TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.     

An effective compact analyzer of electron spin polarization

A compact electron polarimeter employing the classical Mott scheme has been developed and tested. The device has an efficiency of about 5.6×10⁻⁴, a maximum count rate of 5×10⁵ cps, dimensions 15 cm (diameter) × 25 cm (length), and a working voltage of 40 kV. The polarimeter can operate for a long time under arbitrary vacuum conditions without maintenance, exhibiting no changes in the main working characteristics, and obeys all requirements to the electron spin polarization studies on the modern level.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

Some Specific Features of Degradation of Superheater Tubes of the Boilers of Thermal Electric Power Plants Made of 12Kh18N12T Steel

We study the process of degradation and damage for superheater tubes of the pressure boilers of power plants made of austenitic chromium-nickel steel. The role of sensitization and partial sigmatization of austenitic steel in the embrittlement of the tubes is analyzed.__________Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 40, No. 4, pp. 81–86, July–August, 2004.     

Thermomechanical finite-element model of shell behavior in continuous casting of steel

A coupled finite-element model, CON2D, has been developed to simulate temperature, stress, and shape development during the continuous casting of steel, both in and below the mold. The model simulates a transverse section of the strand in generalized plane strain as it moves down at the casting speed. It includes the effects of heat conduction, solidification, nonuniform superheat dissipation due to turbulent fluid flow, mutual dependence of the heat transfer and shrinkage on the size of the interfacial gap, the taper of the mold wall, and the thermal distortion of the mold. The stress model features an elastic-viscoplastic creep constitutive equation that accounts for the different responses of the liquid, semisolid, delta-ferrite, and austenite phases. Functions depending on temperature and composition are employed for properties such as thermal linear expansion. A contact algorithm is used to prevent penetration of the shell into the mold wall due to the internal liquid pressure. An efficient two-step algorithm is used to integrate these highly nonlinear equations. The model is validated with an analytical solution for both temperature and stress in a solidifying slab. It is applied to simulate continuous casting of a 120 mm billet and compares favorably with plant measurements of mold wall temperature, total heat removal, and shell thickness, including thinning of the corner. The model is ready to investigate issues in continuous casting such as mold taper optimization, minimum shell thickness to avoid breakouts, and maximum casting speed to avoid hot-tear crack formation due to submold bulging.     

Glycoconjugated polymer 6. Synthesis of poly[styrene-<Emphasis Type="Italic">block</Emphasis>-(styrene-<Emphasis Type="Italic">graft</Emphasis>-amylose)] via potato phosphorylase-catalyzed polymerization

Summary The potato phosphorylase-catalyzed polymerization of α-D-glucose-1-phosphate (G-1-P) onto poly[styrene-block-(4-vinylbenzyl maltohexaoside)] (1) was performed at the molar ratios of [G-l-P]₀ and [maltohexaose]₀ of 35, 80, and 250. The product was found to be soluble in dimethyl sulfoxide, which was a good solvent for amylose, and showed the complex-formation with iodine, indicating that the product was assignable to poly[styrene-block-(styrene-graft-amylose)] (2). The quantitative analysis of the liberated phosphoric acid gave the average degree of polymerization o f the glucose unit (n) as 27, 5 1, and 180 for 2-I, 2-II, and 2-III, respectively. Received: 29 November 2002/Accepted: 22 December 2002 Correspondence to Toyoji Kakuchi     

Adaptive agents and multiagent systems

New information systems and recent applications (grid computing, Web Services, and so on) are often distributed, large-scale, open, heterogeneous, and characterized by a dynamic environment. To model these complex systems, researchers have spent much effort during the last few years on multiagent systems. The aim is to model complex distributed systems as a set of (possibly organized) software agents that interact in a common environment. The decomposition of a system into a number of agents lets the system react and adapt better in a changing environment. Moreover, organized structures ("social" structures) can emerge from interactions between agents, which in turn constrain and coordinate the agents' behavior. A multiagent system takes its metaphors of interaction from social systems rather than using the metaphor of the isolated thinker that early artificial intelligence researchers preferred. An important issue when dealing with this increasing complexity is to build adaptive agents and multiagent systems. Agents and multiagent systems must be aware of their own capabilities and of changes to other agents and their environment. To remain effective, agents must be able to adapt their structures and knowledge while they execute.