpectreRF with BSIM3v3 device models. Simulation results on voltage transfer characteristics, self and mutual inductances, quality factors, stability, the effect of process variations, and noise are presented. The application of the proposed active transformers is exemplified using a 1.6 GHz active transformer quadrature oscillator.     

Itemset trees for targeted association querying

Association mining techniques search for groups of frequently co-occurring items in a market-basket type of data and turn these groups into business-oriented rules. Previous research has focused predominantly on how to obtain exhaustive lists of such associations. However, users often prefer a quick response to targeted queries. For instance, they may want to learn about the buying habits of customers that frequently purchase cereals and fruits. To expedite the processing of such queries, we propose an approach that converts the market-basket database into an itemset tree. Experiments indicate that the targeted queries are answered in a time that is roughly linear in the number of market baskets, N. Also, the construction of the itemset tree has O(N) space and time requirements. Some useful theoretical properties are proven.     

The X-HPD—conceptual study of a large spherical hybrid photodetector

We present the results of a conceptual study demonstrating the feasibility of a large spherical hybrid photodetector with central anode. A prototype tube with 208 mm diameter and an anode in form of a metallic cube has been fabricated. In the final version of the so-called X-HPD concept the anode will be a scintillator cube with plated faces and a small photodetector to readout the bottom. The bialkali photocathode covers three quarters of the sphere surface. Combined use of this cathode in transmissive and reflective mode leads to effective quantum efficiency values exceeding those obtained in conventional hemispherical PMT designs. Further features of the concept are a photoelectron collection efficiency approaching 100% and a photon amplification in the scintillator crystal leading to a distinct single photoelectron signal.

Using a custom built electron accelerator based on a CsI transmissive photocathode, LSO and YAP block crystals in geometries adapted to the anode of an X-HPD have been tested with single photoelectrons in the 10–30 keV energy range. The scintillation light was readout with a conventional PMT or a Si-PM. More than 30 photoelectrons per incident electron could be detected with the PMT.     

Low-cycle fatigue in silicon: comparison with fcc metals

Undoped FZ silicon single crystals were cyclically loaded in tension‐compression under plastic strain amplitude control in a temperature and strain rate domain where the glide of dislocations is still controlled by the lattice friction: 1073–1173 K and (1.5–6) × 10⁻⁴s⁻¹; the plastic strain amplitude being varied from 6 × 10⁻⁴ to 10⁻². Cyclic hardening curves display logarithmic then linear hardening and pass through a maximum before the peak stress per cycle stabilizes. The maximum and stabilized stresses decrease when temperature increases. Microscopical observations suggest that strain localization takes place near the maximum cyclic stress and beyond. But, contrary to what is observed in fcc metals, the maximum or saturation stress decreases when the strain amplitude per cycle increases. Several types of dislocation arrangements, rather different from those found in copper, but looking more similar to Ni fatigued at low temperatures, were revealed by transmission electron microscopy. Before mechanical saturation, edge dislocation dipoles gather in thick stripes forming more or less corrugated walls, depending on the amplitude per cycle, when viewed normal to the primary slip plane. Once the maximum stress is reached, it seems that parts of the microstructure cease to participate in the imposed plastic strain, while others concentrate it. In active areas, thick walls condense into much thinner ones, forming chevrons when viewed normal to the slip plane. In areas which seem to be inactive, dipolar walls anneal out leaving a rather homogeneous distribution of prismatic loops. Thin PSBs with a well‐characterized ‘ladder‐structure’ are very rare. Characteristic lengths of the observed patterns are given and briefly discussed using current theories of cyclic deformation.     

Brittle fracture of high-strength steels at very low temperatures

High-strength steels are used to increase the load carrying capacity of components. However, to guarantee a safe design, it is also necessary to combine high strength with adequate fracture toughness. In this paper, fracture toughness of three high-strength steels with yield strengths ranging from 460 to 890 MPa has been studied at very low temperatures. Taking into account experimental evidence, a new mechanism of cleavage at very low temperatures is proposed. This mechanism considers the possibility of reaching the ideal strength (the stress at which the lattice of a single crystal losses its stability) in the immediate vicinity of the fatigue crack tip. Moreover, a computational model able to calculate the external load needed to produce a catastrophic failure of these steels has been developed.     

S-N-P curves in 7075 T7351 and 2024 T3 aluminium alloys subjected to surface treatments

The S-N-P (stress, number of cycles, failure probability) curves for 2024 T3 and 7075 T7351 aluminium alloys were obtained. Previously, surface treatments of degreasing and different types of anodizing were applied to samples, evaluating the influence of these treatments on the fatigue life of the alloys. The determination of the S-N-P curves was done using Maennig's method. Rotary fatigue was used because this technique produces greater stress on the sample surfaces, the zone in which it is important to evaluate fatigue resistance. Both the transition range and the finite life range were evaluated, calculating the 1, 50 and 99% fracture probability. SEM was performed in order to characterize the fracture micromechanism. The conclusions were that Maennig's method is useful to evaluate fatigue life of these materials in a fast and efficient manner. Moreover, surface treatments produce a decrease in the fatigue life of both alloys, associating this effect with the surface damage produced on each sample during the treatment.